Fluke DTX-CLT CertiFiber Manuale utente
PN 3565770 January 2010, Rev. 1 5/10
©2010 Fluke Corporation. All rights reserved. Printed in USA.
All product names are trademarks of their respective companies.
DTX-CLT CertiFiber®
Optical Loss Test Set
Getting Started Guide
The DTX-CLT CertiFiber Optical Loss Test Set is a rugged, hand-held
instrument used to certify, troubleshoot, and document fiber
cabling installations.
Accessing the Product Manuals
This guide provides basic information to help you get started using
the tester. For more detailed information, see the latest versions of
the DTX-CLT CertiFiber Users Manual and the DTX Series Technical
Reference Handbook provided on the DTX-CLT CertiFiber Product
Manuals CD and on the Fluke Networks website.
WWarningX
To avoid possible fire, electric shock, personal injury,
damage to equipment, or inaccurate test results, read the
safety information in the DTX-CLT CertiFiber Users
Manual before using the tester.
A
Power the Tester
•
You may power the tester with the ac adapter included or with
the removable lithium ion battery pack.
•
You may charge the battery when it is attached or detached
from the tester (Figure 1).
•
The battery charges fully in about 4 hours with the tester off. A
fully-charged battery lasts for at least 12 hours of typical use.
gfa01.eps
Figure 1. Charging the Battery (left) and
Removing the Battery (right)
B
Prepare to Save Tests
•
Check the memory space available:
Turn the rotary switch to SPECIAL FUNCTIONS; then select
Memory Status.
•
Select a cable ID source:
You can select IDs from a pre-generated list or create an ID after
each test. Turn the rotary switch to SETUP, select Instrument
Settings, select Cable ID Source; then select a source.
•
Set up a job folder:
On the Instrument Settings menu select Current Folder. Select
an existing folder or press JCreate Folder to create a new
folder.
•
Enter job information:
On the Instrument Settings menu press Cto show the tab with
the Operator, Site, and Company names. To enter a new name,
select a setting, press JCreate; then use the softkeys, BC
AD, and Hfor editing. Press Nwhen you are
finished.
C
Clean and Inspect All Connectors
WCaution
When using the fiber modules, use proper procedures to
clean and inspect all fiber connectors before every use.
Neglecting this step or using improper procedures can cause
unreliable test results and may permanently damage the
connectors. See the Users Manual for instructions.
D
Set the Reference
The reference serves as the baseline power level for loss
measurements.
Set the reference at these times:
•
At the beginning of each day using the remote end setup you
will use that day.
•
Anytime you reconnect a test reference cord to the module’s
output or other source.
•
Anytime the tester warns you that the reference is out of date.
•
Anytime you see a negative loss measurement. (See the
Technical Reference Handbook for more information.)
•
Anytime the tester tells you to set the reference.
To set the reference
1
Turn on the tester and smart remote and let them sit for 5
minutes. Allow additional time if the modules have been
stored above or below ambient temperature.
2
Turn the rotary switch to SETUP, then select Fiber Loss. Set the
following on the Fiber Loss tabs (press Cto see other tabs):
•
Test Limit: Select the test limit required for the job. Press
JMore to see other lists of limits.
•
Fiber Type: Select the fiber type to be tested.
•
Remote End Setup: Set to Smart Remote.
•
Bi-directional: Enable this if you are required to test the
fiber in both directions.
•
Number of Adapters and Number of Splices: Enter the
number of adapters and splices that will be added to each
direction of the fiber path after the reference is set.
•
Connector Type: Select the connector type used in the
cabling to be tested. Select General if the exact type is not
listed.
•
Test Method: Select 1 Jumper if you use the reference and
test connection shown in this manual.
3
Turn the rotary switch to SPECIAL FUNCTIONS, then select Set
Reference.
4
The Set Reference screen shows reference connections for the
test method you selected. Figure 2 shows Smart Remote mode.
Clean and inspect the connectors on the testers and test
reference cords, connect the tester and smart remote; then
press P.
gfa02.eps
Figure 2. Setting the Reference in Smart Remote Mode
(1 Jumper Method)
E
Make Sure Your Test Reference Cords are
Good
1
Disconnect the test reference cords from the INPUT ports on the
tester and smart remote.
2
Make the connections shown in Figure 3.
3
Turn the rotary switch to AUTOTEST, then press P.
4
Press Hto see the test results. The results for each fiber
(Input Fiber and Output Fiber) must be no more than these
limits:
WCaution
An overall result of PASS does not show that the test
reference cords are good. You must compare the loss to
the limits given here to make sure the cords are good.
Multimode test reference cord:
850 nm: 0.11 dB or less
1300 nm: 0.10 dB or less
(The limits are different because fiber has more loss at 850 nm
than at 1300 nm.)
Singlemode test reference cord:
0.20 dB or less for 1310 nm and 1550 nm
5
If a result is more than the limit shown above, use the procedure
given in the Users Manual to test the cords in the path that
failed (Input Fiber or Output Fiber). When you have good test
reference cords, set the reference and do these steps again
before you test a fiber link.
6
Save the test results to show that you used good test reference
cords to test the link.
Note
Fluke Networks recommends that you use this procedure
to make sure your test reference cords are good before
you test each fiber link.
gfa03.eps
Figure 3. Testing the Test Reference Cords in
Smart Remote Mode
F
Do a Test
1
Connect to the fiber you will test. Figure 4 shows Smart Remote
mode.
2
Turn the rotary switch to AUTOTEST, then press P.
gda04.eps
Figure 4. Testing a Fiber Link in Smart Remote Mode
(1 Jumper Method)
Registration
Registering your product with Fluke Networks gives you access to
valuable information on product updates, troubleshooting tips, and
other support services.
To register, fill out the online registration form on the Fluke
Networks website at www.flukenetworks.com/registration.
Contacting Fluke Networks
www.flukenetworks.com
support@flukenetworks.com
+1-425-446-4519
•
Australia: 61 (2) 8850-3333 or 61 (3) 9329-0244
•
Beijing: 86 (10) 6512-3435
•
Brazil: 11 3759 7600
•
Canada: 1-800-363-5853
•
Europe: +31-(0) 40 2675 600
•
Hong Kong: 852 2721-3228
•
Japan: 03-6714-3117
•
Korea: 82 2 539-6311
•
Singapore: 65 6799-5566
•
Taiwan: (886) 2-227-83199
•
USA: 1-800-283-5853
Visit our website for a complete list of phone numbers.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
Fluke Networks mainframe products will be free from defects in
material and workmanship for one year from the date of purchase.
Parts, accessories, product repairs and services are warranted for 90
days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries,
cables or other peripherals are all considered parts or accessories.
This warranty does not cover damage from accident, neglect, misuse,
alteration, contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other warranty
on Fluke Networks’ behalf. To obtain service during the warranty
period, contact your nearest Fluke Networks authorized service
center to obtain return authorization information, then send your
defective product to that Service Center with a description of the
problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE NETWORKS IS NOT LIABLE FOR ANY SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES,
ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
Fluke Networks
PO Box 777
Everett, WA 98206-0777
USA
4/04
Altri manuali per DTX-CLT CertiFiber
1
Indice
Altri manuali Fluke Apparecchiature di prova
Fluke
Fluke A40B Manuale utente
Fluke
Fluke T5-1000 Manuale tecnico
Fluke
Fluke P3800 Series Manuale utente
Fluke
Fluke 7060 Manuale utente
Fluke
Fluke 719 Series Manuale utente
Fluke
Fluke 5730A Manuale utente
Fluke
Fluke 80PK-10 Manuale utente
Fluke
Fluke 1507 Manuale utente
Fluke
Fluke T90 Manuale utente
Fluke
Fluke 725Ex Manuale utente
Fluke
Fluke 726 Manuale utente
Fluke
Fluke 712B Manuale per l'uso e la cura
Fluke
Fluke VoltAlert 2AC Manuale utente
Fluke
Fluke TS54-A-09-TDR Manuale utente
Fluke
Fluke 55XXA Manuale utente
Fluke
Fluke ProcessMeter 787 Manuale utente
Fluke
Fluke CertiFiber Manuale utente
Fluke
Fluke 4180 Manuale utente
Fluke
Fluke 718Ex 30G Manuale utente
Fluke
Fluke 190-062/AM Manuale operativo
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Mercury
Mercury TSL01 Manuale utente
