Fimap IMx Manuale utente

GUIDE INCLUDES

 Setting up for use

 Using the machine

 Cleaning after use

 Care & maintenance

Instruction Manual for Fimap iMx

1. Choose your

Floor Pad

2. Unscrew the

Centre Cap

3. Attach the Floor

Pad

4. Tighten Centre

Cap

Red

Polished floors and

delicate areas

Blue

As red but slightly more

abrasive for heavier soiled

floors

Green

Heavy duty scrub for safety

flooring

Place the Drive Board on

the floor and unscrew the

centre cap

Remove the centre from

the floor pad and fit to

Drive Board, push to locate

with your thumbs.

Fit and tighten the centre

cap.

DO NOT OVER-TIGHTEN

Setting Up the Machine Before Use

5. Pull out the fill-

ing hose

6. Attach filling

hose to tap

7. Fill the tank 8. Add Chemical

Take machine to a tap

Start filling the tank with

cold water

Do not use hot water

Make sure the machine is

back on it’s rear wheels.

Watch the solution tube

and turn off tap when the

tank is full

Take out the chemical

filling container

(Next to the filling hose)

Add the chemical.

Add pour into the tank

Setting Up the Machine Before Use

Warning: Only use low foaming chemicals at the right dilution

9. Place Drive

Board on Floor

10.Place Machine

Over Drive Board

11. Switch the

Machine On

12. Engage Drive

Board

Place the drive board on

the floor in front of the

machine with the floor pad

face down as shown

Place the machine over the

drive board and push

handle up

Switch the machine on by

pressing the button above.

Ensure you use the I

setting at the top of the

switch.

Push the handle forward to

engage the drive board.

Squeeze and release the

start D handle three times

to engage

Setting Up the Machine Before Use

13. Switch on

vacuum

14. Lower the

Squeegee

15. Switch on

brush motor

16. Start Cleaning

Switch on the vacuum

switch

Lower the squeegee bar

onto the floor by pulling the

release lever on the back

of the machine out and

down

Squeeze the D handle to

start the brush motor

Start moving forward

Setting Up the Machine Before Use

Standard Cleaning Deep Cleaning

Part 1

Deep Cleaning

Part 2

For c

For deep cleaning, lift the

squeegee up, then switch

off the vacuum.

Scrub the floor allowing for

contact time for the

solution.

Then lower the squeegee,

switch the vacuum switch

on, switch off the solution

by switch the on switch to

the II setting.

Then move up and down to

pick up the solution.

Using the Machine

Move up and down in straight lines, overlapping

each pass

Always move forwards, do not go backwards with

the squeegee down.

1. Emptying Recovery Tank 2. Emptying the Solution

After every use, always empty the recovery

tank and rinse out with clean water

If you need to empty the solution tank, take the

machine to a suitable floor drain.

Unscrew the yellow tank bung in the side.

Allow the solution the drain out.

Clean the filter in the bung before refitting

Cleaning After Use

3. Remove and

clean Squeegee bar

4. Check hose 5. Clean bowl filter

cover

6. Check the floor

pad

Take the squeegee bar off

the machine by unscrewing

the two plastic nuts and

drawing the bar backwards

Disconnect the squeegee

hose.

Clean the squeegees

under running water

Refit squeegee bar

Check the squeegee hose.

If needed remove from

machine and flush through

with clean water.

Re-fit hose

Open the recovery tank

and remove the yellow

bowl filter cover and rinse

out.

Tip the machine back onto

the rear wheels.

With the machine switched

on, hold down the release

switch and then squeeze

the D handle once.

The Drive Board will

release

Cleaning After Use

1.Check the Battery

charge level

2. Charge Battery

When the batteries are

fully charged and the green

light is showing on the

charger, switch off the

charger and unplug from

the machine.

Re-plug in the machine

main cable connector

IMPORTANT!

ONCE THE BATTERY

HAS STARTED

CHARGING IT MUST

NEVER BE DISTRUPTED

UNTIL THE GREEN LIGHT

SHOWS ON THE

CHARGER

PERMENANT DAMAGE

TO THE BATTERY WILL

OCCUR IF CHARGING IS

DISRUPTED

Turn the machine on and

check the battery level

Try not to charge the

battery if the level is over

50%

To charge the battery

unplug in the main cable

here.

Fit the charger plug in it’s

place, switch on the

charger

Charging Battery and Storage

A+D Supplies

Marsh House

Brunel Road

Newton Abbot

TQ12 4PB

01626 355177

[email protected]

www.adswsupplies.com

Fimap IMx Manuale utente

Manuali Scrubber popolari di altre marche