FELIXprinters Pro Series Manuale di installazione e d'uso

How to remove stuck filament in extruder

27 September

2019

Revision 0

FELIX Pro 3

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Introduction

1Introduction

This manual describes how to remove stuck filament in the extruder assembly.

If you are unable to continue or have any questions, you can check at the support section of our website or you can

This manual only shows the left extruder. For the right extruder it is exactly the same as they are symmetric to each

other with exception to a few details.

Website: www.felixprinters.com/support

Email: [email protected]m

Telephone: +31 (0)30 30 31 387

Address: Zeemanlaan 15, 3401MV IJsselstein, The Netherlands

Kind regards,

FELIXprinters

Table of Contents

1Introduction.............................................................................................................................................................................. 1

2Remove cap above hot-end.................................................................................................................................................. 2

3Take off extruder assembly .................................................................................................................................................. 3

4Re-assemble again.................................................................................................................................................................. 8

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Remove cap above hot-end

2Remove cap above hot-end

Normally filament can get stuck above the hot-end. This can easily be fixed by loosening the front cover of the

extruder

Remove the screw and pull out the cover part. You can see the filament or perhaps a piece that got stuck. Please

remove it and reverse assembly.

To ease removal of the filament in some occasions it is required to open the front door and take out the hot-end.

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Take off extruder assembly

3Take off extruder assembly

In case the filament gets stuck above the extruder drive wheel more disassembly is required.

Loosen bolt with 2.5mm allen key

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Take off extruder assembly

Remove front bolt with 3mm allen key

Slide off extruder assembly and move the heated bed upwards, so the extruder can rest on it.

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Take off extruder assembly

Let extruder assembly rest on the table and prevent strain on wires.

If extruder guidance cap is not yet removed first inspect there.

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Take off extruder assembly

Remove filament detection and extruder arm. First remove circlip

Compress the spring package, to easily slide off extruder arm. Turn clockwise

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Take off extruder assembly

Slide off filament arm

Loosen two screws and carefully take out the extruder arm without the filament detection sensor.

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Re-assemble again.

Loosen the screw with a M2.5 screw.

Open up the assembly and remove any filament.

4Re-assemble again.

Put back together the filament detection again.

Put back the small cover. Push the cap down while fixing it.

How to remove stuck filament

in extruder

27 September 2019

FELIX Pro 3

www.FELIXprinters.com

Re-assemble again.

Slide on the filament detection back again, with spring.

Uncompress the spring again

Place back circlip

Slide the extruder assembly back again. While doing this take note of the small push arms and the lever mechanism.

Now fix the extruder again.

If you are unable to continue or have any questions, you can check at the support section of our website or you can

Website: www.felixprinters.com/support

Email: [email protected]m

Telephone: +31 (0)30 30 31 387

Address: Zeemanlaan 15, 3401MV IJsselstein, The Netherlands

Kind regards,

FELIXprinters

Altri manuali per Pro Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali FELIXprinters Stampante 3D

FELIXprinters

FELIXprinters FELIX Tec 4.1 Manuale utente

FELIXprinters

FELIXprinters Tec 4 Manuale utente

FELIXprinters

FELIXprinters FELIX Pro 3 Touch Manuale utente

FELIXprinters

FELIXprinters Pro 2 Touch Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale per l'uso e la cura

FELIXprinters

FELIXprinters FELIX One Manuale utente

FELIXprinters

FELIXprinters Tec 4 Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale operativo

FELIXprinters

FELIXprinters FELIX Pro 2 Manuale utente

FELIXprinters

FELIXprinters Felix Pro 1 Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale utente

FELIXprinters

FELIXprinters Felix 2.0 Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale di installazione e d'uso

FELIXprinters

FELIXprinters Pro L Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale di installazione e d'uso

FELIXprinters

FELIXprinters Pro Series Manuale per l'uso e la cura

FELIXprinters

FELIXprinters Felix Pro 1 Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale per l'uso e la cura

FELIXprinters

FELIXprinters 3 Series Manuale utente

FELIXprinters

FELIXprinters Pro Series Manuale utente

FELIXprinters

FELIXprinters FELIX Pro 2 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente