Fluke Ii900 Guida rapida

Altri manuali per ii900

3

Questo manuale è adatto per i seguenti modelli

1

Indice

Altri manuali Fluke Attrezzature da laboratorio

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente

Firmwa re Upgrade instr uctions for ii900 / ii910 Acoust ic Imagers –rev.1 –page 1

Internal

Upgrade instruction for Fluke ii900/ii910 units

Equipment

•A Windows-PC. The firmware file that will be provided needs to be copied to this PC.

•BP291 battery that comes with ii900 Series

•USB-C cable that comes with ii900 Series

Preparation for upgrading multiple units

•Use a BP291 battery that comes with the ii900 series battery (e.g. from one of the units) and

make sure it is charged to a level of 25%, or more.

•Use a USB-C cable (included with each ii900 Series) to connect Fluke ii900 series units to the USB

port of a PC

Upgrading units

•Open the packaging, take case out of the box and take unit out of the case.

•Open battery door, put battery in the unit, close battery door

•Power on the Fluke ii900/ii910. Note that it may take about 15…20 seconds before the unit

shows anything on screen.

•Connect the USB cable to the ii9x0 and to a USB-port of the PC

•On the PC, open Explorer and notice that a new device ‘FLK-ii900-Series’(or -ii910-) is now listed

in the list of drives and devices (see picture).

•Copy the new firmware file named (filename).SWU file from the PC

to the root folder (‘User Data’) of the Fluke ii9x0 Series imager.

•Once copied, the ii9x0 screen will show message, telling you that a

firmware update file is recognized, unit want to upgrade

•Tap ‘Yes’to confirm and start the firmware update. This may take a

few minutes (2 - 4 min. approx.)

•Once fully installed, a message will show on screen of the ii9x0,

telling you that the unit is about to restart

•Touch “OK” to activate the restart. The Fluke ii900 Series unit will

turn off and then on again. Like before, it may take over 15…20

seconds before the screen becomes active

•Verify that the new firmware has been loaded indeed: tap the screen, this will open a menu bar

at the left, tap Settings, tap ‘Imager Info’. This will open a screen showing Model, Serial Number,

and OS. This line should indicate the newly released firmware version (e.g: V4.6.168.x).

•Take off the grey cover that sits over the microphone array at the front of the imager

Firmwa re Upgrade instr uctions for ii900 / ii910 Acoust ic Imagers –rev.1 –page 2

Internal

•Check to see if the unit shows a

camera image as well as the sound

bar indicator, see image at the

right.

Sounds received from the

environment may result in colored

‘blobs’ on screen.

•If all is correct, turn off the unit by

pressing the ON/OFF key and

tapping ‘OK’

•Disconnect the USB-cable, place

back the mic array cover over the

mic array, take out the battery,

place back the battery cover and

lock it

•Place the battery pack and USB

cable back in the case if

appropriate. Please note: each ii900 and ii910 comes with 2 battery packs included,

either 2x Fluke BP291, or 2x RRC-2040-2, not mixed.

•Put instrument back in the case, put all accessories back in the carrying case and close the case

•Place case in the packaging, close the packaging

•If you’re handling multiple units: place a small tick-mark on the packaging box as a visual

indicator that this one has been through the upgrade, e.g. a dot on the box label using a marker

pen

Done!