Fluke 635 QuickBERT-T1 Guida alla configurazione
Manual Supplement
© 2001 Fluke Networks. All rights reserved. Printed in the U.S.A.
Manual Title: 635/633 Users Supplement Issue: 2
Part Number: 1278087 Issue Date: 12/01
Print Date: July 1999 Page Count: 14
Revision/Date: 1, 9/99
We’ve added two new features and
made several changes in Version 2.0
of the 635 QuickBERT-T1 tester. This
supplement provides an overview of
the tester’s new capabilities and
updates you on the changes and
corrections we’ve made in the latest
version.
This supplement contains information
necessary to ensure the accuracy and
completeness of the above manual. It
is organized as follows:
•New features
•Product Updates
•Corrections
635/633 Users Manual Supplement
12/01 1
New Features
Version 2.0 of the QuickBERT-T1 tester offers these two features:
•Prints current test results and setup information
•Downloads software updates
This section shows you how to use these new features.
Printing Current Test Results
The tester can print test results and setup information
automatically or on demand (when you press the PRINT key).
This section shows you how to set up the tester to enable
automatic printing or manual printing of test results.
Complete the following:
1. Using the supplied RS-232 cable, connect one end to the
tester and the other end to a printer.
2. Press the MODE this screen is displayed:
User Pattern
Done Setup
Contrast
abn22f.eps
3. Press the RESULTS key twice to display this screen:
Print
Done Setup
Date/Time
abn29f.eps
“Print” is blinking to indicate that it is selected.
Manual Supplement 635/633 Users
2 12/01
4. Press the SIGNALING TYPE (Setup) key.
The Setup Print screen is displayed. The current setting for
“Mode” is blinking:
Setup Print:
Done Tab
Mode: Norm Baud: 19.2
abn26f.eps
This screen lists the two setup parameters for printing:
“Mode” and “Baud”. “Mode” has two settings:
•Norm: (for manual printing) prints only when you press
the PRINT key.
•Auto: (for automatic printing) prints automatically when
the tester detects an error or alarm condition (bit error,
BPV error, Frame error or CRC error).
Note
If Auto is selected, you can also press the PRINT key to
print results.
“Baud” has four settings: 2.4, 4.8, 9.6, and 19.2.
5. To change the settings for "Mode" and "Baud", do the
following:
a) Press the RESULTS key to select the desired setting
for "Mode".
The setting blinks to indicate that it is selected.
b) Press the SIGNALING TYPE (Tab) key to move to
“Baud”. Then, press the RESULTS key until the
desired setting is displayed.
c) Press the MODE (Done) key to save your selections.
You return to the second page of the setup menu. “Print”
is blinking.
635/633 Users Manual Supplement
12/01 3
6. Press the MODE (Done) key to exit the setup menu.
You can print at any time by pressing the PRINT key. However, if
“Auto” is selected, the tester automatically prints a report when it detects
an error or an alarm.
Following is an example of the type of report that the tester prints:
Receive Status
Time: 07:54:06
Receive Setup:
Pattern : QRSS
Line Code : B8ZS
Frame : ESF
Input :TERM
Signal Present :Yes
Out of Frame:Yes
Blue Alarm :Yes
Ones Density :Yes
Excess Zeros :Yes
Yellow Alarm :Yes
Pattern Sync Loss :Yes
Dropped Channel : 2
DS0 Frequency : 0 . 0
DS0 Level : 0 . 0
DTMF Digits : None
Date: 01/21/01
Transmit Setup:
Pattern : QRSS
Line Code : B8ZS
Frame : D4
Clock : RX
Signal Present Hist : No
Out of Frame Hist : No
Blue Alarm Hist : No
Ones Density Hist : No
Excess Zeros Hist : No
Yellow Alarm Hist : No
Pattern Sync Loss Hist : No
Bit Errors : 0
BPV Errors : 0
Frame Errors : 0
CRC Errors : 0
Frequency Deviation : Yes
DS1 Frequency : 1544000
Clock Slips : -2
DS1 Level : 5.28vp-p
DS1 Level : -1.11dBD
E-Bit Sync : No
abn31f.eps
Manual Supplement 635/633 Users
4 12/01
Downloading Software Updates
When a software update becomes available for the tester, you can
download the latest version to a PC from the Fluke Networks web
site (http://www.flukenetworks.com). The web site provides
instructions for downloading and transferring the update software
from a PC to the tester. Using the web site requires Internet access
and a web browser.
Product Updates
Version 2.0 incorporates minor updates that we made to
enhance the usability of the product. These updates are
documented in this section. Page and section numbers are
given to help you locate the information to be updated in
the manual.
On page 1-6, replace the entire section 1-8 with the
following:
1-8. Adjusting the Contrast of the LCD
To adjust the contrast of the LCD, complete the following:
1. Press the MODE key until the following screen is displayed:
Note
The MODE key is the TEST MODE key on some models.
User Pattern
Done Setup
Contrast
abn22f.eps
2. Press the RESULTS key to select “Contrast”.
“Contrast” blinks to indicate that it is selected.
635/633 Users Manual Supplement
12/01 5
3. Press the SIGNALING TYPE (Setup) key.
The Setup Contrast menu is displayed:
Setup Contrast
Done
min max
:
abn28f.eps
The blinking rectangle on the min/max indicator shows the
current level of contrast.
4. Do one of the following:
•Press the RESULTS key to increase the contrast.
•Press the RESULTS key to decrease the contrast.
When the desired level of contrast is obtained, press the
MODE (Done) key.
You return to the first page of the setup menu. “Contrast” is
blinking.
5. To exit the setup menu, press the MODE (Done) key.
On page 1-2, section 1-2, add the following item to the list of
features:
•Prints test results and setup information
On page 1-4, section 1-6, add the following item to the first list:
•RS-232 cable
Manual Supplement 635/633 Users
6 12/01
On page 1-4, replace Figure 1-2 with the following figure:
A/C Power Adapter
ToolPack
Carrying Case
Users Manual
RS-232 cable
Bantam-to-
Bantam Cables
abn01f.eps
Figure 1-2. Supplied Equipment
On page 1-6, section 1-9, add the following sentence between the
first and second sentences:
Also available for purchase is a thermal printer.
On page 2-2, section 2-4, paragraph 3, change TEST MODE key
to MODE key, and add PRINT key to the list of keys.
635/633 Users Manual Supplement
12/01 7
On page 2-11, make the following changes:
Change:
2-16. TEST MODE Key
To:
2-16. MODE Key
Under section 2-16, replace the first sentence with the
following:
Pressing the MODE key allows you to select one of four modes:
T1, F64 (fractional T1, 64k), F56 (fractional T1, 56k) and Setup.
When you select Setup mode, you can access menus that enable
you to do the following:
•Change the contrast of the LCD
•Change the user pattern for a BERT test
•Set up the tester for printing test results
•Set the date and time
•Download new software to the tester.
On page 2-12, add the following prior to section 2-19:
2-18A. PRINT Key
This key enables you to print a summary report that includes
setup information and an analysis (both current and history) of
the signal present on the Rx receiver. For instructions on how to
set up the tester and how to print this report, see “Printing
Current Test Results” (earlier in this Supplement).
On page 2-14, add the following note prior to section 2-21:
Note
If the CSU loop code is selected and the QuickBERT-T1
receives a CSU Loop Up code for approximately five to ten
seconds, the tester enters TX THRU mode and displays
’CSU LOOPBACK’ on the third line of the display. After the
tester is in TX THRU mode, if it receives a CSU Loop
Down code, it responds by going back to the original TX
Pattern and clearing the third line of the display.
Manual Supplement 635/633 Users
8 12/01
On page 2-15, make the following changes:
Section 2-25, add the following to the end of the paragraph:
To arm the span, first select the ARM loop code. Then, press the
SEND LOOP UP key to arm the span. To disarm the span, press
the SEND LOOP DOWN key.
Section 2-26, add the following to the end of the paragraph:
To loop up the HTU-R, select the HTU-R loop code (with the
span armed) and press the SEND LOOP UP key. To loop down
the HTU-R, select the HTU-R loop code (with the span armed)
and press the SEND LOOP DOWN key.
Section 2-27, add the following to the end of the paragraph:
To loop up the HTU-C, select the HTU-C loop code (with the
span armed) and press the SEND LOOP UP key. To loop down
the HTU-C, select the HTU-C loop code (with the span armed)
and press the SEND LOOP DOWN key.
Section 2-28, add the following to the end of the paragraph:
To loop up the first doubler (if provided), select the HRE1 loop
code (with the span armed) and press the SEND LOOP UP key.
To loop down the first doubler, select the HRE1 loop code (with
the span armed) and press the SEND LOOP DOWN key.
Section 2-29, add the following to the end of the paragraph:
To loop up the second doubler (if provided), select the HRE2
loop code (with the span armed) and press the SEND LOOP UP
key. To loop down the second doubler, select the HRE2 loop
code (with the span armed) and press the SEND LOOP DOWN
key.
Section 2-30, add the following to the end of the paragraph:
To loop the HRU (remote interface) from the central office,
select the NREM loop code and press the SEND LOOP UP key.
To loop down the HRU, select the NREM loop code and press
the SEND LOOP DOWN key.
635/633 Users Manual Supplement
12/01 9
Section 2-31, add the following to the end of the paragraph:
To loop up the HLU (central office interface) from the central
office, select the NLOC loop code and press the SEND LOOP
UP key. To loop down the HLU, select the NLOC loop code and
press the SEND LOOP DOWN key.
Section 2-32, add the following to the end of the paragraph:
To loop up the first doubler (if provided) from the central office,
select the NDU1 loop code and press the SEND LOOP UP key.
To loop down the first doubler, select the NDU1 loop code and
press the SEND LOOP DOWN key.
Section 2-33, add the following to the end of the paragraph:
To loop up the second doubler (if provided) from the central
office, select the NDU2 loop code and press the SEND LOOP
UP key. To loop down the second doubler, select the NDU2 loop
code and press the SEND LOOP DOWN key.
On page 2-16, make the following changes:
Section 2-34, add the following to the end of the paragraph:
To loop up the HLU (central office interface) from the customer
side, select the CREM loop code and press the SEND LOOP UP
key. To loop down the HLU, select the CREM loop code and
press the SEND LOOP DOWN key.
Section 2-35, add the following to the end of the paragraph:
To loop up the HRU (customer interface) from the customer
side, select the CLOC loop code and press the SEND LOOP UP
key. To loop down the HRU, select the CLOC loop code and
press the SEND LOOP DOWN key.
Section 2-36, add the following to the end of the paragraph:
To loop up the first doubler (if provided) from the customer side,
select the CDU1 loop code and press the SEND LOOP UP key.
To loop down the first doubler, select the CDU1 loop code and
press the SEND LOOP DOWN key.
Indice
Altri manuali Fluke Apparecchiature di prova
Fluke
Fluke 7380 Manuale utente
Fluke
Fluke BT5300 Series Manuale utente
Fluke
Fluke TL2X4W-TWZ Manuale utente
Fluke
Fluke CableIQ Manuale utente
Fluke
Fluke 7526A Manuale per l'uso e la cura
Fluke
Fluke 1662 Manuale utente
Fluke
Fluke 725Ex Manuale utente
Fluke
Fluke 707 Manuale per l'uso e la cura
Fluke
Fluke 715 Manuale utente
Fluke
Fluke 9009 Manuale utente
Fluke
Fluke Versiv Series Manuale per l'uso e la cura
Fluke
Fluke 9102S Manuale utente
Fluke
Fluke 721 Manuale utente
Fluke
Fluke 5730A Manuale elenco delle parti
Fluke
Fluke 1503 Manuale utente
Fluke
Fluke 5520A Service Manuale utente
Fluke
Fluke NETWORK SERVICE MODULE DTX-NSM Manuale utente
Fluke
Fluke 6109A Manuale utente
Fluke
Fluke 718-100US Manuale utente
Fluke
Fluke 522A/6 Manuale utente
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Mercury
Mercury TSL01 Manuale utente
