FUTABA FX-30 Istruzioni operative

Altri manuali FUTABA Trasmettitore

FUTABA

FUTABA FP-6EX - ADDENDUM Manuale utente

FUTABA

FUTABA R3006SB Manuale utente

FUTABA

FUTABA T14SG Istruzioni per il montaggio

FUTABA

FUTABA T14SG Manuale tecnico

FUTABA

FUTABA 9z Manuale utente

FUTABA

FUTABA FX-18 Manuale utente

FUTABA

FUTABA 9CAP SUPER Manuale utente

FUTABA

FUTABA T6EXA Manuale utente

FUTABA

FUTABA T7PXR Manuale tecnico

FUTABA

FUTABA R3006SB Manuale utente

FUTABA

FUTABA R7008SB Manuale utente

FUTABA

FUTABA 3PRKA Manuale utente

FUTABA

FUTABA T16IZ Manuale utente

FUTABA

FUTABA R3008SB Manuale utente

FUTABA

FUTABA FMT-02 Manuale utente

FUTABA

FUTABA FX-3/FMT-01 Manuale tecnico

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente

Duplex TU module fits this transmitter well but it is necessary to mount it inside the

transmitter. Antenna can be placed to the original place. Transmitter must be switched off

during manipulating. It is necessary to solder. Put transmitter on a soft pad to avoid

damage.

Switch transmitter off

Turn upside down

pen rear casing

Futaba FX-30

Futaba FX-30

Unscrew the antenna

Remove rubber stopper.

Unscrew 5 screws

Remove plastic covering

Unscrew original antenna. Choose right position for new antenna and remove rubber

stopper in the top of the transmitter. Unsrew five screws that holds black plastic covering

and remove it.

Unscrew 3 screws

Disconnect connectors on

the perimeter of the

mainboard

Cut one connector

Unscrew 3 screws that holds mainboard. Remove connectors that are on the perimeter of

the mainboard carefully so that the mainboard can be turned upside down. Duplex TU

module package contains connecting cable. Cut conector at one side of the cable.

Futaba FX-30

Stick double-sided tape

Modify the antenna

connector

Stick double-sided tape on the Duplex TU module. It is necessary to modify the antenna

connector as shown on a picture. Be careful not to overheat the connector during grinding.

Hitec Eclipse 7

Futaba FX-30

Put antenna connector

through out from the

transmitter

Put on plastic part

Screw the nut

Unscrew the nut and washer from the connector, put the connector through out from the

tansmitter. Put antenna connector through prepared hole out from the transmitter, put

washer and screw from outside and screw it.

Futaba FX-30

Solder the cable to the

board

Screw 2.4 GHz antenna

Solder prepared connecting cable to the board of the transmitter properly as show on a

picture. Be sure that soldered connections are not too high because there is not enough

free space between board and plastic covering.

Futaba FX-30

Put the board back to the

transmitter

Screw the board with 3

screws

Put on black covering and

screw it

Put the mainboard back to the transmitter carefully and screw it with 3 screws. Adjust the

cables that go under the board so that they don't cross each other. Connect all the

connectors back to the board. Be sure that the board is not deflected. Put on black plastic

covering and screw it with 5 screws.

Futaba FX-30

Stick Duplex TU module to

the transmitter

Connect batteries

Remove paper covering from the double-sided sticky tape and stick Duplex TU module to

the right place as shown on a picture. Connect cable that goes from the transmitter to the

Duplex TU module to IN connector (Input). Insert batteries and connect it to the transmitter.

Futaba FX-30

Mount rear casing

Screw 2.4 GHz antenna

Incase the transmitter with reverse procedure see page 1. Screw enclosed antenna.

Installation is completed. Before using it is necessary to pair off new receiver and

transmitter, see receiver manual.