FLASHFORGE 3D PRINTER Foto 8.9s Manuale utente
This guide is only applicable to Flashforge Foto 8.9s 3D printer
Foto 8.9s
Quick Start Guide
EN/CN-A03
Please put on gloves while using photopolymer resin to avoid
direct contact with hands.
To ensure the printing quality, please don’t open the light shield
unless it’s necessary.
Unused photopolymer resin needs to be stored in a dark, dry ,
and cool place.
Please clean the finished model with anhydrous alcohol.
Please ensure that the platform is installed correctly and no
items before operating to avoid damaging the LCD screen.
1.
2.
3.
4.
5.
WARNING
Each 3D printer has undergone a printing test before leaving the
factory. If there are residual consumables in the feed resin tank or
slight scratches on the printing platform, it is normal and will not
affect the use.
Dear customer:
Thank you for choosing and using the products of Flashforge Technology. Thank
you for your great support and help. The product quality and performance of
Flashforge Technology are excellent. For your convenience, please read the
manual carefully before use, and strictly follow the instructions of the manual.
The entire Flashforge Technology team is always ready to provide you with the
best quality service. No matter what problems you encounter during use, please
contact us according to the telephone and email provided at the end of the
manual.
In order for you to experience our products better, you can also obtain equipment
operating knowledge from the following channels:
01
Please unpack it carefully, you can take out the attached quick start guide from
the top layer of foam. The quick start guide will help you get familiar with the
device as quickly as possible and successfully complete the first printing
experience.
Note
Quick Starter Guide
Foreword
Safety tips: Please make sure to read the following safety
tips carefully
Work Environment Safety
Notice
Keep your work place tidy.
Do not operate in the presence of flammable liquids, gases or dust.
Children and untrained personnel should not operate the equipment alone.
Place Requirements
The device must be placed in a dry and
ventilated environment. The distances of the
left, right and back side space should be at
least 20cm, and the distance of the front side
space should be at least 35cm.
Environment Requirements
Temperature: RT 15-30℃
Moisture: 20%-70%
01
Electrical Requirements
Be sure to ground the device; do not modify the plug of the device. (Ungrounded/
incorrectly grounded/modified plugs will inevitably increase the risk of leakage)
Do not expose the device to humidity and hot sun. (Wet environment will increase
the risk of leakage/exposure will accelerate the aging of plastic parts)
Do not abuse the power cord, and be sure to use the power cord provided by Flashforge.
Do not use the device during thunderstorms. If you do not use the device for a long
time, please turn off the device and unplug the power cord.
Personal Safety
Please don’t direct touch the photopolymer resin with hands.
Please put on gloves and masks during operation.
Please don’t look at the light source directly.
Do not operate the device while you are tired or under the influence of drugs, alcohol
or medication.
Photopolymer Resin
Requirements
Please store the photosensitive
resin solution in a dark and dry
environment. Please place it in
a place out of the reach of
children. Please ensure that the
label surface of the bottle is
facing the eye-catching
direction.
Legal Notice
The user has no right to make any changes to this manual.
Flashforge Technology will not be responsible for any safety accidents caused by
customers disassembling or modifying the equipment by themselves. Without the
permission of Flashforge no one may modify or translate this manual. This manual is
protected by copyright, and Flashforge reserves the right of final interpretation of
this manual.
First edition (March 2021)
@Copyright 2020 Zhejiang Flashforge 3D Technology Co.,Ltd., Ltd. All rights reserved
Photopolymer Resin Storage
Unused photopolymer resin needs to be stored in a dark, dry, cool place, and out of
the reach of children. Ensure the bottle body logo faces in an eye-catching and visible
direction.
Cautions
Operate the device in a well-ventilated environment
Do not leave the device unattended for long
Do not make any modifications to the device
Do not operate the device in bright light.
Never use the device for illegal activities.
Never use the device to make any food storage vessels.
Never use the device to make any electrical appliance.
Never put the model into your mouth.
Do not remove the models with force.
02
Getting To Know Your 3D Printer
6. Resin Box
8. LCD
9. Ethernet
5. Build Plate
2. Platform Tighten Knob 3. Z-axis
11. Touched Screen
7. Box Tighten Knob
10. USB Stick Port
13. Power Slot
1. Light Shield
12. Power switch
4. Leveller
03
2
6
8
7
9
11
4
5
3
10
1
12 13
Accessory Box
After-sales card
Power Cable
USB Stick
3D Printer Quick Start GuidePower Adapter
Rubber Gloves
Resin Box
Wrench Set: Stamping wrench, Screw driver, Screws
Build Plate set：Build plate, Leveller, Handle
Resin Box Set：Resin Box, FEP Film, Film fixed frame,
Box Tighten Knob
Filter PaperWrench Set
Metal Scraper Plastic Scraper Build plate set
04
1. Connect the power adapter and power cable. Plug the output end of the
power adapter into the power input port on the back of the printer and turn
on the switch.
Leveling
Open the carton, take out the printer and accessories carefully, tear off the
winding film on the printer, and remove the tape and silicone strip for the
upper cover. Power up the printer.
2. Install the build plate on the plate holder. 3. Tighten the platform tighten knob.
05
6. Remove resin box. Put a piece of A4
paper folded in half on the 8.9’ LCD
screen.
7. Click [Tool] - [Manual] and open a new
window. Click [Home] and wait for stop
movement of Z-axis.
06
Print Tool System
4. To loose the screws on both sides of
the build plate by using an inner
hex wrench.
5. Make sure it can move free but
not to fall.
Move Residue WLAN
Stop
Stop
Z:
-
+
mm22 00
8. Press the top of the build plate with one hand to let four corners of build plate
to touch the LCD screen evenly. Pre-tighten the screws on both sides of the
platform and then lock them separately during the process. Twitch paper
and feel the resistance.
Notice: It must level for the first using. Suppose changing the new build plate
and new screen, and it has to level again. It needs to level when the
printing abnormal, such as the board on the side of the print model fell.
lock the screws
07
Press
First Printing
1. Make sure the LCD screen, build plate and
resin box is clear enough. Install the resin
box on the LCD screen.
3. After confirm the installation of resin box
and build plate, pour the resin into the
resin box. Note that capacity shall not
exceed the mark line in the resin box.
4. Close the light shield after all
above preparatory steps.
2. Tighten the knobs to fix the box.
08
09
5. Click the [Print] to enter the model list. Click the model file to star the printing.
Do not open the top cover during printing to avoid eyes hurt.
Note
Post-processing
1. There will be a prompt on the touch
screen when the printing is completed.
Click [OK] and then open the top cover.
2. Loose the nut to remove the build
plate.
Note: Be careful not to damage the
FEP film in the resin box or the LCD
screen during removal.
Print Tool System
Model-01
File list
Model-02
Model-03
Model-04
Model-01
1000
3 h 49 min
0.05 mm
Dental Model
1000
3 h 49 min
0.2mm
100%
OK
Print Completed!
Time: 3h49min
Indice
Altri manuali FLASHFORGE 3D PRINTER Stampante 3D
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Inventor II S Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Creator 3 Pro Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER inventor Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Creator Pro Guida utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Creator X Guida utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Adventurer 4 Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Guider IIS Series Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Adventurer 4 Series Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Guider2S Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Creator Pro Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER GUIDER 3 PLUS Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Adventurer 3 Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER finder Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Focus 8.9 Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER CREATOR PRO 2 Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Dreamer NX Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER inventor Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER EN-A01 Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER finder Manuale utente
FLASHFORGE 3D PRINTER
FLASHFORGE 3D PRINTER Hunter Manuale utente
