FS Fiberstore S8050-20Q4C Manuale utente
S8050-20Q4C
V2.1
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide
S8050-20Q4C
2 4
1 3 123 4 567 8 910 11 1 2 13 10 1 5 16 17 18 1 9 20 21 2 2 23 24
1
40GEBreakout
40G/100G
2 3 4
L3 FULLY MANAGED PLUS SPINE SWITCH
L3 FULLY MANAGED PLUS SPINE-SWITCH
SWITCH SPINE L3+ ENTIÈREMENT GÉRÉ
Introduction
Accessories
Thank you for choosing S8050-20Q4C spine switch. This guide is designed to familiarize you with the
layout of the switch and describes how to deploy the switch in your network.
S8050-20Q4C
Power Cord x 2
Grounding Cable x 1
Mounting Bracket x 2
Rubber Pad x 4 M4 Screw x 8
Console Cable x 1 CatSe Cable x 1
S8050-20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 10 11 12 13 10 15 16 17 18 19 20 21 22 23 24
1
40GEBreakout
40G/100G 234
1
EN
Front Panel Ports
Front Panel LEDs
Hardware Overview
ETH
Console SFP+ QSFP+ QSFP28 QSFP+
S8050-20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 10 11 12 13 10 15 16 17 18 19 20 21 22 2 3 24
1
40GE Breakout
40G/100G 2 3 4
S8050-20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 10 11 12 13 10 15 16 17 18 19 20 21 22 2 3 24
1
40GE Breakout
40G/100G 2 3 4
USB
SFP+ SFP+ ports for 1 0G connection
QSFP+ ports for 40G connection
QSFP28 ports for 1 00G connection
An Ethernet management port
An RJ45 console port for serial management
QSFP+
QSFP28
ETH
Console
USB
SYS SFP+ QSFP+ QSFP28 QSFP+
40/100G Breakout LED
FAN
ID PWR
ETH
Ports Description
2
EN
LEDS
SYS
FAN
Status Description
PWR
ETH
SFP+
QSFP+
QSFP28
Green
Blinking Green Quickly (2Hz)
Blinking Green Slowly (0.5Hz)
Amber
Blinking Amber Quickly (2Hz)
Blinking Amber Slowly (0.5Hz)
System is abnormal.
System is running in u-boot mode.
System is normally running.
System occurs alarm or error.
System is initial in u-boot mode.
System software is in initial state.
No power or no system runs or runs abnormally.
Green
Amber
Green
Amber
FAN module is normally running.
FAN module occurs error.
Power supply is absent.
Power supply is OK.
Power supply is abnormal.
Power supply is absent or single power supply is
abnormal.
Green
Blinking Green
Green
Blinking Green
Green
Blinking Green
Green
Blinking Green
Port is linked.
Port is receiving or transmitting packets.
Port is not linked.
10G port is linked.
10G packets are receiving or transmitting.
Port is not linked.
40G port is linked.
40G packets are receiving or transmitting.
Port is not linked.
100G port is linked.
100G packets are receiving or transmitting.
Port is not linked.
3
EN
Back Panel
Installation Requirements
switch.
Before you begin the installation, make sure that you have the following:
Site Environment:
Do not operate it in an area that exceeds an ambient temperature of45 °C .
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1Uheight available.
Category 5e orhigherRJ-45 Ethernet cables forconnecting the network devices.
The installation site must be free from leaking or dripping water, heavydew, and humidity.
Ensure rack and working platforms are well earthed.
Be sure that the switch is leveland stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
2 Hot-swappable Power Supplies
4 Hot-swappable Fans
Grounding Point
S8050-20Q4C
24
1 3 1 2 345 6
4
EN
Mounting the Switch
Desk Mounting
1. Attach fourrubber pads to the bottom.
2. Place the chassis on a desk.
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with eight M4screws.
S8050-20Q4C
24
131 2 3 4 56789 10 1112131015 16171819 20 21 2 2 23 24
1
40GEBreakout
40G/100G
2 3 4
S8050-20Q4C
2 4
1 3 1 2 3 4 5 6 7
7 8 9 10 11 1 2 13 10 15 16 17 1 8 19 2 0 21 2 2 2 3 24
1
40GE Breakout
40G/100G
2 3 4
5
EN
2. Attachthe switchto the rack using fourM6 screws and cage nuts.
Grounding the Switch
1. Connect one end of the grounding cable to aproper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug tothe grounding point on the switch back panel withthe washers and
screws.
CAUTION: The earth connection must not be removed unless all supplyconnections have
been disconnected.
89 10 11 1 2 13 1 0 15 1 6 1 7 18 1 9 20 21 2 2 2 3 24
1
40GE Breakout
40G/100G
234
6
EN
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical modules
Connecting the Power
1. Plug theACpower cord intothepower port on the back of the switch.
2. Connect the other end of the power cord to anAC power source.
WARNING: Do not install power cable while the power is on.
Connecting the SFP+ Ports
connect DAC cables to theSFP+ slots.
S80 5 0 - 20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 10 11 1 2 13 1 0 15 1 6 17
40G/100G
7
EN
Connecting the QSFP+ Ports
connect DAC cables to theQSFP+ slots.
Connecting the QSFP28 Ports
connect DAC cables to theQSFP28 slots.
18 19 202 1 22 2 3 24
1
40GE Breakout
234
S8 0 50-20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 1 0 1 1 12 13 1 0 15 1 6 17 1 8 1 9 20 21 22 23 24
1
40GE Breakout
40G/100G
2 3
S8050-20Q4C
2 4
1 3 1 2 3 4 5 6 7 8 9 1 0 1 1 12 13 1 0 15 16 17 18 19 2 0 2 1 22 2 3 24
1
40GE Breakout
40G/100G
2 3
8
EN
Connecting the Console Port
S8050-20Q4C
2 4
1 3 1 2 3 4 567 8
1. Insert the RJ45 connector of the console cable into the RJ45 console port onthe front of theswitch.
2. Connect the other end of the console cable tothe RS-232 serial port on the computer.
Connecting the USB Port
3 4
3 4
S8050-20Q4C
2 4
1 3 1 2 345 6 7 8 9 10 11 1 2 13 10 15 16 17 18 19 2 0 2 1 22 2
40GE Brea
40G/100G
USB
9
EN
Altri manuali per Fiberstore S8050-20Q4C
1
Indice
Lingue:
Altri manuali FS Interruttore
FS
FS S3260-8T2FP Manuale utente
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS S1150-8T2F Manuale utente
FS
FS MANAGED L2 Manuale utente
FS
FS PoE+ Series Manuale utente
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS S3910 Series Manuale utente
FS
FS PoE+ Series Manuale utente
FS
FS S3200 Series Manuale utente
FS
FS S5500-48T6SP-R Manuale utente
FS
FS N Series Manuale utente
FS
FS S3700-24T4F Manuale utente
FS
FS S3150-8T2FP Manuale utente
FS
FS S3410 Series Manuale operativo
FS
FS S5300-12S Manuale utente
FS
FS IES3100-8TF-P Manuale utente
FS
FS S5860 Series Manuale operativo
FS
FS KVM-160217IP Manuale utente
FS
FS S5860-20SQ Manuale utente
