Fanvil i32V Manuale utente
www.fanvil.com
Video Door Phone
Quick Installation Guide
1) Panel
Device size
Package Contents
1
Physical specification
2
i32V Video Door Phone
Quick Installation Guide
Connector
Mounting Template
195 x 120 x 34 (mm)
Speaker
Camera
RFID area
MIC
1
www.fanvil.com
Video Door Phone
Quick Installation Guide
RFID Cards Screw and tool
IR LED
2) Interface description
①
②
③
④
⑤
⑥⑦⑧
⑨
⑩
2
1
2
3、5
4、6
7
10
11
Ethernet interface: standard RJ45 interface, 10/100M adaptive, it is recommended to
use five or five types of network cable
Description
Serial
number
Power interface: 12V/1A input left positive, right grounded
Two sets of short-circuit input detection interfaces: for connecting switches, infrared probes,
door magnets, vibration sensors and other input devices
Two sets of short-circuit output control interface: used to control electric locks, alarms, etc.
Wiegand interface
Two sets of door magnetic detection
Recording output interface: Mix the device and the sound of the far-end call. One is the
recording signal line, and the other is the ground line (be sure to ground the line,
otherwise there will be noise)
External active speaker interface: external active speakers for audio power amplification.
One is the audio signal line, and the other is the ground line (be sure to ground the line,
otherwise there will be noise)
JP1 jumper
8、9
12
JP1 Jumper
There are two modes for power supply of electric-lock as shown in the picture below.
(The default is “ Passive Mode: ”).
Passive Mode: When the electric-lock starting current is more than 12V/500mA, need to use the external
drive mode, the electric lock interface for short circuit output control.
Open the rear case of the device, there is a row of terminal blocks for connecting the power supply,
electric lock control, etc. The connection is as follows:
12V+
S1-IN
S1-OUT
12V
NC1
COM1
NO1
S2-IN
S2-OUT
NC2
COM2
VCC_OUT
NO2
GND
D0
D1
LED
Buzzer
GND
DET IN2
GND
MIC_SPK
GND
Line OUT
GND
DET IN1
Line OUT
CN11 CN2 CN5 CN4 CN3 CN10 CN9
Active Mode : When the electric-lock starting current is less than 12V/500mA, can use the internal
drive mode, the electric lock interface is 12V DC output.
3) Wiring instructions:
Driving Mode Electric-lock Mode
Active Passive No electricity
when open Electrify
when open
√
√
√
√√
√
JP1
Jumper Connections
3
NO: Normally Open Contact
COM: Common Contact
NC: Normally Close Contact
√ √
There are two methods as shown below to search the device.
Method 1:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the device and find the
IP address.
（Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe ）
Method 2:
Long press DSS key for 10 seconds(after power-on for 30 seconds), and when the speaker beeps
rapidly, press DSS key again quickly, the beeps stop ,the intercom will report the IP address by itself.
4
√ √
In addition, device provides the device surface DSS key operation to switch IP address acquisition
mode:
Long press the DSS key for 10 seconds, to be issued by the speaker Beep, and then press the DSS
key three times, the beep stops. Wait 10 seconds, after the success of the system automatically
broadcast the current IP address.
Wall-mounted:
1) Use built-in screw tool to remove the surface shell;
2) Based installation dimensions, mounting hole in the wall to draw, use an electric drill holes lay;
3) The white rubber plugged into the wall and the bottom fixed with screws to the wall;
4) After connecting the power cord and network cable, screw the surface shell fixed.
Installation Diagram
3
Searching Door Phone
4
192.168.1.128
Step 1: Log in the door phone
Input IP address (e.g. http://192.168.1.128) into address bar of PC’s web browser.
The default user name and password are both admin.
Step 2: Add the SIP account.
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.
Step 3: Setting DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Hot Key
Number 1: The DSS Key will dial to this Number 1.
Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
Line: Working line
Subtype: Speed dial
5
IP Door Phone Setting
5
Step 4: Door Phone Setting
RFID Card
Step 1: Go to EGS Access → Enter the Name and ID Number (Only Front 10 yards)
→ Press Add to Access Table.
Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.
Remote Password
Step 1: Go to EGS Setting → Features → Set Remote Password (The default is “*”).
Step 2: To answer the call made by visitor via SIP phone, press the “*” key to unlock
the door the visitor.
6
Door Unlocking Setting
6
Fanvil Technology Co., Ltd
Email:[email protected]Tel:0755-2640-2199
Add: 4F, Block A, Building 1#, GaoXinQi Hi-Tech Park (Phase-II),
67th District, Bao'An, Shenzhen, China
Fax:0755-2640-2618
P.C:518101
Indice
Altri manuali Fanvil Sistema di interfono
Fanvil
Fanvil i56A Manuale utente
Fanvil
Fanvil i55A Manuale utente
Fanvil
Fanvil i20S Manuale utente
Fanvil
Fanvil i10S Manuale utente
Fanvil
Fanvil i16V Manuale utente
Fanvil
Fanvil A10 Manuale utente
Fanvil
Fanvil i10 Manuale di installazione e d'uso
Fanvil
Fanvil i51W Manuale utente
Fanvil
Fanvil i10V Manuale di installazione e d'uso
Fanvil
Fanvil i51W Manuale utente
Fanvil
Fanvil i55A&i55A-Z Manuale utente
Fanvil
Fanvil i20 Manuale utente
Fanvil
Fanvil i20S Manuale utente
Fanvil
Fanvil I20-T Manuale utente
Fanvil
Fanvil I20-T Manuale utente
Fanvil
Fanvil i33V Manuale utente
Fanvil
Fanvil i16S Manuale utente
Fanvil
Fanvil i20S IP DoorPhone Manuale utente
Fanvil
Fanvil i23 Manuale utente
Fanvil
Fanvil Y50r-Y Manuale utente
