Feig Electronic ID ISC.M02.M8 Manuale utente

INSTALLATION MANUAL

final – public (B)

2020-06-03 – M02M8-IM-e_02.doc

ID ISC.M02.M8

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 2 of 16 M02M8-IM-e_02.doc

Note

Copyright by

FEIG ELECTRONIC GmbH

Lange Strasse 4

D-35781 Weilburg

Tel.: +49 6471 3109-0

http://www.feig.de

With the edition of this document, all previous editions become void. Indications made in this manual may be

changed without previous notice.

The reproduction, distribution and utilization of this document as well as the communication of its contents to

others without express authorization is prohibited. Offenders will be held liable for the payment of damages.

Composition of the information in this document has been done to the best of our knowledge. FEIG

ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this

manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,

despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.

The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC

GmbH does not give any guarantee promise for perfect function in cross environments and does not give

any guaranty for the functionality of the complete system which incorporates the subject of this document.

FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed

with components and testing methods for a level of reliability suitable for use in or in connection with surgical

implants or as critical components in any life support systems whose failure to perform can reasonably be

expected to cause significant injury to a human. To avoid damage, injury, or death, the user or application

designer must take reasonably prudent steps to protect against system failures.

FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this

document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH

does not convey any license under its patent rights nor the rights of others.

All brand names, trademarks or logos are property of their respective owners.

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 3 of 16 M02M8-IM-e_02.doc

Content

ID ISC.M02.M8 1

1Safety Instructions / Warning - Read before start-up ! 4

2Performance Characteristics of the ID ISC.M02.M8 Reader Module 5

2.1Performance Characteristics...................................................................................5

2.2Available module ......................................................................................................5

2.3Available Accessories..............................................................................................5

3Installation and wiring 6

3.1Dimensions ...............................................................................................................6

3.2Wiring.........................................................................................................................7

3.2.1Supply voltage............................................................................................................7

3.2.2RS232-LVTTL-Interface (3,3V)...................................................................................8

3.2.3Connection of the external antennas..........................................................................9

3.3Installation notes ....................................................................................................10

3.3.1Mounting...................................................................................................................10

3.3.2Influence...................................................................................................................10

3.3.3EMC effects on cables..............................................................................................11

3.3.4EMC effects from magnetic fields.............................................................................11

4Technical Data 12

51.Approvals 14

5.11.1.Europa (CE)............................................................................................................14

5.21.2.USA (FCC) and Canada (IC)..................................................................................15

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 4 of 16 M02M8-IM-e_02.doc

1 Safety Instructions / Warning - Read before start-up !

The device may only be used for the intended purpose designed by for the

manufacturer.

The operation manual should be conveniently kept available at all times for each user.

Unauthorised changes and the use of spare parts and additional devices which have not

been sold or recommended by the manufacturer may cause fire, electric shocks or

injuries. Such unauthorised measures shall exclude any liability by the manufacturer.

The liability-prescriptions of the manufacturer in the issue valid at the time of purchase

are valid for the device. The manufacturer shall not be held legally responsible for

inaccuracies, errors, or omissions in the manual or automatically set parameters for a

device or for an incorrect application of a device.

Repairs may only be executed by the manufacturer.

Installation, operation, and maintenance procedures should only be carried out by

qualified personnel.

Use of the device and its installation must be in accordance with national legal

requirements and local electrical codes .

When working on devices the valid safety regulations must be observed.

The reader module is a limited module. The HF Reader IC has no internal shielding. The

module is designed for installation in electronic devices. (e.g. printers, terminals, hand

scanners, etc.) Care must be taken to ensure that no switching power supply, oscillator

or high current lines are routed directly along the module. Or located under the module.

Only the antennas, mentioned in the manual, may be used. The cable length to the an-

tenna is limited to 1m. Take care that the PCB design in the host environmentis is EMC

compliant.

Special advice for carriers of cardiac pacemakers:

Although this device doesn't exceed the valid limits for electromagnetic fields you

should keep a minimum distance of 25 cm between the external antenna and your cardi-

ac pacemaker and not stay in an immediate proximity of the device respective the an-

tenna for some time.

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 5 of 16 M02M8-IM-e_02.doc

2 Performance Characteristics of the ID ISC.M02.M8 Reader Module

2.1 Performance Characteristics

The ID ISC.M02.M8 reader module is designed for reading and writing passive transponders, so-

called “Smart Labels”, with an operating frequency of 13.56 MHz according to the ISO15693

standard. It is suitable for any application in which short read ranges and small reader dimensions

are required.

The module has an integrated antenna multiplexer. Up to 8 external antennas can be connected.

2.2 Available module

The following reader types are available:

Module type Description

ID ISC.M02.M8 1 x Reader module ID ISC.M02.M8

Table 1: Available module version

2.3 Available Accessories

Tab. 1 Available Accessories and spare parts

Part Number Part name Description

3674.000.00 ID ISC.ANT40/30-U.FL-A

50 Ohm Antenna with U.FL-connector for the connection

to the ID CPR60

Dimensions: 40 mm x 30 mm

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 6 of 16 M02M8-IM-e_02.doc

3 Installation and wiring

3.1 Dimensions

Fig. 1 shows the dimensions of the ID ISC.M02.M8 Reader Module in mm.

5±0,3 65±0,3

80±0,3

5±0,3

45±0,3

50±0,3

16,5±0,3

4±0,3

Ø4,2±0,1

2,5±0,6

14,1±0,3

87±0,3

2,54

Fig. 1: Dimension of the Readermodul ID ISC.M02.M8

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 7 of 16 M02M8-IM-e_02.doc

3.2 Wiring

Figure 1 and Table 2 show the pin assignments for Terminal X9. The pin connector is designed for

flat cable connection using a 5 pin multipoint socket connector type MTA 100 company AMP.

Pin-No. Function Description

1 GND ** GND

2 TxD RS232-LVTTL – Send data

3 Vin * + 24VDC

4 RxD RS232-LVTTL – Receive data

5 GND ** GND

* Use only regulated DC power supplies !

Table 2: Pin Assignment of the multipoint connector X9

Note:

A wrong polarity of the DC voltage will destroy the reader

3.2.1 Supply voltage

The reader ID ISC.M02.M8 has to supplied by a limited power supply (e.g. NEC Class 2/LPS

power supply) according IEC EN 60950, only.

If switching power supplies are used with the module, be sure that there is adequate filtering.

Noise from the power supply can result in a reduction of the read/write range of the module.

The cable length from the power supply should be as short as possible, and should in any case not

exceed 1 m.

Note:

A wrong polarity of the DC voltage will destroy the reader

Supply voltages outside the specifications may destroy the device.

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 8 of 16 M02M8-IM-e_02.doc

3.2.2 RS232-LVTTL-Interface (3,3V)

The length of the cable to the RS232 LVTTL interface should be kept as short as possible, and

must in any case not exceed 1 m.

The transmission parameters for the interface can be software-configured.

Table 3 shows the standard parameters for the RS232 interface.

Parameter Default Setting

Baudrate 38400 bit/s

Number of Data bits 8

Parity Even

Number of Stop bits 1

Table 3 Default parameter of the RS232 LVTTL

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 9 of 16 M02M8-IM-e_02.doc

3.2.3 Connection of the external antennas

Up to 8 external antennas can be connected.

For the connection of the external antennas 8 antenna connectors (X1..X8 respectively A1..A8) are

available.

The connector type is U.FL-R-SMT from the company Hirose. .

Alternatively a 16pin connector can be used for the connection of the antennas.

Figure 1 shows the pin assignment.

Figure 1: Antenna connector‘s

Note:

A coaxial cable, U.FL-LP-088, is used to connect the antenna. The antenna cable should

be no longer than 1 m. The use of other cable length are possible after consulting the

manufacturer.

The input impedance for the antenna must be calibrated to a value of









3°).

A not correct tuned antenna can destroy the reader.

The optimum working quality of the antenna should be in a range of QB = 10...20.

For measuring the working quality the antenna must be connected with a 50



-source,

e.g. a network analyzer or a frequency generator

When connecting an antenna, ensure that it does not exceed the permissible limits pre-

scribed by the national regulations for radio frequency devices.

The ultraminiatur coax connector can be used for up to about 20 connection cycles. For

the disconnection the „Extraction Tool“ must be use according to the recommendation

from the manufacturer.

IDENTIFICATION Installation ID ISC.M02.M8

FEIG ELECTRONIC GmbH Page 10 of 16 M02M8-IM-e_02.doc

3.3 Installation notes

The reader module has been designed for the installation in a device.

3.3.1 Mounting

The reader module can be mounted by using 4mm (M4) screws.

Component side: the maximum head diameter should not increase more than 8mm.

Preferred no metallic screws should be used (DIN7985).

Alternatively internal hexagon screws can be used (DIN 912).

Component underside: conductive materials can have a diameter of 6mm.

Non-conductive materials can have a diameter of up to 10mm.

The mounting orientation of the reader module is arbitrary. The component side on the top is

the preferred orientation.

Check the planed mounting place first for suitability.

3.3.2 Influence

Be aware of the following possible environmental factors when installing the module into another

device :

Effects from nearby metal objects

Detuning of the integrated antenna

Impaired propagation of the antenna’s magnetic field

EMC effects on cables

Impaired communication between reader and transponder

EMC effects from magnetic fields

Impaired communication between reader and transponder

Indice

Altri manuali Feig Electronic Unità di controllo

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-B Manuale utente

Feig Electronic

Feig Electronic cVEND plug Manuale utente

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Manuale utente

Feig Electronic

Feig Electronic ID ISC.LRM1002-E Manuale per l'uso e la cura

Feig Electronic

Feig Electronic OBID i-scan D ISC.MU02.02 Manuale utente

Feig Electronic

Feig Electronic ID ISC.MU02.02-CU Manuale utente

Feig Electronic

Feig Electronic ID MAX.U1002 Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.PRH102-B Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02.M8-B Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LR200 Series Manuale utente

Feig Electronic

Feig Electronic ID ISC.MU02.02 Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-A Manuale utente

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02 Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LRM2500-B Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.MAT-A Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02 Manuale utente

Feig Electronic

Feig Electronic ID ISC.MRMU102-A Manuale utente

Feig Electronic

Feig Electronic TST WUI Manuale di installazione

Feig Electronic

Feig Electronic OBID i-scan ID ISC.M02.M8-B Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.PR101-USB Manuale utente

Feig Electronic

Feig Electronic OBID i-scan ID ISC.LR2500-A Manuale utente

Feig Electronic

Feig Electronic OBID ID RWA02.ABCD Series Guida utente

Feig Electronic

Feig Electronic ID ISC.ANT.U500/270 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente