FOS Technologies WDMX TRX Manuale utente

FOS WDMX TRX

PRODUCT DESCRIPTION

The FOS WDMX TRX system is compact, lightweight and durable. Utilizing AFHSS - Adaptive Frequency

Hopping Spread Spectrum technology, the wireless system transmits or receives safe and reliable DMX

data without any delay and interference. Ideal for rental, mobile show, event, club, DJ, etc. Please read

this user manual carefully and thoroughly before operation.

Carefully unpack the carton, check the contents to ensure that all parts are present, and have been

received in good condition. Contact your supplier immediately and retain packing material for inspection

if any part is missing or damaged.

Safety Instructions

•This product is intended for indoor use only!

•Please keep this User Guide for future consultation.

•Do not attempt to dismantle and/or modify the transmitter in any way.

•To prevent risk of fire or shock, do not expose fixture to rain or moisture.

•Make sure that the voltage and frequency of power supply match the power requirements of the

transmitter/receiver.

•Make sure power cord is never crimped or damaged.

•The transmitter is only intended for installation, operation and maintenance by qualified

personnel.

Features

•Adaptive Frequency hopping technology - AFHSS

•Completely interference free

•Worldwide 2.45G ISM unLicense Frequency

•Transmit 512 channels (1 universe) of DMX data

•Maximum 16 universes of DMX in one area

•One-button-go for quick setup

•Plug and play, no need configuration for IP address

•Point-to-point, point-to-multipoint or multpioint-to-multipoint operation

Product Overview

Setup

Placing transmitter and receiver

For successful linking, the following conditions should be fulfilled:

•Distance between Transmitter & Receiver should not exceed 200 m.

•Position of Transmitter & Receiver should be at least above crowd and obstacles.

Use only DMX cables to connect DMX IN of the Transceiver to DMX source and DMX OUT of the Receiver

to lighting fixture.

The device is designed to operate with AC 100 / 230 Voltage. Please, before connecting it, make sure that

the power supply voltage matches the devices voltage.

Operation Instructions

Types of operation

One Transmitter supports one Universe (512 channels) and it can work with the Receivers in Point to Point

or Point to Multipoint network types.

Up to 16 DMX Universes can be transmitted simultaneously using multipoint to multipoint operation. All

receivers in a multipoint system will listen only to the designated transmitter without any delays or

interference from other systems working alongside.

Adding Receivers

1. Power on the Receiver unit(s) and ensure that they are not linked with any other transmitter (LINK

indicators should be OFF).

2. Press and quickly release FUNCTION button on the Transmitter. The transmitter will scan for all

unlinked receivers for a period of 10 seconds - the LINK indicator on both the Transmitter and

Receiver(s) will flash rapidly.

3. If successful, the LINK indicator on Receiver(s) now go ON. If any failed, check that the Receiver is

in range and repeat procedure.

You can add receivers at any time, even during operation. In an operational system, logging

on an additional receiver will make the logged-in units revert to idle mode for 10 seconds;

once the new units are logged-in they will all start again together with the new unit.

Unlink a Receiver

Press and hold the FUNCTION button on the Receiver for about 3 seconds till the LINK indicator go off.

Now the Receiver is unlinked.

Unlink all Receivers

On the Transmitter, press and hold the FUNCTION button until LINK begins flashing. All registered

Receivers linked to that Transmitter will be unlinked.

The Receiver will stay linked/logged on to the Transmitter no matter DMX signal or power is

cut off. The log-in information is stored in an EEPROM and will not be erased.

Setting a TRANSCEIVER to Transmit or Receive

The TRANSCEIVER can be used as a Transmitter or Receiver. To switch mode between Transmitter and

Receiver, power off the unit, then hold the FUNCTION button while power on the unit for 2 seconds. When

DMX and MODE indicators turn off, then the unit is a Receiver. Otherwise, it is a Transmitter.

Specifications

Transmission distance: 200m

IP rating: IP20

Power supply: AC 110V or 230V 50-60Hz

Dimension: 145mm x 100mm x 57mm

Weight: 1.40kg

FFC Notice

•This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference and (2), this device must accept any interference

received, including interference that may cause undesired operation.

•Changes or modifications not expressly approved by the manufacturer responsible for compliance

could avoid the user’s authority to operate the equipment.

Important Notice

To optimize the recovery and recycling of the materials that old appliances contain and reduce

the impact on human health and the environment, ensure that this product is recycled at the

end of its life.

Indice

Altri manuali FOS Technologies Trasmettitore

FOS Technologies

FOS Technologies AirLink Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente