Front Runner FATF006 Manuale utente
ENG
220 min
toyota 4 Runner (2009 - CURRENT)
Foot Rail
FATF006_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
1
IMPORTANT WARNING!
Don’t be a hero and muscle through this without first reading these fitting instructions! Improper installation of this gear may void certain aspects of
your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
FATF006
READ ME FIRST
START HERE!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
FATF006_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
2
IN THE BOX
FIGURE 1.1
1 2 X Front Foot Rail; 1xLH, 1xRH
2 2 X Rear Foot Rail; 1xLH, 1xRH
3 24 X Nut Cap M8
4 12 X Hex Bolt M8x40
5 12 X Spring Washer M8
6 24 X Flat Washer M8x16x1.6ss
7 12 X Hex Bolt M8x20
8 12 X Nyloc Nut M8
9 4 X Rivnut M8
10 6 X Spacer
11 8 X Button Head M6x16
12 2 X Joiner Plate
13 8 X Flat Washer M6x12x1ss
14 8 X Nyloc Nut M6
15 8 X Nut Cap M6
IN THE BOX TOOLS NEEDED
10mm
13mm
IN THE BOX
1GET ORGANIZED
Here is what you are looking at for FATF006
4mm
3
4
5
6
7
6
8
11
1
2
13
12
14
15
10
10
3
9
4mm
7mm Rivnut Setter
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
3
FATF006_REV_A00
FIT AND SECURE
2
13mm
2.1
2.2
2.3
Drill the pilot holes to 11.5mm and
secure two rivnuts (item 9) in the holes
by using a rivnut setter.
With the factory rails removed, use the
center of the existing front hole of the
roof rail, mark out the dimension as
shown on the ditch molding. Do this on
the left and right side.
Place the assembled foot rail over the
existing holes and markings to check.
5mm
11.5mm
520
570
Place the spacer (item 10) over the
marks you have made. Mark the
outsides of the spacer.
Drill 5mm pilot holes though the ditch
molding and the vehicles roof to mark.
Make sure not to drill to deap otherwise
you will damage the inside lining of the
roof.
Now cut the ditch molding on the marks
you have made so that the spacer can fit
in the ditch.
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
4
FATF006_REV_A00
4
13
12
14
15
11
4
6
10
9
5
FIT AND SECURE
13mm
13mm
Place a bead of sealant in and over each
hole in the roof, then place a spacer
(item 10) over each hole.
Place the foot rail that you assembled in
step 2.4 on the spacers and loosely fit it
with the fasteners shown.
Assemble the front and rear foot rail
(items 1 and 2) with the joiner plate
(item 12) with the fasteners shown.
10mm
4mm
2.4
2.5
FIT AND SECURE
3
2.2
2.4
2.1
3.2
3.3
4MM
3.1
Refer to RRSTUNI when assembling your Slimline II Tray.
Make sure that the wind diflector is
installed before you proceed to the next
step.
3.4
Centre the rack and fully tighten all the fasteners. Use M8 nut caps (Items 3) to finish off the nuts.
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
5
FATF006_REV_A00
4
Slide item 7 into the t-slots shown in
step 3.3. Loosely fit the roof rack to the
foot rails by using items 6,7 and 8.
7
6
8
3
13mm
13mm
© COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
5
FATF006_REV_A00
4
COMPLETION
4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or online.
9
4.1
Congratulations. You did it. Take a step back and admire your work!
Indice
Altri manuali Front Runner Accessori per automobili
Front Runner
Front Runner SLIMLINE II Manuale utente
Front Runner
Front Runner SSDR012 Manuale utente
Front Runner
Front Runner Pro Water Tank with Strap Manuale utente
Front Runner
Front Runner Pro Bike Carrier Manuale utente
Front Runner
Front Runner RRAC210 Manuale utente
Front Runner
Front Runner RRAC248 Manuale utente
Front Runner
Front Runner PBTT002 Manuale utente
Front Runner
Front Runner LAVT003 Manuale utente
Front Runner
Front Runner TRAC003 Manuale utente
Front Runner
Front Runner SSDS105 Manuale utente
Front Runner
Front Runner GBHO012 Manuale utente
Front Runner
Front Runner QE Series Manuale utente
Front Runner
Front Runner PRO UNDER RACK TABLE bracket Manuale utente
Front Runner
Front Runner SLIMLINE II TRAY Manuale utente
Front Runner
Front Runner RTTENT101 Manuale utente
Front Runner
Front Runner TRCA008 Manuale utente
Front Runner
Front Runner RRAC203 Manuale utente
Front Runner
Front Runner LALD004 Manuale utente
Front Runner
Front Runner GOFR001 Manuale utente
Front Runner
Front Runner SLIMLINE II Manuale utente
