Extron electronics DTP3 T/R 301 Manuale utente

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DTP3 T/R 301 • Setup Guide

This guide provides quick start instructions for an experienced installer to set up

and operate the DTP3 T 301 transmitter and DTP3 R 301 receiver. These DTP3

digital video Extenders can extend the following up to 330feet (100meters), using shielded twisted pair cabling:

• HDMI digital video signal to 4K@60Hz (4:4:4) (can include embedded digital audio)

• Optional analog audio • USB HID & 2.0

• Bidirectional RS‑232 control • Remote power (receiver to transmitter)

NOTE: Maximum transmission distances vary with resolutions used, cable types, and environment (see the

DTP3T/R301UserGuide at www.extron.com for full specifications).

POWER

1.0 A MAX

12V

DTP3 IN

SIGLINK

RS-232

Tx Rx G

OVER DTP3

SEND

PWR

OFFAUDIO

DEVICES

USB HID

USB 2.0

HDMI

OUTPUTS

POWER

2.8 MAX

12V

DTP3 OUT

SIGLINK

RS-232

Tx Rx G

OVER DTP3

AUDIOHOST

HDMI

OUTPUTS

INPUTS

POWERSTANDBY

Table

Microphone

Camera

Comput

75" Touch Display

CAT6A Cable

up to 330' (100 m)

USB

4K/60

HDMI

4K/60

HDMI

Audi

USB

Extron

SB 33 A 75-80

Sound Bar

Extron

DTP3 R 301

Receiver

Extron

DTP3 T 301

Transmitter

Figure 1. Typical DTP3 T/R 301 Transmitter and Receiver Application

Installation

Turn off and disconnect all equipment power sources and mount the transmitter and receiver Extender units as required. The

units can be mounted in a variety of locations using optional Extron mounting accessories (see www.extron.com to determine

the compatible mounting options).

Rear Panel Connections

POWER

1.0 A MAX

12V

DTP3 IN

SIG LINK

RS-232

Tx Rx G

OVER DTP3

SEND

PWR

OFFAUDIO

DEVICES

USB HID

USB 2.0

HDMI

OUTPUTS

LLLIII MMM KKK

JJJ OOO

POWER

2.8 A MAX

12V

DTP3 OUT

SIG LINK

RS-232

Tx Rx G

OVER DTP3

AUDIO

DTP3 T 301

DTP3 R 301

HOST

HDMI

OUTPUTS

INPUTS

AAA FFF EEEBB

HHCC

NNN

GGG

Figure 2. DTP3 T/R 301 Rear Panel Connectors and Features

Transmitter Features

AHDMI input port (see figure 2 on page 1) — Connect an HDMI cable between this port and the HDMI output

HDMI

port (or DVI port, with an appropriate adapter) of the digital video source. The transmitter also accepts embedded

digital audio on this port.

NOTE: See LockIt™ Lacing Brackets on page 3 to use the included Extron LockIt HDMI Cable Lacing

Bracket to secure the connector to the transmitter for Aand E.

BAudio input connector — If desired, plug an analog audio input into the transmitter via this stereo mini jack.

AUDIO

NOTE: The analog audio input is in addition to the digital audio that may be embedded in the HDMI input.

CUSB Host input port — Connect a USB Type A to B cable between this USB type B port and the USB port of a

HOST

host device.

DOver DTP3 port — Connect a serial RS‑232 signal to this 3.5 mm, 3‑pole captive screw connector for

RS-232

Tx Rx G

OVER DTP3

bidirectional RS‑232 (see Over DTP3 connector port on page 4 to wire the connector).

EHDMI output port — Connect a display to this female HDMI connector for local loop‑through monitoring of the

HDMI

source signal.

FDTP3 OUT (TP) port — Connect one end of a TP cable to this RJ‑45 female connector. Ensure the opposite

DTP3 OUT

SIG LINK

end of this cable is connected to the receiver TP Input port (see I, below).

• Use Extron XTP DTP 22 STP cable for the best performance. At minimum, Extron recommends 22 AWG,

solid conductor, STP cable with a minimum bandwidth of 500 MHz.

• Terminate cables with sheilded connectors to the TIA/EIA‑T568B standard (see DTP3 (TP) port on page 4).

• Limit the use of more than two pass‑through points, which may include patch points, and punch down connectors. If

these pass‑through points are required, use shielded couplers and punch down connectors.

ATTENTION:

• Do not connect these devices to a telecommunications or computer data network.

• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.

Signal LED — Indicates the unit is outputting a DTP3 signal.

Link LED — Indicates a valid link is established between the units on the DTP3 input and output cable.

GPower connector (required, if receiver, I, is not sending power ) — Plug an optional external 12 VDC power

POWER

2.8 A MA

12V

supply into this 2‑pole connector (see Power port on page 4).

ATTENTION:

• Do not connect any external power supplies until you have read the Attention notications in the Power

Supply section of the DTP3 T/R 301 User Guide.

• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section «

Power Supply » du DTP3 T/R 301 User Guide.

HRESET button and LED — This button initiates two levels of reset (see the DTP3 T/R 301 User Guide, at www.extron.com).

Receiver Features

DTP3 IN

SIG LINK

SEND

PWR

OFF

IDTP3 IN (TP) port and Send PWR switch— Connect one end of the TP cable from the transmitter

output connector to this RJ‑45 female connector. Ensure the opposite end of this cable is connected to

the Output RJ‑45 connector on a compatible transmitter.

DTP3 T/R 301 • Setup Guide (Continued)

ATTENTION:

• Do not connect these devices to a telecommunications or computer data network.

• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.

Send Power switch — Set the switch as desired:

OFF (default) — Do not send power. The transmitter must receive power from an optional local power supply.

SEND PWR – Send 48 VDC power across the TP cable to remotely power the transmitter.

NOTE: Remote power to the transmitter is only available if the transmitter is also in the Extron DTP3 series. The

switch should be OFF for any other transmitter type.

Signal LED — Indicates the unit is receiving a valid signal on the DTP3 IN connector.

Link LED — Indicates a valid link is established between the units on the DTP3 cable.

JHDMI Output port (see figure 2 on page 1)— Connect a video display to this HDMI connector.

HDMI

NOTE: See LockIt™ Lacing Brackets on page 3 to use the bracket to secure the connector to the unit.

KAudio Output port— This 5‑pole, 3.5 mm captive screw connector outputs the transmitted, unamplified, line

AUDIO

level analog audio. Connect an audio device, such as an audio amplifier or powered speakers (see Analog

audio output port on page 4 to wire the connector).

LUSB Device ports — The four port hub has female USB Type A connectors; two are HID (keyboard and

USB HID

USB 2.0

mouse only) and two that are USB 2.0 (all USB devices, such as thumb drives and cameras). HID

ports can provide 100mA to power connected peripherals. USB 2.0 ports can provide 500mA. An

external hub can be connected only to a USB 2.0 port and adds to the total system hub count.

MOver DTP3 port — Connect a serial RS‑232 signal to this 3.5 mm, 3‑pole captive screw connector for

RS-232

Tx Rx G

OVER DTP3

bidirectional RS‑232 communication (see Over DTP3 connector port on page 4 to wire the connector).

NPower connector — Plug an external 12 VDC power supply into this 2‑pole connector (see Power port on page 4).

POWER

1.0 A MA

12V

ATTENTION:

• Do not connect any external power supplies until you have read the Attention notications in the Power

Supply section of the DTP3 T/R 301 User Guide.

• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section «

Power Supply » du DTP3 T/R 301 User Guide.

OReset button — This button initiates two levels of reset (see the DTP3 T/R 301 User Guide, at www.extron.com).

LockIt™ Lacing Brackets

Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as follows:

1Plug the HDMI cable into the panel connection.

333

111

555

444

222

2Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt

lacing bracket to be placed over it. The screw does not have to be removed.

3Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten

the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield it fastens to

is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel

elle est attachée est très n et peut facilement être dénudé.

4Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown.

5Hold the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any excess length.

68-3327-50

Rev. A

08 23

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Front Panel Connection and Indicators

SIGNAL

HDCP

HOST

DEVICES

DTP3 R 301

CONFIG

USBINPUT

DDD FFF

SIGNAL

HDCP

HOST

DTP3 T 301

CONFIG

USBINPUT

BBB EEEAAA CCC

Figure 3. DTP3 T/R 301 Front Panel Features

APower LED — The Extender is receiving power, either locally or remotely (via power‑over‑DTP — transmitter only).

BConfiguration port — Connect to this USB mini‑C port (USB 2.0) for product configuration and firmware updates.

CINPUT LEDs (transmitter) — Indicate the status of the HDMI input as follows:

SIGNAL LED — The transmitter is receiving an active HDMI input signal.

HDCP LED — The HDMI signal is HDCP encrypted.

DINPUT LEDs (receiver) — Indicate the status of the DTP3 input as follows:

SIGNAL LED — The receiver is receiving an active HDMI input signal.

HDCP LED — The HDMI signal is HDCP encrypted.

EUSB HOST LED (transmitter) — An active host is connected to the rear panel USB port.

FUSB LEDs (receiver) — Indicate the status of the rear panel USB ports, as follows:

HOST LED — An active host is connected to the rear panel USB HOST port of the transmitter.

Devices LEDs —

1 and 2 LEDs — An active HID device is connected to the rear panel USB port.

3 and 4 LEDs — An active USB 2.0 device is connected to the rear panel USB port.

DTP3 (TP) port Over DTP3 port

Wire color

White‑green

Green

White‑orange

White‑blue

Orange

White‑brown

Brown

Blue

TIA/EIA T

568B

TP Wires

12345678

Pins:

RxTx Gnd

RS-232

Device

RS-232

Tx Rx G

OVER DTP3

Analog audio output port Power port

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

No Ground Here

Tip

Sleeves

Tip

Ring

Tip

Ring

Sleeves

Power Supply

Output Cord

Ridges

Smooth

Captive

Screw

Connector

16 (5 mm) MA

SECTION A–A

Altri manuali Extron electronics Hardware per computer

Extron electronics

Extron electronics WindoWall Pro Series Manuale utente

Extron electronics

Extron electronics DMP 44 LC Manuale utente

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Manuale utente

Extron electronics

Extron electronics DMP Plus Series Manuale utente

Extron electronics

Extron electronics DMP 128 Plus Manuale utente

Extron electronics

Extron electronics Multi-Graphic Processor MGP 464 Manuale utente

Extron electronics

Extron electronics IPL Pro Series Manuale utente

Extron electronics

Extron electronics DVI Output Card Manuale utente

Extron electronics

Extron electronics IPCP Pro PCS1 xi Manuale utente

Extron electronics

Extron electronics Annotator 300 Manuale utente

Extron electronics

Extron electronics DMP 64 Plus Manuale utente

Extron electronics

Extron electronics PIP 422 Manuale utente

Extron electronics

Extron electronics IPCP Pro Series Manuale utente

Extron electronics

Extron electronics Dual Window Multi-Graphic Processor MGP 462 Manuale utente

Extron electronics

Extron electronics MTP 15HD RS Series Manuale utente

Extron electronics

Extron electronics IPCP 505 Manuale utente

Extron electronics

Extron electronics AXP 64 C AT Manuale utente

Extron electronics

Extron electronics Quantum Ultra Series Manuale utente

Extron electronics

Extron electronics Quantum Ultra Series Manuale utente

Extron electronics

Extron electronics EDID 101H 4K PLUS Manuale utente

Extron electronics

Extron electronics XMP 240 C AT Manuale utente

Extron electronics

Extron electronics SC 210 Manuale utente

Extron electronics

Extron electronics Scalable Multi-Graphic Videowall Processors MGP 464W... Manuale utente

Extron electronics

Extron electronics StudioStation 100 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente