Frigidaire FAS226R2A - Heavy Duty Room 22,000 BTU Air Conditioner... Manuale utente

Installation Instructions

For Heavy Duty (FAS Models) and

Median (FAM Models) Air Conditioners

Please read ALL instructions before installing.Two people are

recommended to install this product.If a new electrical outlet

is required,have the outlet installed by a qualified electrician

before installing unit. See#5 in Preliminary Instructions

following.

Preliminary instructions

Do the following before starting to install unit.See illustrations

below.

with this air conditioner are made to install in a wooden

Check dimensions of your unit to determine model type:

1. Check window opening size - the mounting parts furnished

sill double-hung window.The standard parts are for

window dimensions listed above.Open sash to a minimum

of 19"(483mm). (FIG. 1)

2. Check condition of window - all wood parts of window

must be in good shape and able to firmly hold the needed

screws.If not, make repairs before installing unit.

3. Check your storm windows - if your storm window

frame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG.2, or by removing

storm window while room air conditioner is being installed.

(continued)

Unit Height:

Unit Width:

Min. Window Opening:

Min. Window Width:

Max. Window Width:

Heavy duty (FAS) Median (FAM)

18.5/8" 17.5/8"

26 1/2"23 1/2"

18 1/2"

26 1/2"

40 1/2"

19"

31"

43"

FIG. 1 FIG. 2

SASH

19" MIN

1/2" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

SASH

1/2" MIN

19" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

1 1/2" MIN

BOARD THICKNESS AS

REQUIRED, ALONG

ENTIRE STOOL, FASTEN

WITH TWO NAILS OR

SCREWS.

SEAL-BOTTOM RAIL TO UNIT

SIDE RETAINER

FRAME

ASSEMBLY

(LEFT)

WASHER HEAD

LOCKING SCREW

FOAM GASKET

TOP ANGLE

FRAME

ASSEMBLY

(LEFT)

SAFETY LOCK AND

3/4" LONG HEX HEAD

SCREW

1/2" LONG

SCREWS AND

LOCKNUTS

LOCKNUT

3/4" LONG

FLAT HEAD

BOLT

WINDOW SUPPORT

BRACKET

WINDOW SASH SEAL

SILLANGLE

BRACKET

P/N 66121625

4. CHECK FOR ANYTHING THAT COULD BLOCK

AIRFLOW - check area outside of window for things

such as shrubs, trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not stop proper air flow.

5. Check the available electrical service - power supply must

be the same as that shown on the unit serial nameplate.

(See Owner's Guide for serial plate location.)Power cord

is 48"long. Be sure you have an outlet near.

All models have a 3-prong service plug to provide proper

service and safe positive grouding. Do not change plug in

any way. Do not use an adapter plug. If your present wall

outlet does not match your plug, call a qualified electrician

to make the needed change.

a large flat blade screwdriver

tape measure

adjustable wrench or pliers

pencil

Level

Socket wrenches

Phillips screwdriver

Tools Required

Hardware (in plastic bag)

6. Carefully unpack air conditioner - remove all packing

material. Protect floor or carpet from damage. Two

people should be used to move and install unit.

Avoid fire hazard or electric

shock. Do not use an extension cord or an

adaptorplug.Donotremoveany prong from

the power cord.

WARNING

Grounding type wall

receptacle

Do not, under any

circumustances, cut,

remove, or bypass the

grounding prong.

Power supply cord

with 3-prong grounding

plug and current

detection device

Washer Head

Locking Screw

For window panels

3/4" Long Hex-

Head Screw 3

Qty.

Safety Lock

1/2" Long Screw

and locknut

3/4" Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

4 ea.

2 ea.

Long hex-head

locking screw for

top angle, side

retainer 5/16"

Long

Remove Chassis Install Top Angle

and Side Bracket

Window Mounting

1. Pull down front panel and remove filter. (See FIG. 1).

2. Lift front upwards and place to one side. 1. Attach foam gasket to top angle above holes as

shown in FIG. 6.

3. Locate the four front screws and remove. These screws will

be needed to re-install the front later. (See FIG.2)

4. Pry away front from cabinet sides as per photo (see FIG.3)

5. Gently lift front off unit and place to one side (See FIG.4).

2. Install top

angle and

side retainers

to cabinet as

shown in FIG. 6.

FIG. 6

6. Remove shipping crews from top of unit and also on the side

by the base if installed.

7. Hold the cabinet while pulling on the base handle, and care-

fully remove the unit.

8. Add two foam inserts to holes in top of cabinet where

shipping screws were removed from.

Assemble Window

Filler Panels

1. Place cabinet on floor, a bench, or a table.

2. Slide "I" section of window filler panel into side retainer

on the side of the cabinet (see Figures 7-8). Do both

sides.

FIG. 7

PLASTIC

FRAME

WINDOW FILLER

PANEL

SIDE

RETAINER

FIG. 8

9. Your unit may come with internal packaging.THIS

PACKAGING MUST BE REMOVED PRIOR TO

INSTALLING THE AIR CONDITIONER BACK

INTO THE CABINET. (See FIG. 5)..AIR CONDITIONER

CABINET

TOP

VIEW

PLASTIC

FRAME

"I" SECTION WINDOW

FILLER

PANEL

LOCKING

SCREW

HOLE

FIG. 3 FIG. 4

FIG. 1

FIG. 5

Internal Packaging

FIG. 2

3. Insert top and bottom legs of window filler panel frame

into channel in the to angle and bottom rail. Do both

sides.

4. Insert washer head locking screws (2) into holes in

top leg of filler panel frame (see Step 6). Do not totally

tighten. Allow leg to slide freely. Screws will be

tightened after Section 6.

Install Support

5Bracket

1. Hold each support bracket flush against outside of sill,

and tight to bottom of cabinet as shown below. Mark

brackets at top level of sill, and remove.

Place Cabinet in

4Window

1. Open window and mark

center of window stool.

2. Place cabinet in window with bottom stool angle firmly

scated over window stool as shown. Bring window

down temporarily behind top angle to hold cabinet in

place.

STOOL

ANGLE

LEFT

LOCKNUT

SILL ANGLE

BRACKET

FLAT HEAD BOLT

2 EACH REQ'D FOR EACH

SUPPORT BRACKET

MARK

1/2" LONG SCREWS

AND LOCKNUTS

RIGHT

3. Shift cabinet left or right as needed to line up center of

cabinet on center line marked on stool.

4. Fasten cabinet to window stool with 2 screws into

holes.(You may wish to pre-drill pilot holes.)

5. Add bottom rail seal over screws to window stool.

2. Asscmble sill angle bracket to support brackets at the

marked position, as shown. Hand tighten, but allow

for any changes later.

3. Install support brackets (with sill angle brackets

attached) to correct hole in bottom of cabinet as shown.

4. Tighten all 6 bolts securely.

1/2" long screws

and locknuts

Bottom

Rail Seal

3/4" long HEX-

HEAD SCREW

Extend Window Filler

Panels

1. Carefully raise window to expose filler panel locking

1. Lift air conditioner and carefully slide into cabinet

3. Be sure chassis is firmly seated towards rear of cabinet.

4. Installation of front is the reverse of removal outlined

leaving 6" protruding.

in Section 1.

DO not push on controls OR finned coils.

screws. Loosen screws so filler panels slide easily.

2. Extend panels to fill window opening completely.

3. Close window behind top angle.

Tighten locking screws on top.

1. Trim sash seal to fit window width. Insert into space

between upper and lower sashes.

2. Attach right angle safety lock as shown.

LOCKING SCREWS

WINDOW SASH SEAL

SAFETY LOCK

3/4" long hex-

head screw

6Install Chassis into

Cabinet and Install

Front to Unit

Install Window Lock

and Sash Seal

Thru-The-Wall Installation

NOTE: Consult local building codes prior to installation,

This air conditioner has a slide-out chassis, so that it can be

installed through an outside wall as specified below:

Max wall thickness

Inside Frame Height:

Inside Frame Width:

18 " (47.9cm) 18" (45.7cm)

7/8

23 " (60.6cm)

7/8

26 " (67.9cm)

3/4

SIde louvers must never be blocked.

IMPORTANT:

All parts needed for Thru-The-Wall Installation are

provided,except a wood frame, shims, and 10 wood screws (#

construction at ends of windows, and under truss-bearing

points, etc.

can be installed,

10-1" long minimum). Select a wall surface that:

NOTE:

Heavy Duty (FAS) Median (FAM)

12" 10"

or a qualified carpenter.

1Select Wall Location

2Prepare Wall

1. does not support major structural loads such as the frame

stucco veneer). Working from inside the room, find wall

your model listed above.(Measure twice remember...)

Frame depth should be the same as wall thickness. Fill in

the space from the opening to the studs with wood spacers,

as shown.

dry wall.

stud nearest the center of area where air conditioner will

be installed (by sounding wall, or by magnetically finding

nails).

in FIG. 1.

FIG. 1

FIG. 2

1. Prepare wall in frame construction (including brick and

4. Build a wooden frame with the INSIDE dimensions of

5. Nail framd to spacers to spacers with front flush with

Carefully measure and cut an opening with the following

dimensions depending on your model. See FIGS. 1and 2.

of framing material used.

WIDTH "X" = inside model width plus twice the thickness

HEIGHT "Y" = inside model height plus twice the thickness

of framing material used.

2. Cut or knock out a hole on each side of center stud.

3. Measure between inside edges of every other stud as shown

2. does not have plumbing or wiring inside.

3. is near existing electrical outlets, or where another outlet

of installed air conditioner.

5. allows unblocked airflow from rear sides and end (outside)

4. faces, and is not blocked to the area to be cooled.

3-3/8" MIN

(8.6 cm)

NAIL SPACERS TO STUDS

LEVEL

Inside

Frame

Height Inside

Frame

Width

UP TO

8-1/2"

5. Screw or nail cabinet wooden frame using shims if

frame is oversized, to eliminate distortion. Remember

to maintain proper slope as described in Step 3.

6. Install chassis into cabinet by following all steps in

Step 8 of Window Mounting.(continued)

Support brakcet

Wooden strip

Refer to Step 4 of Window Mounting for assembly of

support brackets.A wooden strip nailed to the outside

wall should be used in conjunction with sill support

angle brackets.

FIG.2

1"LONG

WOOD SCREW

4. Secure bottom rail to wood frame with two large wood

screws 1"(2.5 cm)long using the two holes in the bottom

of the channel resting on frame.(See FIG.2 following)

FIG.1

3/4"PLUS

TRIM THICKNESS

5/16" SEE PARA 5

LEVEL

3/8"

2. Place cabinet into opening with bottom rail resting

firmly on bottom board of wooden frame.

3. Position cabinet to achieve proper slope for water removal.

(See FIG.1 below.)

1. Slide chassis from cabinet. Refer back to Step 1 of

Window Mounting.

NOTE: If wall thickness is 8-1/2" or more, add aluminum

flashing over bottom of frame opening to assure no water

can enter area between inner and outer wall.

CAULK AS

ALUMINUM FLASHING

OVER

REQUIRED

OVER BOTTOM OF FRAME

81/2"

Prepare and Install

3Cabinet

Masonry Construction

1. Cut or build a wall opening in the masonry wall similar

to the frame construction(refer to Step 2 of Thru-the-Wall

Installation for a wall thickness greater than 8-1/2").

2. Secure cabinet in place using masonry nails, or the right

masonry anchor screws.(Another way to do this is to build

an in -between frame of 2X4 's as shown in the Step 2 Prepare

Wall illustrations-but make it double framed on either side,

and install between masonry wall opening and cabinet.

Frame must be securely anchored to masonry wall opening)

Thiswaygivesverygoodlouverclearanceoneithersideofcabinet.

3. Install a linted to support masonry wall above cabinet.

Existing holes in cabinet can be used and/or additions holes

can be drilled to fasten cabinet at various positions.Be sure

that side louver clearance is in accordance with Step 1above.

4. Install exterior cabient suppport brackets as shown in

Step 2 of Thru-the-Wall Installation.Caulk or flash if

neede, to provide a wether-tight seal around top and sides

of cabinet.

5. To complete installation, apply wood trim molding

around room side projection of cabinet.

OPTIONAL: Caulking and installation of trim on interior

wall may be done. You can buy wood from your local lumber

or hardware supply. On the outside, caulk openings around top

and sides of cabinet, and all sides of wood sleeve to the opening.

NOTE: See Step 7, Item 3 of Window Mounting Instructions

for bottom rail seal location.

Altri manuali per FAS226R2A - Heavy Duty Room 22,000 BTU Air Conditioner...

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Frigidaire Condizionatore d'aria

Frigidaire

Frigidaire FAH10EJ2T2 Manuale utente

Frigidaire

Frigidaire FAH126R2T - 12,000-BTU Through-the-Wall Air... Manuale utente

Frigidaire

Frigidaire FAS254M2A1 Manuale utente

Frigidaire

Frigidaire FFTA1233Q25 Manuale del proprietario

Frigidaire

Frigidaire LRA257ST217 Manuale del proprietario

Frigidaire

Frigidaire FRA12EHT2 Istruzioni per l'installazione

Frigidaire

Frigidaire FAC066L7A1 Manuale utente

Frigidaire

Frigidaire FAC053J7A2 Manuale utente

Frigidaire

Frigidaire FAC064K7A2 Manuale utente

Frigidaire

Frigidaire FRA122BU1 Manuale utente

Frigidaire

Frigidaire FFRS0833Q1 Manuale utente

Frigidaire

Frigidaire FFMS121CQ10 Manuale utente

Frigidaire

Frigidaire CRA087AT715 Manuale utente

Frigidaire

Frigidaire FAP09C3AJW Manuale utente

Frigidaire

Frigidaire FAC085J7A2 Manuale utente

Frigidaire

Frigidaire CRA256ST211 Manuale del proprietario

Frigidaire

Frigidaire FAH08ET1T10 Manuale del proprietario

Frigidaire

Frigidaire CRA050XT73 Manuale utente

Frigidaire

Frigidaire FAX052P7A - Window Unit Air Conditioner Last One... Manuale utente

Frigidaire

Frigidaire LRA087AT73 Manuale del proprietario

Frigidaire

Frigidaire FRA103BT113 Manuale utente

Frigidaire

Frigidaire GALLERY GHPC132AB1 Manuale utente

Frigidaire

Frigidaire FAC053J7A4 Manuale utente

Frigidaire

Frigidaire FRA08PZU113 Manuale utente

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Samsung

Samsung AS09HM3N Manuale utente

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente

Webasto

Webasto Frigo Top 25 DS Manuale utente

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manuale utente