FieldServer Canatal Satchnet Driver FS-8700-59 Nota di rilascio

a Sierra Monitor Company

APPLICABILITY & EFFECTIVITY

Effective for all systems manufactured after May 1, 2001

Instruction Manual Part Number FS-8700-59

3/13/03

Driver Manual

(Supplement to the FieldServer Instruction Manual)

FS-8700-59 CanatalSatchnet Driver

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Table of Contents

TABLE OF CONTENTS

1. Canatal Satchnet Protocol Driver Description...................................................................................................................1

2. Hardware/Software.................................................................................................................................................................1

2.1 Supplied by FieldServer Technologies for this driver.............................................................................................1

2.2 Provided by user.............................................................................................................................................................1

3. Hardware Connections...........................................................................................................................................................2

4. Configuring the FieldServer as a Canatal Satchnet Protocol Driver Client..................................................................3

4.1 Data Arrays.....................................................................................................................................................................3

4.2 Client Side Connections................................................................................................................................................4

4.3 Client Side Nodes...........................................................................................................................................................4

4.4 Client Side Map Descriptors........................................................................................................................................5

4.4.1 FieldServer Specific Map Descriptor Parameters............................................................................................5

4.4.2 Driver Specific Map Descriptor Parameters.....................................................................................................5

4.4.3 Timing Parameters................................................................................................................................................5

4.4.4 Map Descriptor Example .....................................................................................................................................6

4.4.5 Map Descriptor Example 2..................................................................................................................................7

5. Configuring the FieldServer as a Canatal Satchnet Protocol Driver Server.................................................................8

5.1 Data Arrays.....................................................................................................................................................................8

5.2 Server Side Connections...............................................................................................................................................9

5.3 Server Side Nodes..........................................................................................................................................................9

5.4 Server Side Map Descriptors......................................................................................................................................10

5.4.1 FieldServer Specific Map Descriptor Parameters..........................................................................................10

5.4.2 Driver Specific Map Descriptor Parameters...................................................................................................10

5.4.3 Timing Parameters..............................................................................................................................................10

5.4.4 Map Descriptor Example ...................................................................................................................................11

6. Driver Notes...........................................................................................................................................................................12

6.1 Canatal Device Data Tables .......................................................................................................................................12

6.2 Troubleshooting............................................................................................................................................................14

7. Version Control..............................................................................................................................................................15

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page

1. Canatal Satchnet Protocol Driver Description

The Canatal Satchnet Protocol Driver allows the FieldServer to transfer data to and from devices

over either RS-232 or RS-485 using Canatal Satchnet Protocol Driver protocol. The FieldServer

can emulate either a Server or Client.

This driver provides support for the Canatal Corporation implementation of the “Satchwell

Network” protocol.

The Canatal Satchnet Protocol Driver can act as a Master.

•Any Satchnet device on any serial port (P1-P8, R1 & R2 on the FS-B40 Series, serial port

on the FS-B20 series) can be polled.

•Data from Series 2, 4, 5, 6, 9 devices can be polled.

•Data from any 'Table' can be read.

•Data in 'Tables' with write permission can be written by the driver.

•The driver can read/write Bit, Byte, Swapped Integer, Word, BCD and Float Data.

The Canatal Satchnet Protocol Driver can act as a (passive) server.

•The driver can be polled by a Satchnet Master and return data from the FieldServer's data

arrays.

•The driver can emulate Series 2,4,5,6,9 devices.

•All 'Tables' can be read / written.

2. Hardware/Software

2.1 Supplied by FieldServer Technologies for this driver

RS-485 connection adapter

Driver Manual.

2.2 Provided by user

Canatal Device

UTP or similar cable with RJ11 adapter.

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page

3. Hardware Connections

The FieldServer is connected to the as shown below.

Configure the Canatal Driver according to manufacturer’s instructions.

Canatal Corporation Inc. have specified the following data with respect to

interconnecting cables.

Interconnecting Cable Characteristics

The interconnecting cable may be composed of twisted or untwisted pair (flat cable)

possessing the characteristics below. Conductor Size: The interconnecting cable shall be

composed of two wires of a 24 AWG or larger conductor for solid or stranded copper

wires, or for non-copper conductors with sufficient size to yield a DC wire resistance not

to exceed 30 ohms per 1000 feet per conductor.

•Mutual Pair Capacitance: The capacitance between one wire in the pair to the

other wire shall not exceed 20 picofarads per foot and the value shall be

reasonably uniform over the length of the cable.

•Stray Capacitance: The capacitance between one wire in the cable to all others in

the cable sheath, with all others connected to ground shall not exceed 40

picofarads per foot and shall be reasonably uniform over the length of the cable.

•Pair-to-Pair Balanced Crosstalk: The balanced crosstalk from one pair of wire to

any other pair in the same cable sheath shall have a minimum value of 40

decibels of attenuation measured at 150 kilohertz.

•

An interconnecting cable meeting these specifications will result in a transmission line

with a nominal characteristic impedance in the order of 100 ohms to frequencies greater

than 100 kilohertz and a DC series loop resistance not exceeding 240 ohms.

CANATAL

FieldServer

BLUE (PIN1)

ORANGE/WHITE

(PIN2)

BROWN BLUE

ORANGE/WHITE

GREEN

(PIN3)

SERIAL PORT

NOTE:

SET JUMPER 16, 17 AND 18 ON THE BOARD TO POSITION 2-3.

CAT 5

ETHERNET CABLE

Manual Canatal FieldServer Connection

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page

4. Configuring the FieldServer as a Canatal Satchnet Protocol Driver Client

For a detailed discussion on FieldServer configuration, please refer to the Configuration Manual for

the FieldServer. The information that follows describes how to expand upon the factory defaults

provided in the configuration files included with the FieldServer (See “.csv” files on the driver

diskette).

This section documents and describes the parameters necessary for configuring the FieldServer as a

master, configured to communicate with a Canatal Satchnet Protocol Driver Server ( a passive

Canatal device).

The configuration file tells the FieldServer about its interfaces, and the routing of data required. In

order to enable the FieldServer for Canatal Satchnet Protocol Driver communications, the driver

independent FieldServer buffers need to be declared in the “Data Arrays” section, the destination

device addresses need to be declared in the “Client Side Nodes” section, and the data required from

the servers needs to be mapped in the “Client Side Map Descriptors” section. Details on how to do

this can be found below.

Note that in the tables, * indicates an optional parameter, with the bold legal value being the

default.

4.1 Data Arrays

Section Title

Data_Arrays

Column Title Function Legal Values

Data_Array_Name Provide name for Data Array Up to 15 alphanumeric

characters

Data_Format Provide data format. Each data array can only

take on one format. FLOAT, BIT, UInt16, SInt16,

Packed_Bit, Byte,

Packed_Byte, Swapped_Byte

Data_Array_Length Number of Data Objects. Must be larger than

the data storage area required for the data

being placed in this array.

1-10,000

Example

// Data Arrays

Data_Arrays

Data_Array_Name, Data_Format, Data_Array_Length

DA_AI_01, UInt16, 200

DA_AO_01, UInt16, 200

DA_DI_01, Bit, 200

DA_DO_01, Bit, 200

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page

4.2 Client Side Connections

Section Title

Connections

Column Title Function Legal Values

Port Specify which port the device is

connected to the FieldServer FS x40: P1-P8, R1-R2

FS x20: P1-R2

Baud Specify baud rate 1200

Parity Specify parity Even

Data_Bits Specify data bits 7

Stop_Bits* Specify stop bits 1

Protocol Specify protocol used Canatal, Satchnet

Handshaking* Specify hardware handshaking RTS, RTS/CTS, None

Poll Delay* Time between internal polls 0-32000 seconds

default 1 second

Example

// Client Side Connections

Connections

Port, Baud, Parity, Protocol, Data_bits, Stop_bits,

R1, 1200, Even, Canatal, 7, 1,

4.3 Client Side Nodes

Section Title

Nodes Column Title Function Legal Values

Node_Name Provide name for node Up to 32 alphanumeric characters

Node_ID Address of physical server node

(Canatal device address) 1-63

Protocol Specify protocol used Canatal, Satchnet

Port Specify which port the device is

connected to the FieldServer FS x40: P1-P8, R1-R2

FS x20: P1-R2

Example

// Client Side Nodes

Nodes

Node_Name , Node_ID, Protocol, Port

Conditioner1, 1, Canatal , R1

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page

4.4 Client Side Map Descriptors

4.4.1 FieldServer Specific Map Descriptor Parameters

Column Title Function Legal Values

Map_Descriptor_Name Name of this Map Descriptor Up to 32 alphanumeric characters

Data_Array_Name Name of Data Array where data is to be

stored in the FieldServer One of the Data Array names from

“Data Array” section above

Data_Array_Location Starting location in Data Array 0 to maximum specified in “Data

Array” section above

Function Function of Client Map DescriptorRDBC, WRBC, WRBX

4.4.2 Driver Specific Map Descriptor Parameters

Column Title Function Legal Values

Node_Name Name of Node to fetch data from One of the node names specified in

“Client Node Descriptor” above

Length Length of Map Descriptor 1 -1000 ( Maximum value is

dependent on the values of

Cana_Series and Cana_table. For

more information see section 6.1

Address This term is used to refer to the offset into the

Canatal device data table.

Each table first element is addressed as zero,

the 2nd elementas 1 etc.

The address & length must not exceed the

maximum length of he table being addressed.

0,1,2,3 ...

Protocol Specific

Parameters

Cana_Series Refers to the Canatal Corporation Inc. device

series number. Although different series of

equipment have similar tables with similar

contents they are not all the same, the

contents may vary and the data formats do

vary.

2,4,5,6,9

Cana_Table This is the data table in the device you wish

to read. Non zero integers. Legal values

may be obtained by reading section

6.1.

Cana_Format * Used to over-ride the default data storage

method the driver assigns to the table. This

paramater may be required when reading data

from a table with midex data formats. See

section 6.1 to identify which table have

mixed data formats and what the default type

the driver allocates to the table.

Bype, BCD, BCD4, Float, Word,

Percent, Swap_int.

4.4.3 Timing Parameters

Column Title Function Legal Values

Scan_Interval Rate at which data is polled >0.1s

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page 6

4.4.4 Map Descriptor Example

In this example two map descriptors are provided. The first reads Device 11 ( a Series 2 device) and obtains the Alarm Table. The second map descriptor reads

Device 23 ( a series 9 device) and reads the Cooling analog output (2nd element of table 10).

Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Address, Length, Cana_Series, Cana_table, Scan_Interval

DEV11_ALMS ,ALARMS ,220 , rdbc ,DEV11 , 0 ,19 , 2 ,11 , 1.0s

DEV23_COOL ,ANA_OUT ,0 , rdbc ,DEV23 , 1 ,1 , 9 ,10 , 1.0s

You need to know the series

of the device you are polling

and table number of the table

that contains the data of

interest.

Read section 6.1 for more

information or read the

vendor product literature.

Any name that is

meaningful to you.

The driver validates

map descriptors and

reports errors

referring to the map

descriptor name.

The data arrays are defined in the

Data_Arrays part of the CSV. Based on

these exampled the array called ALARMS

should be a byte or integer array as

alarms have the value 0,1 or 2 (acked) and

it must be at least 239 (220+19) elements

in size.

The array ANA_OUT is probably a

FLOAT and should have at least 1 element

in size.

These map

descriptors generate

read polls on a

continuous basis.

This is the offset

into the table being

polled.

Determine the offset

you should use by

reading the Canatal

International

Corporation Inc.

Product Literature.

The first element

from table 11 will

be placed in element

220 (the 221st

element) of the array

ALARMS.

The node names

point the driver at a

Node definition

which specifies a

port and a device

address.

The number of items

being read. Not the

number of bytes

being read.

The polls will ocur

every second.

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page 7

4.4.5 Map Descriptor Example 2

In this example two map descriptors are provided. They both read table 16 of a series 9 device. You will see though that the 2nd map descriptor has an extra

keyword to override the default format. Read section 6.1 form more information on default data formats.

// Reads elements 1 through 7from table 5 in a series 9 device. According to the product specification the 8th element is stored using a different format and thus

using this map descriptor to read mixed data type will produce unexpected results.

Map_Descriptors

Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Address, Length, Cana_Series, Cana_table, Scan_Interval

TABLE05_1 ,TBL05_DATA ,0 , rdbc , DEV11 , 1 , 6 , 9 , 5 , 1.0s

// Reads the Boiler Limit Time (Offset 10) from table 5 in a series 9 device According to the product specification the Boiler Limit Time is stored as a Swapped

Integer. The Default format this driver uses for the table is Byte.

Map_Descriptors

Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name, Address, Length, Cana_Series, Cana_table, Cana_format, Scan_Interval

TABLE05_2 ,TBL05_DATA , 0 , rdbc , DEV11 , 7 , 1 , 9 , 5 , swap_int , 1.0s

This parameter over-

rides the

default data type. It is only

required if you need to over-

ride the driver's default.

Any name that is

meaningful to you.

The driver validates

map descriptors and

reports errors

referring to the map

descriptor name. With the offset equal to zero the data

is placed in the array element equal to

the address.

The offset is added to the address

when determining the element of the

data array to be used for storage.

This is the offset of the

Boiler Limit Time in Table 5.

FS-8700-59 Canatal Sachnet Driver Manual

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042

Visit our website: www.fieldserver.com E-mail: support@fieldserver.com

Page 8

5. Configuring the FieldServer as a Canatal Satchnet Protocol Driver Server

For a detailed discussion on FieldServer configuration, please refer to the instruction manual for the

FieldServer. The information that follows describes how to expand upon the factory defaults

provided in the configuration files included with the FieldServer (See “.csv” files on the driver

diskette).

This section documents and describes the parameters necessary for configuring the FieldServer to

communicate with a Canatal Satchnet Protocol Driver Client (Master)

The configuration file tells the FieldServer about its interfaces, and the routing of data required. In

order to enable the FieldServer for Canatal Satchnet Protocol Driver communications, the driver

independent FieldServer buffers need to be declared in the “Data Arrays” section, the FieldServer

virtual node(s) needs to be declared in the “Server Side Nodes” section, and the data to be provided

to the clients needs to be mapped in the “Server Side Map Descriptors” section. Details on how to

do this can be found below.

Note that in the tables, * indicates an optional parameter, with the bold legal value being the

default.

5.1 Data Arrays

Section Title

Data_Arrays

Column Title Function Legal Values

Data_Array_Name Provide name for Data Array Up to 15 alphanumeric

characters

Data_Format Provide data format. Each data array can only

take on one format. FLOAT, BIT, UInt16, SInt16,

Packed_Bit, Byte,

Packed_Byte, Swapped_Byte

Data_Array_Length Number of Data Objects. Must be larger than

the data storage area required for the data

being placed in this array.

1-10,000

Example

// Data Arrays

Data_Arrays

Data_Array_Name, Data_Format, Data_Array_Length

DA_AI_01, UInt16, 200

DA_AO_01, UInt16, 200

DA_DI_01, Bit, 200

DA_DO_01, Bit, 200

Altri manuali per Canatal Satchnet Driver FS-8700-59

Indice

Altri manuali FieldServer Hardware di rete

FieldServer

FieldServer ControlNet FS-8700-24 Nota di rilascio

FieldServer

FieldServer FS-8700-74 Nota di rilascio

FieldServer

FieldServer Telnet FS-8704-11 Nota di rilascio

FieldServer

FieldServer Modbus Plus FS-8700-02 Nota di rilascio

FieldServer

FieldServer FS-8700-22 X30 Nota di rilascio

FieldServer

FieldServer Hanning FS-8700-127 Nota di rilascio

FieldServer

FieldServer Genisys FS-8700-133 Nota di rilascio

FieldServer

FieldServer LonWorks FS-8700-21 Nota di rilascio

FieldServer

FieldServer Hanning FS-8700-127 Nota di rilascio

FieldServer

FieldServer Modbus Daniels FS-8700-15 Nota di rilascio

FieldServer

FieldServer Lutron Machine FS-8700-97 Nota di rilascio

FieldServer

FieldServer Gamewell FS-8700-83 Nota di rilascio

FieldServer

FieldServer A Sierra Monitor Company FS-8700-122 Nota di rilascio

FieldServer

FieldServer Gamewell FCI E3 Series Nota di rilascio

FieldServer

FieldServer Weigh-Tronix FS-8700-36 Nota di rilascio

FieldServer

FieldServer Profibus FS-8700-113 Nota di rilascio

FieldServer

FieldServer Dart FS-8700-78 Nota di rilascio

FieldServer

FieldServer ProtoCessor ProtoNode FPC-N34 Guida utente

FieldServer

FieldServer Honeywell Zellweger IR-148 FS-8700-102 Nota di rilascio

FieldServer

FieldServer FS-8700-114 X30 Nota di rilascio

FieldServer

FieldServer X-25 Guida utente

FieldServer

FieldServer Gamewell FCI 7100 Series Nota di rilascio

FieldServer

FieldServer Spectronics FS-8700-42 Nota di rilascio

FieldServer

FieldServer FS-8700-72 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente