Frigidaire FRS093LS1 Manuale utente

8. The site must allow for the easy

removal of the connector pipe and

drain hose.

9. The unit must be installed at a site

protected from direct sunlight.

Precautions for Installation

Installation at the following sites may cause problems. If you must inevitably install

2. Sites with a high concentration of salinity, such as coastal areas.

3. Sites with sulfuric gas, such as hot water springs.

4. Sites with high frequency equipment, such as wireless equipment, welding

machines and medical installations.

5. Sites with flammable gases or volatile material.

6. Sites with special environmental conditions.

7. Laundry rooms.

Indoor Unit

1. The unit must be installed at a site

that does not obstruct the flow of

air.

2. The site must support the weight of

the indoor unit.

3. The site must be easily accessible

for maintenance and replacement

of the air filter.

4. The site must allow for the

necessary space around the indoor

figure.

that the unit be installed at the

flammable gases.

Choosing the installation site

the unit at one of these sites, please consult your local distributor beforehand:

1. Sites with machine oil.

unit, as shown in the sideward

meter) between the unit and radio

5. There should be at least 3 feet (1

7. The indoor unit must be at least 7.5

feet (2.3 meters) from the ground.

6. It must be far from fire, smoke or

center.

or television devices. It is ideal

than 6"

than 5"

than 7.5'

than 5"

Installation warnings:

Installation

1. Carefully read the installation manual before beginning.

2. Follow each step as shown.

3. Observe all local, state, and national electrical codes and by qualified,

licensed, authorized personnel only.

4. Pay attention to danger and safety notices

Outdoor Unit

1. The outdoor unit must be

installed at a convenient site

that is not exposed to strong

winds. The site should be dry

and well ventilated.

2. The site must support the weight

of the outdoor unit and allow

for vertical installation.

3. There must not be the possibility

of increased noise and vibration

at the site.

4. The unit must be installed at a

site where the noise produced

by its operation and air

discharge does not disturb the

neighbors or animals.

5. The site cannot have any

leakage of flammable gases.

space around the unit, as shown

access the installation site.

Choosing the installation site

in the figure.

6. The site must provide enough

7. Children must not be able to

than 1 feet

than 2 feet than 1 feet

than 2 feet

than 6.6 feet

Parts list

Indoor unit

Outdoor unit

Parts list

Installation plate

Clip anchor

Seal

Drain Joint

Remote controller

Remote Controller holder

Connecting

pipe

assembly

Liquid side

Gas side

NUMBER PART NAME QTY

(capacity < 12000 Btu's)

(capacity < 9000 Btu's)

(capacity > 12000 Btu's)

Ø3/8"

Ø1/4"

Ø1/2"

Ø3/8"

Ø5/8"

Self-tapping screw A #7X1"

Self-tapping screw B #7X3/4"

6Connecting cable

10 10

(capacity > 12000 Btu’s)

Attention

1. This illustration is for explanation purposes only.

Indoor unit

Outdoor

unit

Air filter

Parts list

2. Copper tubes must be insulated independently

More than 5"

More than 6"

More than 5"

More than 2 feet

than 2 feet

More than 6.6 feet

More than 1 feet

Attention

Fixing the Installation Plate

Drilling the Hole

1. Install the installation plate

horizontally over the structural

parts on the wall using the spaces

indicated on the plate, as shown

2. In the case of tiled, concrete or

diameter holes. Place anchorage

supports for the appropriate

assembly screws.

3. Fix the installation plate to the

1. Determine the position of the

installation plate and drill the

downward.

2. Always use a pipe cover with an

Installation plate

Fit the Installation Plate and drill holes

in the wall according to the wall

structure and corresponding mounting

points on the installation plate

(Dimensions are in “mm” unless

otherwise stated).

Wall

Indoor unit Outdoor unit

Indoor unit installation

(B)

Indoor unit outline Installation plate

the ceiling

from the wall from the wall

Refrigerant pipe Refrigerant pipe

Capacity

12000 Btu's

3.15

in the figures above.

A type screws.wall with eight

hole for the pipes using the

pipe hole so that it is tilted slightly

opening when drilling.

6" or more from

5" or more

hole (left) Ø 2.56" hole (right) Ø 2.56"

5" or more

3.55"

1.77"

0.72"

11.54"

19.27"

1.77"

36.25"

0.2"-0.28"

4. At all times securing to the wall

studs is recommended.

similar walls, create 0.2 inch

Connective pipe and drainage installation

Drainage

1. Run the drain hose sloping

downward. Do not install the drain

2. When connecting extension drain

hose, insulate the connecting part

of extension drain hose with a

shield pipe, do not let the drain

hose slack.

Connective pipe

1. For the left-hand and right-hand

piping, remove the pipe cover from

2. For the rear-right-hand and rear-left-

hand piping, install the piping as

connective pipe.

Indoor unit installation

1. Pass the piping through the hole in

the wall.

2. Put the upper claw at the back of

the indoor unit on the upper hook of

the installation plate, move the

indoor unit from side to side to see

that it is securely hooked.

Upper hook

Lower hook

Fastening the Indoor Unit

Do not put the end

of drain hose into water.

Do not block

water flow

by a rise.

Do not block

water flow

by a rise.

piping

Pipe cover

(left)

Pipe

holder

Pipe cover

(right)

Right piping

Connective

pipe

Indoor unit

outline

Rear right

piping

Rear left

Left piping

hose as illustrated sideward.

the side panel. The pipe cover

must be kept as it may

conditioner

to any other place.

be used

the air

shown in the sideward figure. Bend

the connective pipe to be laid at

the wall. Fix the end of the

when relocating

1.69"

a height of 1.69 inches or less from

Attention

Piping and wrapping

1. Bundle the tubing, connecting

cable, and drain hose with tape

2. Because the condensed water

from rear of the indoor unit is

gathered in ponding box and is

anything else in the box.

1. Connect the indoor unit first, then the outdoor unit.

2. Do not allow the piping to let out from the back of the indoor unit.

3. Be careful not to let the drain hose slack.

5. Be sure that the drain hose is located at the lowest side of the bundle. Locating

6. Never intercross nor intertwist the power wire with any other wiring.

7. Run the drain hose sloped downward to drain out the condensed water

smoothly.

Cushioning

material

3. Piping can easily be made by

lifting the indoor unit with a

cushioning material between the

indoor unit and the wall. Get it

out after finish piping.

4. Push the lower part of the indoor

unit up on the wall, Then move

the indoor unit from side to side,

up and down to check if it is

hooked securely.

Indoor unit installation

Indoor unit

Cable

Ponding

box

Pipe room

Wrapping

belt

Drain hose

Connective

pipe

securely and evenly as shown

in the sideward figure.

piped out of room, do not put

connection

at the upper side may cause drain pan to overflow inside the unit.

4. Both of the auxiliary piping should be heat insulation.

1. Install the outdoor part of the unit

on a rigid surface to avoid excess

noise and vibration.

2. Direct the air vent toward an area

without obstacles.

especially in areas where it is

frequently windy.

4. If the installation site is exposed to

heavy winds, such as in coastal

areas, place the unit along the

widest part of the wall or use

protective plates.

requirement in the installation

bracket diagram. The installation

wall should be solid brick, concrete

or the same intensity construction,

supporting should be taken.

The connection between bracket

and wall, bracket and the air

conditioner should be firm,

stable and reliable.

6. Be sure there is no obstacle which

Outdoor unit installation

Strong wind

Outdoor unit installation

3. Install the unit at the site where it is

exposed to as little wind as possible,

or action to reinforce, damping

schrubs or bushes.

blocks radiating air, including

5. If suspended installation is needed,

local or servicer. The installation

purchase kit No.EA140S from your

bracket should accord with technique

Settlement of outdoor unit

Anchor the outdoor unit tightly and

horizontally on a concrete or rigid

Fit the seal into the drain elbow, then

insert the drain joint into the base

pan hole of outdoor unit, rotate 90

securely assemble them. Connect

the drain joint with an extension

drain hose (Locally purchased), in

case of the water draining off the

outdoor unit during the heating

Air inlet

Air

inlet

Air outlet

Outdoor unit installation

Base pan hole

of outdoor unit

Seal Drain joint

Seal

Drain pipe

Drain joint installation

mode or rainy season.

A (inch) B (inch)

Outdoor unit dimension inch(WxHxD)

2.25'x1.41'x0.85'

2.56'x1.77'x0.82'

2.49'x1.94'x0.94'

2.77'x2.28'x1.10'

1.51'

1.80'

1.74'

1.84'

0.82'

0.91'

0.95'

1.10'

2.30'x1.76'x0.77'

1.50'

separately).

or 0.32 inch diameter (Purchasedy

mount with a bolt and nut 0.39 inch

Altri manuali per FRS093LS1

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Frigidaire Condizionatore d'aria

Frigidaire

Frigidaire FAC054K7A1 Manuale utente

Frigidaire

Frigidaire FRA102BT1 Manuale utente

Frigidaire

Frigidaire FFRE0533Q1 Manuale utente

Frigidaire

Frigidaire FAA086P7A - 8,000 BTU Mini Compact Room Air... Manuale utente

Frigidaire

Frigidaire FAC126N1A Manuale utente

Frigidaire

Frigidaire FAS254J2A1 Manuale utente

Frigidaire

Frigidaire CRA084KT710 Manuale utente

Frigidaire

Frigidaire FAS183K2A1 Manuale utente

Frigidaire

Frigidaire FAK103J1V1 Manuale utente

Frigidaire

Frigidaire FRA08PZU110 Manuale del proprietario

Frigidaire

Frigidaire FAH08ET1T10 Manuale del proprietario

Frigidaire

Frigidaire FRA053PU113 Manuale del proprietario

Frigidaire

Frigidaire FAC084J7A2 Manuale utente

Frigidaire

Frigidaire FRA113PT110 Manuale utente

Frigidaire

Frigidaire FFHP093WS2 Manuale utente

Frigidaire

Frigidaire FGRQ0633U1 Manuale del proprietario

Frigidaire

Frigidaire FRP12ETT2A Manuale utente

Frigidaire

Frigidaire FAX054P7A6 Manuale utente

Frigidaire

Frigidaire FAS25EQ2A2 Guida rapida

Frigidaire

Frigidaire FAS185M2A2 Manuale utente

Frigidaire

Frigidaire FFRE1233S1 Manuale del proprietario

Frigidaire

Frigidaire Home ComfortFRA086HT1 Manuale utente

Frigidaire

Frigidaire FRA08EZT71 Manuale utente

Frigidaire

Frigidaire FAH10EP2T Manuale utente

Manuali Condizionatore d'aria popolari di altre marche

Spheros

Spheros CC 355 Manuale utente

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuale utente

Panasonic

Panasonic CS-E12HKEW Manuale utente

nedis

nedis ACMB1WT7 Manuale utente

Samsung

Samsung AR KV Series Guida

Daikin

Daikin FCFV50A Manuale utente

Fujitsu

Fujitsu Inverter ASBA30JFC Manuale utente

Toshiba

Toshiba RAS-M10SMUV-E Manuale utente

Daikin

Daikin FXLQ20MAVE Manuale utente

Hitachi

Hitachi RAS-E24CAK Manuale utente

CIAT

CIAT Magister 2 Series Guida

Bestron

Bestron AAC6000 Manuale utente

Hisense

Hisense 7K Manuale tecnico

Samsung

Samsung AS09HM3N Manuale utente

Soleus Air

Soleus Air GB-PAC-08E4 Manuale utente

McQuay

McQuay MCK020A Manuale utente

Webasto

Webasto Frigo Top 25 DS Manuale utente

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Manuale utente