Fluke FlexCam Manuale utente

QuickStart: Flexcam

1© 2014 The Snell Group / 322 N. Main St. / Barre, VT 05641 / 800.636.9820 / www.thesnellgroup.com

1

1. MEMORY: The rubber cover, located on top of the

camera, is where the COMPACT FLASH card is

installed for data storage (required for saving).

2. POWER: Insert the BATTERY into the slot on the

bottom of the camera.

3. START: To turn the camera on, press the ON/OFF

switch, located on the left side of the camera,

adjacent to the LCD display.

The button should light up (green) and the start-up

screen for the Flexcam will appear.

4. AUTO ADJUST: Once the camera has completed

start-up, press the Auto-Adjust button.

This will automatically set the camera’s LEVEL and

SPAN.

5. FOCUS: Once adjusted, use the MANUAL FOCUS

(rotate lens) to bring the target into view.

Press the Auto-Adjust button once more to further

clarify the image.

6. PAUSE IMAGE: To capture an image, press the trigger button on the front of

the camera once. This will pause the image.

Hold the button down and it will capture the paused picture, saving it to disk.

.

Auto-Adjust

Camera Menu

Enter/Select

Battery Release

Joystick/Cursor

Power

Focus by turning lens

Compact Flash Port

AC Power &

USB/Firewire Data Ports

QuickStart: Flexcam

2© 2014 The Snell Group / 322 N. Main St. / Barre, VT 05641 / 800.636.9820 / www.thesnellgroup.com

2

7. MANUAL ADJUST (Span and Level): To manually adjust the image’s SPAN, use the

joystick to move the cursor over either the high or low number on the temperature scale.

For Flexcam S-Series cameras, these are arrows that appear as pairs at either end of the

scale).

Press enter.

A box should appear around the number

Use the joystick control to raise or lower the temperature until a desired SPAN is reached.

To manually adjust the image’s LEVEL, select the number in the center of the

temperature scale and repeat as indicated above.

This procedure can be done live or when an image is paused, on either the Flexcam or

Flexcam T-Series units.

It is only available in live mode on the S-Series.

8. PALETTE: To change the color palette for any camera, simply mouse-over the color bar

and, using the enter button, click through a series of pre-set palettes.

Indice

Altri manuali Fluke Attrezzature da laboratorio

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente