Fujitsu FI-6130 Guida alla configurazione
fi-6130 / fi-6230 Cleaning and Maintenance
TROUBLESHOOTING
CONTENTS MAP
TOP
All Rights Reserved. Copyright 2007 © PFU LIMITED
Cleaning and Maintenance
fi-6130 / fi-6230
fi-6130 / fi-6230 Image Scanner Operator's Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
Chapter 4 DAILY CARE
This chapter describes how to clean the scanner.
CAUTION
When operating the scanner, the ADF's glass becomes very hot.
Before you clean inside the scanner, turn off its power and unplug the AC adapter from the
outlet. Wait for at least 15 minutes for the ADF glass to cool down.
Do not turn off the scanner when you clean the Feed and Eject rollers.
WARNING
Do not use any aerosol sprays or alcohol based sprays to clean the scanner.
Dust blown up by strong air from the spray may enter the inside of the scanner. This may
cause the scanner to fail or malfunction.
Sparks, caused by static electricity, generated when blowing off dust and dirt from the
outside of the scanner may cause a fire.
All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operator's Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
4.1 Cleaning Materials and Locations Requiring Cleaning
Cleaning Materials
The table below shows the cleaning materials that are used on this scanner.
Cleaning Materials Part No. Remarks
Cleaner F1 PA03950-0352 1 bottle (100 ml)
Moisten cloth with this fluid and wipe the scanner
clean. (*1)
Cleaning wipe PA03950-0419 24 sheets per pack (*1)(*2)
Soft, dry cloth Commercially available.
*1: For details on Cleaner F1, consult the agent where you bought your scanner or an authorized FUJITSU service provider.
*2: Pre-moistened with Cleaner F1, Cleaning Wipes are used instead of moistened cloths.
HINT
It may take long before the cleaner vaporizes if a large quantity is used. When cleaning the
scanner parts, dampen a cloth with modest quantities of the cleaner. In addition, wipe off
the cleaner completely with a soft lint-free cloth to leave no residue on the surface of the
cleaned parts.
Locations and Cycle for Cleaning
Location Standard Cleaning Cycle
Brake roller Clean every 5,000 scanned sheets.
Pick roller
Feed roller
Plastic roller
Eject roller
Glass
Ultrasonic sensor
ATTENTION
The scanner must be cleaned more frequently when the following documents are used:
mDocuments of coated paper
mDocuments with printed text or graphics almost covering the entire surface
mChemically treated documents such as carbonless paper
mDocuments containing a large amount of calcium carbonate
mDocuments written by pencil
mDocuments on which the toner is not fused sufficiently
Detergent for cleaning windows or glass cleaner can be used instead of Cleaner F1. However,
do not use paint thinner or other organic solvents.
All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operator's Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
4.2 Cleaning the Flatbed [fi-6230 only]
1. Open the document cover.
2. Clean the following locations using a soft cloth moistened with Cleaner F1.
Plastic cover
Document bed
ATTENTION
Do not allow moisture to get inside the device during cleaning.
3. Wait for cleaned parts to dry.
4. Gently close the document cover.
All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operator's Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
4.3 Cleaning the ADF
As a Guideline, clean the ADF every 5,000 scanned sheets. Note that this guideline varies according to the type of documents
you scan. For example, it may be necessary to clean the ADF more frequently if documents are scanned when the toner is not
sufficiently fixed on the printout.
CAUTION
The glass surface of the ADF becomes hot during the operation of the scanner.
Before you start to clean the inner parts of the scanner, disconnect the AC adapter from the
power outlet, and wait at least 15 minutes to let the glass cool down.
1. Open the ADF by pushing on the ADF open lever and turning the ADF to the front.
ADF open lever
CAUTION
Be careful, the ADF may close and pinch your finger.
2. Clean the following locations with a soft, dry cloth moistened with Cleaner F1.
No. Item
1 Brake rollers (x 2)
2 Feed rollers (x 2)
3 Eject rollers (x 2)
4 Glasses (x 2)
5 Pick rollers (x 2)
6 Plastic rollers (x 4)
7 Ultrasonic sensors (x 2)
ATTENTION
To avoid damaging the document sensors, take care that the cloth does not get hooked into
them when cleaning the inside of the ADF.
Document sensor
Brake roller
Lightly clean the Brake roller along the grooves on the roller taking care not to scratch the roller surface.
When cleaning the Brake roller, remove it from the scanner. For how to remove the Brake Roller, see Section "5.3
Replacing the Brake Rollers."
Pick roller
Lightly clean the Pick roller along the grooves on the roller taking care not to scratch the roller surface. Take particular
care in cleaning this roller as black debris on it adversely affects the pickup performance.
Plastic roller
Lightly clean the Plastic roller taking care not to damage the roller surface. Take particular care when cleaning this
roller as black debris on it affects document pick performance. Be careful not to damage the sponges attached around
the middle of the roller.
Glass
Clean lightly.
HINT
If the glass is dirty, vertical streaks may apper in the scanned images.
Ultrasonic sensor
Clean lightly with a dry cloth.
With the movie below, review the procedure to clean the Brake roller, Pick roller, Plastic roller, and ADF glass surfaces:
Feed roller/Eject roller
1) Open the ADF when the indication of the Function Number display is not "P" or "0".
If you open the ADF when the indication of the Function Number display is "P" or "0", the Feed rollers/Eject rollers
will not rotate even you perform the operation of step 2 below.
2) Simultaneously hold down the [Send to] and [Scan] buttons on the Operator Panel.
The Feed rollers/Eject rollers start to rotate slowly.
3) Hold a soft cloth moistened with cleaning fluid against the surface of the rotating Feed rollers so that it lightly
cleans the surface of the rollers. Take particular care when cleaning these rollers as black debris on these rollers
affects pickup performance. As a guideline, seven presses of the [Send to] and [Scan] buttons make the Feed
rollers/Eject rollers to rotate one full turn.
[Send to] Button
[Scan] Button
CAUTION
In step 2, all the Feed rollers/Eject rollers turn at the same time. When cleaning the Feed
rollers or Eject rollers, be careful not to touch the other rotating Feed rollers/Eject rollers.
With the movie below, review the procedure to clean the Feed rollers/Eject rollers:
3. Press down on the center of the ADF to return it to its original position until the ADF button locks.
Press center of ADF.
ATTENTION
When the ADF has returned to its original position, make sure that it is completely closed.
Feeding errors may occur if the ADF is not closed completely.
All Rights Reserved. Copyright 2007 © PFU LIMITED
fi-6130 / fi-6230 Image Scanner Operator's Guide
TROUBLESHOOTING
CONTENTS MAP
TOP
Chapter 5 REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows XP.
Also, when the FUJITSU TWAIN32 or FUJITSU ISIS scanner driver is updated the screens and operations noted in this chapter will
differ slightly.
Refer to the manuals provided with the update.
WARNING
When operating the scanner, the ADF's inside glass becomes very hot.
Before you replace the consumables, turn off its power and unplug the AC adapter from the
outlet. Wait for at least 15 minutes.
All Rights Reserved. Copyright 2007 © PFU LIMITED
Altri manuali per FI-6130
5
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Fujitsu Stampante
Fujitsu
Fujitsu FTP-621CDL003 Manuale utente
Fujitsu
Fujitsu FI-590PRF Operators Manuale
Fujitsu
Fujitsu DL7600Pro Manuale utente
Fujitsu
Fujitsu fi-7480 Manuale utente
Fujitsu
Fujitsu FTP-628WSL Manuale utente
Fujitsu
Fujitsu PrintPartner 16V Manuale utente
Fujitsu
Fujitsu DL900 Manuale utente
Fujitsu
Fujitsu FTP-638MCL101 Manuale utente
Fujitsu
Fujitsu SP-1120 Manuale
Fujitsu
Fujitsu FTP-639MCL054 Manuale utente
Fujitsu
Fujitsu N7100 Manuale
Fujitsu
Fujitsu ULTIMA90 Manuale utente
Fujitsu
Fujitsu DL3600 Manuale utente
Fujitsu
Fujitsu fi-4530C Guida alla configurazione
Fujitsu
Fujitsu 10 ppm Manuale utente
Fujitsu
Fujitsu DotMax 24 series Manuale utente
Fujitsu
Fujitsu FTP-628MCL101 Manuale utente
Fujitsu
Fujitsu DL1100 Manuale utente
Fujitsu
Fujitsu M304X series Manuale di installazione e funzionamento
Fujitsu
Fujitsu FTP-631MCL201 Manuale utente
