Freescale Semiconductor EXtreme Switch Gen4 Manuale utente

Freescale Semiconductor, Inc.

User’s Guide

Document Number: KTXSWITCH4UG

Rev. 1.0, 11/2013

eXtreme Switch Gen4 Evaluation Board

Featuring the MC07XS6517 and MC17XS6500 Penta High Side Switch

Figure 1. eXtreme Switch Gen4 Evaluation Boards

Contents

1 Kit Contents/Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Jump Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3 Important Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5 Evaluation Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6 MC07XS6517 and MC17XS6500 Device Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

7 Accessory Interface Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

8 Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

9 Evaluation Board Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

10 Installing SPIGen Freeware on your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

11 Setting Up and Using the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

12 Evaluation Board Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

13 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

14 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

15 Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

16 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

17 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Kit Contents/Packing List

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

2Freescale Semiconductor, Inc.

1 Kit Contents/Packing List

• Assembled and tested evaluation board/module in anti-static bag.

• Warranty card

2JumpStart

•Gotowww.freescale.com/analogtools

•Locate your kit

• Review your Tool Summary Page

• Look for

• Download documents, software and other information

Jump Start Your Design

Important Notice

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

Freescale Semiconductor, Inc. 3

3 Important Notice

Freescale provides the enclosed product(s) under the following conditions:

This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES

ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs,

outputs, and supply terminals. This evaluation board may be used with any development system or other

source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This

evaluation board is not a Reference Design and is not intended to represent a final design recommendation

for any particular application. Final device in an application will be heavily dependent on proper printed circuit

board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O

signal quality.

The goods provided may not be complete in terms of required design, marketing, and or manufacturing related

protective considerations, including product safety measures typically found in the end product incorporating

the goods. Due to the open construction of the product, it is the user's responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the

customers applications, adequate design and operating safeguards must be provided by the customer to

minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical

support services.

Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from

the date of delivery and will be replaced by a new kit.

Freescale reserves the right to make changes without further notice to any products herein. Freescale makes

no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor

does Freescale assume any liability arising out of the application or use of any product or circuit, and

specifically disclaims any and all liability, including without limitation consequential or incidental damages.

“Typical” parameters can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typical”, must be validated for each customer application by customer’s

technical experts.

Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are

not designed, intended, or authorized for use as components in systems intended for surgical implant into the

body, or other applications intended to support or sustain life, or for any other application in which the failure

of the Freescale product could create a situation where personal injury or death may occur.

Should Buyer purchase or use Freescale products for any such unintended or unauthorized application, Buyer

shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors

harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,

directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized

use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the

part.Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or

service names are the property of their respective owners.

Introduction

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

4Freescale Semiconductor, Inc.

4 Introduction

This evaluation board demonstrates the capability of the latest eXtreme Switch Gen4 family. This family offers

new combinations of output channels as well as a selection of Rdson values. All devices are

footprint-compatible; therefore, they can all be evaluated using this evaluation board.

This evaluation board can be used to evaluate either the MC07XS6517 or the MC17XS6500 which are both

12 V penta high side devices that feature integrated control with high flexibility, and high number of protection

and diagnostic functions. These devices are designed for low-voltage automotive lighting applications and can

drive a wide range of sources, including HIB ballasts and LEDs.

Programming, control and diagnostics are accomplished using a 16-bit SPI interface, which makes possible a

large array of configurations, diagnostics and protection features. For example, see below:

• Configuration: Output slew rates, PWM frequency with prescaler, output phasing, current sense precision,

etc.

• Protection and diagnostics: under/overvoltage, thermal warning, overcurrent, open load, SPI fail, etc.

These devices also provide analog feedback of the IC's temperature, battery voltage or selectable-channel

current sensing with high precision.

The five channels can be controlled individually by external clock signal or in fail safe mode by using direct inputs

(available for OUT1 through OUT4). This fail-safe mode operation happens whenever communication with the

external microcontroller is lost (due to watchdog time-out) and all protection as well as control remains

operational.

5 Evaluation Board Features

This evaluation board consists of either an MC07XS6517 or MC17XS6500 IC in SOIC 54 or 32 pins with

exposed pads.

This board can control

• Five separate 28 W bulbs

• Three separate 55 W HID ballasts

• Five separate LED modules

• Five separate loads of other types

Device can be driven by the 16-bit SPI using KITUSBSPI with SPIGen software or with direct input signals in

Fail safe mode operation. It also offers the possibility to apply an external clock in order to drive outputs in PWM

operation.

6 MC07XS6517 and MC17XS6500 Device Features

MC07XS6517 and MC17XS6500 are smart + power ICs intended for lighting application. The devices supports

the following functions:

• Five protected high side switches

–3*7mOhms + 2*17 mOhms for the MC07XS6517

–5*17mOhms for the MC17XS6500

• Operating voltage range from 6.0 V to 18 V with sleep current < 5.0 µA.

• 16-bit 5.0 V SPI control, programming and status reporting with daisy chain capability

• PWM module using external clock with programmable slew rates (to satisfy EMC requirements), 8-bit

flexibility for duty cycle and output delay management.

• Smart overcurrent shutdown, severe short circuit detection, overtemperature protections, output short to

battery, undervoltage or overvoltage reporting, etc.

• Open load detection in On or Off state, available for bulbs and LEDs

• Analog temperature and voltage feedback, so current with selectable ratio is optimized for LEDs modules

Accessory Interface Board

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

Freescale Semiconductor, Inc. 5

Freescale analog ICs are manufactured using the SMARTMOS process, a combinational BiCMOS

manufacturing flow that integrates precision analog, power functions and dense CMOS logic together on a

single cost-effective die. All power channels are integrated using LFet45V technology.

7 Accessory Interface Board

The eXtreme Switch Gen4 Evaluation board may be used with the KITUSBSPIDGLEVME interface dongle

(shown below), which provides a USB-to-SPI interface. This small board makes use of the USB and SPI ports

built into Freescale’s MC68HC908JW32 microcontroller. The main function provided by this dongle is to allow

Freescale evaluation boards that have an SPI port to communicate with a PC through its USB port.

Figure 2. KITUSBSPIDGLEVME Interface Dongle

8 Required Equipment

Minimum equipment required:

• Minimum equipment required for optimal use:

• DC Power supply 30 V/40 A

• Clock signal generator 0-100 kHz

• Computer with an available USB port, running Windows XP or higher

• KITUSBSPIDGLEVME interface board

•Latest version of SPIGen software (available through www.freescale.com/analogtools)

• Typical loads (lamps)

Evaluation Board Configuration

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

6Freescale Semiconductor, Inc.

9 Evaluation Board Configuration

Figure 3. eXtreme Switch Gen4 Evaluation Board plus KITUSBSPIDGLEVME Board Setup

GND

+12 V

eXtreme Switch Gen4

Evaluation Board

USB/SPI Dongle

(KITUSBSPIDGLEVME)

16-Pin SPI Ribbon

Cable

Power Supply

Installing SPIGen Freeware on your Computer

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

Freescale Semiconductor, Inc. 7

10 Installing SPIGen Freeware on your Computer

The latest version of SPIGen is designed to run on any Windows 8, Windows 7, Vista or XP-based operating

system. To install the software, go to www.freescale.com/analogtools and select your kit. Click on that link to

open the corresponding Tool Summary Page. Look for “Jump Start Your Design”. Download to your computer

desktop the SPIGen software as well as the associated configuration file.

Run the install program from the desktop. The Installation Wizard will guide you through the rest of the process.

To use SPIGen, go to the Windows Start menu, then Programs, then SPIGen, and click on the SPIGen icon.

The SPIGen Graphic User Interface (GUI) will appear. Go to the file menu in the upper left hand corner of the

GUI, and select “Open”. In the file selection window that appears, set the “Files of type:” drop-down menu to

“SPIGen Files (*.spi)”. (As an exceptional case, the file name may have a .txt extension, in which case you

should set the menu to “All Files (*.*)”.) Next, browse for the configuration file you saved on your desktop earlier

and select it. Click “Open”, and SPIGen will create a specially configured SPI command generator for your

evaluation board.

The GUI is shown in Figure 4. The text at the top is the name of the configuration file loaded. The left side panel

displays folders that group user interfaces. The process of loading the configuration file has assigned a list of

“Extra Pins” as well as a list “Quick Commands”, all of which are board-specific.

Figure 4. SPIGen GUI

Setting Up and Using the Hardware

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

8Freescale Semiconductor, Inc.

11 Setting Up and Using the Hardware

In order to perform the demonstration examples, first set up the evaluation board hardware and software as

follows:

1. Ready the computer and install the latest available version of SPIGen GUI. Then connect the cable

between this interface board and computer. Finally, plug this interface board into the eXtreme Switch Gen4

Evaluation Board.

2. Attach a DC power supply (without turning on the power) to evaluation board’s Vpwr-Gnd connectors and

attach loads to the KIT07XS6517EVBE board. Plug the USB/SPI interface dongle (KITUSBSPIDGLEVME)

directly into the evaluation board.

3. Use as many output terminals as desired.

4. Launch SPIGen and load the GEN4_SPIgen_eval_rev1.spi configuration file obtained from the Jump Start

download.

5. Turn on the power supply with the correct voltage and verify that EVB is supplied correctly by observing the

D6 LEDs with JP1 and JP11 closed. J1 and J7 have to be set either to the Vcc or the µC position. Set all

the LED jumpers, JP2 to JP6, to outputs pins; set the "Extra Pin" RST_B (if J1 in uC position) to high on

the SPIGen GUI and then do the following verification:

6. Click on the "Extra Pins" button INx. The corresponding OUTx LED should turn on.

7. Click on the "Send Once" button. The 'SPI Word Received' at the top of the screen should answer

something different from 0x0000.

Once the steps above are all accomplished, then you are ready to proceed with the remaining examples.

11.1 SPIGen Software information

On the left side of the "device view", you have two options:

• "Single Command": The screen displays 16 bits from the SP interface, so the user can configure them easily

in binary or hexadecimal. You will also find at the top, the corresponding status of SI and SO bits and on

bottom left, the "SPI Word Session Log". Extra pins are also available for configuration.

• "Batch Commands" allows the user to create a specific function using commands that already exist.

Note:

• Some commands and batches of commands are already set up in the GEN4_SPIgen_eval_rev1.spi file.

You may create and save your own command for specific purposes.

• Gen4 devices need a WD toggle on bit D11 to stay in normal mode. The interface board

KITUSBSPIDGLEVME is not able to generate and take into account WD bit status. Therefore, when doing

your own sequence, you may take this into account, and use the "Send Continuously" button.

Evaluation Board Hardware Description

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

Freescale Semiconductor, Inc. 9

12 Evaluation Board Hardware Description

This evaluation board has the capability to demonstrate the functionality of either the MC07XS6517 or

17XS6500 IC, when either of those devices is mounted on the board as a Device Under Test. Below are shown

the DUT connections on the board. The labels displayed in red are accessible to a PC running SPIGen software.

Figure 5. Device Under Test Signals

12.1 LED Display

The following LEDs are provided as visual output devices for the KIT07XS6517EVBE evaluation board:

1. {LED Dx} indicates when the corresponding Outputx is On

2. {LED D6} indicates that Vcc is supplied by the on-board regulator

12.2 Test Point Definitions

Each test point of the board has a label showing its corresponding signal.

Device Under Test

Add SOIC32 pin 1 marking:

corresponds to pin3 of SOIC54

Capacitors layout placement:

- C22, C24, C20, C18, C16: near banana

- C23, C25, C21, C19, C17: near DUT pi

- C12, C13, C14, C15: near DUT

AGND

AGND AGND

AGND

OUT1

OUT2

OUT3

OUT4

OUT5

OUT6

CSNS

/SYNC

IN4

IN3

IN2

IN1

LIMP

CLK

MISO

MOSI

SCLK

CSB

RSTB

Vcc CP

Vcc

Vbat

C13

0.1UF

R265.0K

DUT

T07D17

IN1

IN2

IN3

IN4

CLK

LIMP

SCLK

MOSI

MISO

RST

GND_1

GND_2

VCC 8

CP 3

VBAT 55

OUT1_1 42

OUT1_2 43

OUT2_1 12

OUT2_2 13

OUT3_1 39

OUT3_2 40

OUT3_3 41

OUT4_1 14

OUT4_2 15

OUT4_3 16

OUT5_1 28

OUT5_2 29

OUT5_3 30

OUT5_4 31

OUT5_5 32

OUT5_6 33

OUT5_7 34

OUT5_8 35

OUT5_9 36

OUT5_10 37

OUT5_11 38

OUT6 10

CSNS 45

SYNC 46

NC_1

NC_2

NC_17

NC_18

NC_19

NC_20

NC_21

NC_22

NC_23

NC_24

NC_25

NC_26

NC_27

NC_53

NC_54

C20

0.022UF

JP8

C25

1000PF

C21

1000PF

C18

0.022UF

C14

0.1UF

C19

1000PF

C16

0.022UF

C15

1000PF

C17

1000PF

C22

0.022UF

R27

5.0K

C12

0.1UF

C24

0.022UF

C23

1000PF

Evaluation Board Hardware Description

KTXSWITCH4UG User’s Guide Rev. 1.0 11/2013

10 Freescale Semiconductor, Inc.

12.3 Input Signal Definitions

The MC07XS6517 and MC17XS6500 ICs both have special input signals that are used to control certain outputs

or functions inside the circuit. These signals are:

1. {INx} {Control of the corresponding OUTx}

2. {LIMP} {Force the IC into fail-safe mode operation when High}

3. {CLK} {To provide an external clock for PWM}

4. {RSTB} {Wakes up the device}

5. {VCC} {Allows SPI communication}

12.4 Output Signal Definitions

MC07XS6517 and MC17XS6500 ICs have six output signals that are used to connect loads (OUT1 to OUT5)

or an additional smart power device (OUT6).

12.5 Evaluation Board Connectors

Figure 6. Connector Designations

Output power connections

+12V

supply

KITUSBSPIDGLEVME Interface

Dongle

Spare

connector

for μC

Device I/Os

ext

sup

CLK

opt

Indice

Altri manuali Freescale Semiconductor Scheda madre

Freescale Semiconductor

Freescale Semiconductor M68EVB912C32 Manuale utente

Freescale Semiconductor

Freescale Semiconductor M52259DEMOKIT Manuale utente

Freescale Semiconductor

Freescale Semiconductor DEMO908GZ60 Manuale utente

Freescale Semiconductor

Freescale Semiconductor KIT33882EKEVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor PowerPC e500 Core Manuale utente

Freescale Semiconductor

Freescale Semiconductor KIT33908MBEVBE Manuale utente

Freescale Semiconductor

Freescale Semiconductor i.MX 6SoloLite Linux Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC5675EVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor MCIMX53SMD Manuale di installazione

Freescale Semiconductor

Freescale Semiconductor KIT22XS4200EKEVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor MSC8156 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC566EVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor MPC5748G EVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor FRDM-KL46Z Manuale utente

Freescale Semiconductor

Freescale Semiconductor MC13892 Manuale utente

Freescale Semiconductor

Freescale Semiconductor TWR-K70F120M Manuale utente

Freescale Semiconductor

Freescale Semiconductor TWR-MPC5125 Manuale utente

Freescale Semiconductor

Freescale Semiconductor NXP DEMO9S08JS16 Manuale utente

Freescale Semiconductor

Freescale Semiconductor MC13851 Manuale utente

Freescale Semiconductor

Freescale Semiconductor Babbage 2.5 Guida utente

Freescale Semiconductor

Freescale Semiconductor TWR-LS1021A Manuale utente

Freescale Semiconductor

Freescale Semiconductor BSC9131RDB Manuale utente

Freescale Semiconductor

Freescale Semiconductor M68HC12A4EVB Manuale utente

Freescale Semiconductor

Freescale Semiconductor 33395 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Freescale Semiconductor eXtreme Switch Gen4 Manuale utente

Manuali Scheda madre popolari di altre marche