FAAC E124 Manuale di istruzioni

Pre-installation Checks

Please ensure that the correct cabling has been installed prior to commissioning of the system, as

incorrect cabling can prevent the unit from operating correctly immediately or after installation.

BUS-2EASY ENCODER and PHOTOCELLS Cable Specification: 2 core 0.5mm2 Multi-Strand Shielded Cable

with the Sheath connected to the Earth at one end. Please do not share BUS-2EASY devices with other DC

Voltage devices as it leads to electrical noise causing interference with the digital data on BUS-2EASY.

Motor Cable Specification: Minimum 2 core 2.5mm2 Multi-Strand Cable for a recommended distance of

10mtrs, further distances are possible but will require thicker cable.

Key Components of E124 Board

Description of Key Components

LCD

SIGNALS AND PROGRAMMING DISPLAY

DL8

“FCA2” STATUS LED

LIMIT SWITCH OPEN

–

IF GATE CLOSED ON

SW4

“+” PROGRAMMING BUTTON

DL9

“FCC2” STATUS LED

LIMIT SWITCH CLOSED

–

IF GATE

CLOSED OFF

SW5

“

” PROGRAMMING BUTTON

DL12

LED FOR BUS

2EASY DEVICE ACTIVE

SW6

“F” PROGRAMMING BUTTON

DL13

LED FOR BUS

2EASY DIAGNOSTICS

SW7

“RESET SW” SOFTWARE RESET BUTTON

DL1

LED

SIGNALING PRIMARY POWER ON

DL1

“IN1” STATUS LED

–

DEFAULT OPEN A

NORMAL STATE OFF

DL19

LED FOR WHEN “SW7” IS PRESSED

DL2

“IN2” STATUS LED

–

DEFAULT OPEN B

NORMAL STATE OFF

DL20

LED SIGNALLING “ALARM”

DL3

“IN3” STATUS LED

–

DEFAULT STOP

NORMAL STATE ON

CONNECTOR FOR CONNECTION OF BUS

2EASY DEVICES

DL4

“IN4” STA

TUS LED

–

DEFAULT FSW OP

NORMAL STATE ON

CONNECTOR FOR TERMINAL BOARD INPUTS

DL5

“IN5” STATUS LED

–

DEFAULT FSW CL

NORMAL STATE ON

CONNECTOR FOR OUTPUT 2 (OUT2)

DL6

“FCA1” STATUS LED

LIMIT SWITCH OPEN

–

IF GATE CLOSED ON

CONNECTOR FOR

TRAVEL LIMITS

DL7

“FCC2” STATUS LED

LIMIT SWITCH CLOSED

–

IF GATE CLOSED OFF

These instructions are to be considered as a rapid guide for installation and to confirm the correct

handing and polarity of the motors. They can also be used to confirm the operating logics before

additional safety devices are fitted to the system as specified by the Risk Assessment undertaken by the

installer. The installer should still familiarise themselves with the full manual and the safety information

contained within. (available at https://www.faac.co.uk/accessories-and-control-boards/control-

boards/for-swing-gates/e124-control-board)

Dip 1

Dip 2

Dip 3

Dip 4

Type

OFF

OPENING

OFF

OPENING

OFF

CLOSING

OFF

CLOSING

OFF

OPENING AND CLOSING

OFF

OPENING AND CLOSING

OPEN PULSE

If no safety devices such as traditional photocells and

Emergency Stop Button fitted, please link the terminals as

above and confirm the as shown above LED’s are lit.

The below shows a typical wiring of a set of photocells

outside across the opening (closing safety) and a set of

photocells inside beyond the arc of the gate (opening and

closing safety) and the STOP circuit linked out and confirming

as shown below

LED

’s are lit.

The following shortened table shows the programming

operations of the dip-switch inside the transmitter and the

receiver of the BUS-2EASY photocells. The full manual

contains the full list.

Leaf 1 Leaf 2 Leaf 1 Leaf 2

Leaf 1 Leaf 2

The function is

displayed only while

the button is pressed

or simple programming of the motor type and logic only

Basic Programming is required as below. The first

parameter that MUST be set is the “CF”. This will then allow correct configuration to proceed. Please note

that until SETUP as been completed the display will show a flashing “50”, which is SETUP requested.

Please note that if you have a mixed system i.e. A S700H/S800H and a S800H ENC or 413 and 418, this will

require the use of Easyboard software. A Windows laptop or Mac Laptop with a Type A to Type B USB lead

will be required. Available to download from https://faac.biz/documents/?drawer=Software*EasyBoard

Please note that for the majority of systems the default power and speed settings will be sufficient to allow

the first setup. These values will generally require further adjustments if force limitation is being used as part

of the safety systems and a new setup should be run after the power settings are changed.

The below in the figure is what should be seen as an example for a double gate that is using encoders.

The above is

the Status references is what will be seen under normal operation, even if the alarm LED is

illuminated. To identify the error the signalling Errors and Alarms procedure should be followed.

The following shows the typical wiring of a Maglock using either OUT 1 or OUT 2

with a relay and separate power

supply

, which are configurable in the Advanced Programming

by holding “F” and “+” together.

The following parameters from Advanced Programming may also

need to be changed if the SETUP continues to fail.

Altri manuali per E124

Indice

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente