Fluke 112 Manuale utente

FLUKE 112 / 115 TRUE RMS MULTIMETER Quick Start Guide

The Fluke 112 / 115 is a multimeter (volt-ohm-milliameter, or VOM, in some references) designed for

basic circuit measurements. Instrument settings are accessed via the main dial on the front. The

positions (which vary somewhat between the models) are (bold represents the ones we’ll use the most):

OFF: instrument off

Return the dial here when you are finished using the meter.

V~~: measures AC voltage (voltmeter)

V==: measures DC voltage (voltmeter)

mV: measures small DC voltages, with higher accuracy

Ω

: measures resistance (ohmmeter)

Note: the ohmmeter setting should never be used on an

energized circuit! It is only used to measure the resistance

of de-energized resistors. At best, measuring an

energized component will give incorrect values. At worst it

will blow a fuse inside the meter.

●))): continuity tester (audible ohmmeter).

This is useful for detecting short/open circuits; the system

beeps when low resistance is encountered, so you can check

many connections without looking at the display.

: Diode tester. (We will discuss this later.)

A~~: measures AC current (ammeter)

A==: measures DC current (ammeter)



)| : measures capacitors

This works similarly to the ohmmeter setting, and should only be used on a de-energized

component. Just as the ohmmeter measures resistance values, this gives capacitance values.

Hz: frequency meter – determines the frequency of an AC signal.

Other buttons:

HOLD: holds the current displayed value on screen. (Useful for copying values into your notes!)

RANGE: selects between auto-range and manual range selection

“Orange” button: used to select “orange” options on dial.

MIN MAX: display the minimum, maximum, or average values of the present measurement.

“sun” symbol: turns on display backlight

To use the meter, you connect two cords (one red and one black) to the bottom terminals as follows:

Black cord: always goes to the COM connector (center)

When measuring voltage, resistance, diodes, capacitors, resistance or frequency (everything but

current!), connect the red cord to the ”V Ω” (etc.) terminal at right. When the red cord is in this position

the meter should always be connected IN PARALLEL (i.e. across, not in line with) what you are trying to

measure, and the dial should never be on one of the “A” positions.

When measuring current (and current only!) connect the red cord to the “A” terminal at left. When the

meter is connected in this fashion, it should be connected IN SERIES (i.e. in line with) what you are trying

to measure, and the dial should be on one of the “A” positions.

There are four types of lead tips you can use, depending on preference:

“banana plugs” – tubular metal end, good for plugging into other devices

“probes” – pointy metal ends, good for poking around into circuits

“alligator clips” – grab on to what you want to measure (probably have very few of these)

“hook leads” – a springloaded hook that latches on to what you want. Better than alligator clips

in tight spaces.

The LCD display contains information about:

-what is being measured (volts, amps, ohms, farads, hertz; DC, AC),

-range settings being used (auto, or manual and the present range setting),

-display settings (Hold, Min, Max, Avg),

-instrument settings (e.g. low battery warning), and

-a bar graph along the bottom which gives a quicker (but less accurate) readout of measured values.

If you want to see every symbol displayed at once, press the “HOLD” button as you switch the meter on.

For further information, there are a number of manuals on the cart next to the meters.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Fluke Multimetro

Fluke

Fluke 87V Ex Manuale utente

Fluke

Fluke 8050A Manuale utente

Fluke

Fluke 80 Series III Manuale utente

Fluke

Fluke 21 Manuale utente

Fluke

Fluke 365 Manuale per l'uso e la cura

Fluke

Fluke ProcessMeter 787 Manuale utente

Fluke

Fluke a3002 FC Manuale per l'uso e la cura

Fluke

Fluke 8010A Manuale utente

Fluke

Fluke 175 Manuale per l'uso e la cura

Fluke

Fluke 8505A Manuale utente

Fluke

Fluke 91 Series II Manuale utente

Fluke

Fluke 15B Manuale per l'uso e la cura

Fluke

Fluke 106 Manuale utente

Fluke

Fluke 117 Manuale utente

Fluke

Fluke MD73AS3 Manuale utente

Fluke

Fluke 287 Manuale utente

Fluke

Fluke 8842A Manuale utente

Fluke

Fluke 8505A Manuale utente

Fluke

Fluke i410 Manuale utente

Fluke

Fluke 87 III Series Istruzioni per l'uso e l'installazione

Fluke

Fluke 87V/IMSK Manuale utente

Fluke

Fluke 2063513 Manuale utente

Fluke

Fluke 8840A Manuale utente

Fluke

Fluke 8840A Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente