Fanimation Palmetto Manuale utente

Questo manuale è adatto per i seguenti modelli

4

Indice

Altri manuali Fanimation Fan

Fanimation

Fanimation ARCHIVE LP3071 Series Manuale utente

Fanimation

Fanimation Air Shadow FB8250B Manuale utente

Fanimation

Fanimation Enigma FP2120 Series Manuale utente

Fanimation

Fanimation Punkah FP720 Series Manuale utente

Fanimation

Fanimation FP8012 series Manuale utente

Fanimation

Fanimation FP4630SN The Zonix Manuale utente

Fanimation

Fanimation Cancun FP8012 220 Series Manuale utente

Fanimation

Fanimation Kute FPD8534 Series Manuale utente

Fanimation

Fanimation Louvre FP1320 Series Manuale utente

Fanimation

Fanimation Bayhill LB270VZ Manuale utente

Fanimation

Fanimation FP7988MB Manuale utente

Fanimation

Fanimation Multimax FP8008CH Manuale utente

Fanimation

Fanimation EIGHTYFOUR LP6827 Series Manuale utente

Fanimation

Fanimation FP4650 Series Manuale utente

Fanimation

Fanimation Centaurus FP4220SN Manuale utente

Fanimation

Fanimation TRIAIRE MAD8514 Series Manuale utente

Fanimation

Fanimation Windpointe MW75 Series Manuale utente

Fanimation

Fanimation FP8003-220 The Benito Manuale utente

Fanimation

Fanimation Andover FP5220 Series Manuale utente

Fanimation

Fanimation Old Havana Series Manuale utente

Fanimation

Fanimation HUGH 44 Manuale utente

Fanimation

Fanimation Edgewood TF600 Series Manuale utente

Fanimation

Fanimation FARGO FP3320 Series Manuale utente

Fanimation

Fanimation The Marea FP8026 Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio

The Palmetto

MODEL NOs: FP601 –5**

OWNER’S MANUAL

READ AND SAVE THESE INSTRUCTIONS

WARNING

DO NOT INSTALL OR USE FAN SYSTEM IF ANY PART IS DAMAGED OR MISSING. THIS

PRODUCT IS DESIGNED TO USE ONLY THOSE PARTS SUPPLIED DESIGNATED

SPECIFICALLY FOR USE BY FANIMATION. SUBSTITUTION OF PARTS OR ACCESSORIES

NOT DESIGNATED FOR USE BY FANIMATION COULD RESULT IN PERSONAL INJURY OR

PROPERTY DAMAGE. CONTACT FANIMATION FOR MISSING OR DAMAGED PARTS.

(888) 567-2055

OR

(317) 733-4113

MAINTENANCE AND BLADE CLEANING

PERIODIC CLEANING IS RECOMMENDED USING A SOFT BRUSH OR LINT FREE CLOTH.

ABRASIVE AND/OR NON-ABRASIVE CLEANING AGENTS ARE NOT REQUIRED AND

SHOULD BE AVOIDED TO PREVENT DAMAGE TO FINISH. ALSO LIGHT DUSTING OF THE

SELECTED BLADE IS RECOMMENDED. A FEATHER DUSTER WILL WORK BEST.

PERIODICALLY TIGHTEN SET SCREWS ON SHAFT ADAPTERS (P608MAC AND P610MAC),

BLADE HUBS TO SHAFT SCREWS AND HUB TO BLADE STEMS.

1. LOCATE POWER

a. POWER IS SUPPLIED BY PURCHASER/CONTRACTOR

b. DISCONNECT POWER SUPPLY AT BREAKER BOX.

c. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY

(P680M**)

d. A SINGLE PHASE 220 TO 240VAC ELECTRICAL FEED LOCATED AT THE CENTER OF THE MOTOR ASSEMBLY

(P680M**)

e. A SINGLE PHASE ELECTRICAL FEED IS REQUIRED

f. MOTOR IS SINGLE SPEED ONLY

g. DO NOT OPERATE WITH ANY SPEED CONTROL

2. INSTALLATION NOTE

a. IT IS RECOMMENDED THAT EACH CEILING MOUNT ASSEMBLY (P680M**, P600S**, AND P600D** IF REQUIRED)

HAVE ¾” PLYWOOD BACKING SECURED TO A STRUCTURAL MEMBER FOR ADEQUATE SUPPORT.

3. MOUNT MOTOR ASSEMBLY OVER POWER SUPPLY TO COVER JUNCTION BOX.

a. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED

b. DRILL PILOT HOLES

c. START 2 SUPPLIED LAG BOLTS WITH WASHER IN THE OUTSIDE HOLES

d. DO NOT COMPLETELY TIGHTEN LAG BOLTS AT THIS TIME

e. CONNECT THE MOTOR WIRES TO THE SUPPLIED LEADS

i. BROWN TO “HOT”

ii. BLUE TO “NEUTRAL”

f. POSITION MOTOR ASSEMBLY OVER THE FINAL TWO PREDRILLED HOLES AND FASTEN WITH REMAINING LAG

BOLTS AND WASHERS

g. SECURE ALL FOUR LAG BOLTS

4. LOCATE POSITION OF EITHER END OR CENTER ASSEMBLY (P600S** OR P600D**)

a. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 9’11” CENTER OF BASE TO CENTER OF BASE OR

b. MAXIMUM DISTANCE FROM MOTOR TO NEXT ASSEMBLY IS 10’5” FROM OUTSIDE EDGE OF BASE TO OUTSIDE

EDGE OF BASE.

c. MARK FOUR MOUNTING HOLE POSITIONS AS REQUIRED

d. DRILL PILOT HOLES

e. MOUNT NEXT ASSEMBLY IN DESIRED LOCATION AND TIGHTEN ALL FOUR LAG BOLTS SECURELY

f. MEASURE DISTANCE FROM INSIDE EDGE OF COUPLER ADAPTER TO INSIDE EDGE OF COUPLER ADAPTER TO

DETERMINE LENGTH OF ROTATING SHAFT (TUBE108**)

g. CUT ROTATING SHAFT (TUBE108**) TO MEASURED LENGTH.

h. ON SECOND ASSEMBLY LOOSEN THE TWO LAG BOLTS ON THE INSIDE EDGE OF THE BASE ENOUGH TO LEAN IT

BACK.

i. INSTALL DESIRED NUMBER OF HUB ASSEBMLIES (P606**) ON THE ROTATING SHAFT (TUBE108**)

j. SPACE HUBS (P606**) ALONG ROTATING SHAFT AS DESIRED AND SECURE WITH SET SCREWS

k. INSERT ROTATING SHAFT IN THE MOTOR END COUPLER AND TIGHTEN SET SCREW.

l. LEAN BACK SECOND ASSEMBLY AND INSERT ROTATING SHAFT (TUBE108**) INTO THE COUPLER ADAPTER.

m. TIGHEN LAG BOLTS SECURELY ON THE BASE

n. TIGHTEN SET SCREW ON COUPLER ADAPTER.

5. IF YOU ARE INSTALLING ADDITIONAL SECTIONS REPEAT STEP 4 FOR EACH

a. BE SURE THAT THE MIDDLE ASSEMBLIES ARE P600D** AND THE FINAL ASSEMBLY IS THE P600S**

6. INSERT BLADE ASSEMBLY STEM INTO HUB ASSEMBLIES AND SECURE WITH SETSCREWS.

a.

7. CHECK THAT HUBS, BLADE STEMS, BLADES AND ROTATING SHAFT (TUBE108**) SETSCREWS ARE SECURE

8. RESTORE POWER TO SYSTEM.