FS S3400-48T6SP Manuale utente
V1.0
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide
S3400-48T6SP
ETHERNET L2+ POE+ SWITCH
ETHERNET L2+ POE+ SWITCH
SWITCH ETHERNET L2+ POE+
S3400-48T6SP POE+
Introduction
Thank you for choosing the S3400-48T6SP Ethernet L2+ PoE+ Switch. This guide is designed to
familiarize you with the layout of the switch and describes how to deploy it in your network.
S3400-48T6SP
Accessories
Console Cable x1 Grounding Cable x1
M3 Screw x8
Power Cord x1
Mounting Bracket x2
EN
1
Rubber Pad x4
S3400-48T6SP POE+
Ethernet Cable x1 M6 Screw & Nut x4
Front Panel LEDs
Hardware Overview
Front Panel Ports
Ports Description
RJ45
CONSOLE
SFP+
10/100/1000BASE-T ports for Ethernet connection
An RJ45 console port for serial management
SFP+ ports for 10G connection
EN
2
PWR
SYS
The switch is powered on.On
On
Off
Off
Blinking
The switch is not powered on or the indicator is faulty.
The system is being started up.
The system works well.
The switch is not working or the indicator is faulty.
RJ45
On
Off
On
Off
The link on the port is normal.
The link on the port has failed.
The link on the port is normal.
The link on the port has failed.
LEDs State Description
SFP+
On
Off
Connected PD device, working properly.
PoE
The indicator status of the Ethernet port is Link, not PoE power supply.
S3400-48T6SP POE+
RJ45 SFP+
CONSOLE
S3400-48T6SP POE+
RJ45
SFP+ PWR
SYS PoE
Front Panel Button
Back Panel
Installation Requirements
Screwdriver, static-proof wristband, and other Ethernet terminal devices.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ45 Ethernet cables and fiber optical cables for connecting network
devices.
Before the installation, make sure that you have the following:
Site Environment:
Make sure that the temperature of the installation site is maintained at 0°C~45°C.
The installation site must be well-ventilated. Ensure that there is adequate airflow around the
switch.
The switch should be installed at least 1U (44.45mm) away from devices to its sides.
Button Description
SWAP Swap function, used to switch PoE indication.
EN
3
S3400-48T6SP POE+
SWAP
ON
POWER
Input:100-240Vac
Freq:50/60Hz
OFF
Power Supply (DC) Grounding Point Power Supply (AC)
Power ON/OFF
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure the rack and working platforms are well-earthed.
Mounting the switch
Desk Mounting
1. Attach the four rubber pads to the four corners on the switch bottom.
2. Place the switch on the smooth and safe desk.
EN
4
NOTE: Do not put things weighing 4.5 kg or over 4.5 kg on the top of the switch.
S3400-48T6SP POE+
S3400-48T6SP POE+
S3400-48T6SP POE+
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with the supplied screws.
2. Attach the switch to the rack using the screws.
EN
5
NOTE: When you fix the brackets, the front panel of the switch faces forward.
Grounding the Switch
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers and
screws.
Connecting the RJ45 Ports
S3400-48T6SP POE+
EN
6
ON
POWER
Input:100-240Vac
Freq:50/60Hz
OFF
S3400-48T6SP POE+
S3400-48T6SP POE+
1. Connect an Ethernet cable to the RJ45 port of a network device.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
1. Plug the compatible SFP+ transceiver into the SFP+ port.
2. Connect a fiber optic cable to the fiber transceiver. Then connect the other end of the cable to
another fiber device.
Connecting the SFP+ Ports
Connecting the Console Port
EN
7
1. Insert the RJ45 connector into the RJ45 console port on the front panel of the switch.
2. Connect the DB9 female connector of the console cable to the serial port on the computer.
Connecting the Power
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Configuring the Switch
Configuring the Switch Using the Console Port
Step 1: Connect a computer to the console port of the switch with the console cable.
Step 2: Start the terminal simulation software, such as HyperTerminal on the computer.
Step 3: Set the parameters of the HyperTerminal: Baud rate to 115200, Data bits to 8, Parity to None,
and Stop bits to 1.
WARNING: Do not install power cables while the power is on.
EN
8
ON
POWER
Input:100-240Vac
Freq:50/60Hz
OFF
Configuring the Switch Using the Web-Based Interface
Step 1: Connect a computer to the Ethernet port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x ("x" is any number from 2 to 254).
x
Quick Connect
Protocol:
The port may be manually entered or selected from the list.
Serial
Flow Control
DTR/DSR
RTS/CTS
XON/XOFF
Save sessionShow quick connect on startup
Open in a tab
Connect Cancel
COM3
115200
8
None
1
Port:
Baud rate:
Data bits:
Parity:
Stop bits:
Name of pipe:
Step 4: After setting the parameters, click Connect to enter.
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses:
EN
9
Indice
Lingue:
Altri manuali FS Interruttore
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS S3150-8T2FP Manuale utente
FS
FS KVM-160217IP Manuale utente
FS
FS S5860-20SQ Manuale utente
FS
FS PoE+ Series Manuale utente
FS
FS S3900 Series Manuale utente
FS
FS S5500-48T8SP Istruzioni operative
FS
FS PoE+ Series Istruzioni operative
FS
FS N Series Manuale utente
FS
FS S1150-8T2F Manuale utente
FS
FS S58 Series Manuale utente
FS
FS S5860-24XB-U Manuale utente
FS
FS S1900-24T Manuale utente
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS S3700-24T4F Manuale di istruzioni
FS
FS PoE+ Series Manuale utente
FS
FS S5860 Series Manuale utente
FS
FS N Series Manuale utente
FS
FS S3910 Series Manuale utente
FS
FS S3150-8T2FP Manuale utente
