Futech SPINNER RED Manuale utente

USER

MANUAL

062.03R SPINNER RED

062.03G SPINNER GREEN

EN ENGLISH

Manual

in your language?

Check the back cover

02 05

B O

OVERVIEW

HOUSING

01 Laser head

02 Plumb point up (Z-axis)

03 Keypad

04 X-axis

05 Y-axis

06 Quick guide

07 Power socket

08 5/8” screw Horizontal mode

/ Plumb point down (Z-axis)

09 5/8” screw Vertical mode

10 Wallmount

(horizontal mode) /

Foot (vertical mode)

(removable)

11 Battery compartment

12 Model label

13 Serial number

14 Remote control

15 Window cover

KEYPAD

A Power button

B Arrow UP button

C Arrow DOWN button

D Arrow LEFT button

E Arrow RIGHT button

F Speed button

G Scan button

H Slope button

I Tilt button

J Turn LEFT button

K Turn RIGHT button

L LED Slope indicator

M LED Tilt indicator

N LED Power indicator

O Infrared eye

REMOTE CONTROL

b Arrow UP button

c Arrow DOWN button

d Arrow LEFT button

e Arrow RIGHT button

f Speed button

g Scan button

h Slope button

j Turn LEFT button

k Turn RIGHT button

QUICK START GUIDE

KEYPAD

REMOTE

CONTROL

NAME

FUNCTION

A - Power button Press short Switch ON/OFF the device

B b Arrow UP button Press short or Hold Change the slope.

Y-axis rises on the side pointed by the arrow of the y-axis.

C c Arrow DOWN button Press short or Hold Change the slope.

Y-axis descends on the side pointed by the arrow of the y-axis.

D d Arrow LEFT button (Horizontal mode)

Press short or Hold

Change the slope.

X-axis rises on the side pointed by the arrow of the x-axis.

(Vertical mode)

Press short or Hold

Move the laser line and dot (z-axis) to the left

E e Arrow RIGHT button (Horizontal mode)

Press short or Hold

Change the slope.

X-axis descends on the side pointed by the arrow of the x-axis.

(Vertical mode)

Press short or Hold

Move the laser line and dot (z-axis) to the right

F f Speed button Press short Change spinning speed

0 – 120 – 300 – 600 RPM

G g Scan button Press short Use and change scan modus

0° - 10° - 45° - 90° - 180°

H h Slope button Press short Switch ON slope modus. (Automatic levelling is switched off)

I - Tilt button Press short Switch ON/OFF Tilt security

J j Turn LEFT button Press short or Hold Turn the laser anti clockwise in scan modus or when speed is 0 RPM.

K k Turn RIGHT button Press short or Hold Turn the laser clockwise in scan modus or when speed is 0 RPM.

KEYPAD

REMOTE

CONTROL

NAME

FUNCTION

L - LED Slope indicator No Slope modus OFF

Red, continuous Slope modus ON

Red, ashing Laser out of levelling range

M - LED Tilt indicator No Tilt security OFF

Red, ashing slow Preparing TILT security

Red, continuous TILT security active

Red, ashing fast TILT alarm

N - LED Power indicator Green, continuous Power ON

No Power OFF

O - Infrared eye Receives instructions from the remote control.

Always point the remote control to this infrared eye.

SAFETY

Please read the safety instructions provided as

separate booklet with the device.

LASER RADIATION – Class 2 Laser product. – Do

not stare into beam

FIRST TIME USAGE

Remove all protection foils.

The li-ion battery is installed by the manufacturer.

Make sure the battery is fully charged.

Place 2x AAA Alkaline batteries in the remote

control.

BATTERY AND CHARGER

Laser:

This laser works with 2x 7.4V 4000mAh LI-ION

rechargeable battery. To charge this battery, you

can use the provided charger.

The battery is installed by the manufacturer. In

case it needs to be replaced, contact an author-

ised technician.

Remote control:

The remote control works with 2x 1.5V AAA

Alkaline batteries.

AUTOMATIC FUNCTIONS

AUTO-LEVELLING

This rotation laser always levels itself automati-

cally after turning on the device. After being lev-

elled, the laser starts spinning. The laser can level

itself within an operating angle of approx. 5°. The

auto-levelling system performs the necessary ne

adjustments, with the help of 3 electronic meas-

uring sensors, one for each axis (X, Y and Z).

TILT SECURITY

The tilt-security avoids measuring errors. By

default, the laser will be active with the tilt-se-

curity activated. After turning on the laser or

after activating the tilt-security, the tilt-security

is prepared during 60 seconds. During this time

you can install the laser in the sorrect position. 60

seconds after you hit the last button, the tilt-secu-

rity is active.

When the tilt-security sensors detect a small

shock (e.g. a vibration, a gust of wind, ...) the laser

will stop turning and starts ashing and beep-

ing. This give you the opportunity to check if the

laser is still in the correct position after the shock.

You must exit the tilt function, place the laser in

position and restart the laser to continue. A new

preparation process of approx. 60 seconds will

start before the Tilt-security is active.

Tilt-security is the best choice if accuracy is the

most important.

BASIC MODE (TILT-SECURITY OFF)

In the basic mode the laser will stop spinning

if the sensors detect a slight shock, such as a

vibration or gust of wind. The laser will re-level

and automatically start spinning again when it is

levelled again.

This function is a compromise between accuracy

and ef ciency.

USE

Press the power button [A] to activate the device.

NOTE

The choice of the tripod de nes in a large way

the user-friendliness of the device.

If the workplace has a high light intensity, for

example when working outside in a sunny area,

you will need a laser receiver to detect the laser

beam.

HORIZONTAL ALIGNMENT

After turning on the device, the laser light blinks

without spinning. The laser is levelling. When

levelled, the laser beam will light continuously

and the laser will start spinning at 600 RPM, the

optimal speed for usage with a receiver.

By default, the Tilt security will prepare after

turning on the device.

NOTE

The device should not be placed on a surface

with a slope of more than 5°. If this is the case,

the laser is outside the self-levelling range, in

which case the laser diode will continue to blink

and the LED slope indicator [L] will  ash red.

PLUMB LINE

Thanks to the plumb lines, which are projected

via Plumb point up [02] and Plumb point down

[08], this device can also be used to bring a

plumb lead point of the  oor to the ceiling, or

vice versa.

· Mark the starting point.

· Place the laser beam exactly on this starting

point.

· Wait until the laser is levelled.

· Now you can mark the opposite plumb point

accordingly.

VERTICAL ALIGNMENT

Put the device on its feet vertical mode [10] for

vertical alignment (keypad should be on top).

The laser will blink without turning during

levelling. When levelled, the laser beam will light

continuously and the laser will start spinning at

600 rotations per minute, the optimal speed for

usage with a receiver.

NOTE

The device should not be placed on a surface

with a slope of more than 5°. If this is the case,

the laser is outside the levelling range, in which

case the laser diode will continue to blink and

the LED slope indicator [L] will  ash red.

ANGLES OF 90°

90°

In vertical position, it is possible to project angles

of 90°.

· Position the laser head [01] as precise as possi-

ble above the starting point, where the corner

of 90° is made.

It can be helpful to change the spinning speed

to zero when positioning the laser above the

starting point.

·Bring the rotating laser beam to your  rst mark.

You can use the arrow left button [D, d] and

arrow right button [E, e] for  ne tuning.

· The Plumb point up [02] (and Plumb point

down [08]) show each a corner of 90° with the

rotating laser line.

SPINNING SPEED

0 RPM

120 RPM

300 RPM

600 RPM

This device has multiple spinning speeds. 0, 120,

300 and 600 RPM (rotations per minute). The

default rotation speed is 600 RPM.

· Press the speed button [F, f ] to select the

desired speed. Each time you press this button,

the speed will change.

600 - 0 - 120 - 300 - 600 - 0 - …

A speed of 0 RPM projects a stationary laser

point. This can be positioned exactly at the

measuring point with the turn LEFT button [J, c]

or turn RIGHT button [K, b] button.

NOTE

The slower the rotational speed, the better the

visibility with the human eye. A faster rotation

speed is necessary to use a laser receiver

(600 RPM recommended for handheld receiv-

ers.)

SCAN FUNCTION

0 °

10°

45°

90°

180°

The scan function allows to limit the laser beam

to an angle instead of the complete 360° circle.

This creates a light intensive segment that

increase the visibility for the human eye.

Possible angles of the scan function are 0°, 10°,

45°, 90° and 180°.

· Press the scan button [G, g] to select the de-

sired angle of the scan function. Each time you

press this button, the angle will change.

0° - 10° - 45° - 90° - 180° - 0° - 10° - …

You can move the position of the light intensive

segment by pressing the turn LEFT button [J, c]

or turn RIGHT button [K, b] button.

SLOPE FUNCTION

Standard, the instrument shows a 100% horizon-

tal or vertical laser beam. When needed, the laser

can project a sloped laser beam.

To set up slopes, you must take a few steps in the

right order.

NOTE

Keep in mind that auto-levelling is disabled

when working with the slope function.

HORIZONTAL SLOPE, <5°

< 5°

X- and Y-axis

· Place the laser in its horizontal (normal) posi-

tion.

· Position the x-axis [04] and y-axis [05] of the

laser device (shown on the window cover [15])

exactly in the parallel with the direction of the

slope(s) you want to make.

· Turn on the device and wait until it is levelled.

· Choose a distance in the direction of the slope

that needs to be set up. (e.g. 10m)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Futech Livello laser

Futech

Futech 0273DG Manuale utente

Futech

Futech MULTISQUARE 5 Manuale utente

Futech

Futech MULTICROSS 8 Manuale utente

Futech

Futech MULTICROSS 3D COMPACT 030.03D Manuale utente

Futech

Futech MULTICROSS 8 HPSD Manuale utente

Futech

Futech 011.20R Manuale utente

Futech

Futech 906D-20 Manuale utente

Futech

Futech PARA ONE RED Manuale utente

Futech

Futech SATURN 2.0 RED Manuale utente

Futech

Futech MULTICROSS 4D ELECTRONIC Manuale utente

Futech

Futech RED RACER 050.01.1E Manuale utente

Futech

Futech 150.12.TL Manuale utente

Futech

Futech PARA DS RED Manuale utente

Futech

Futech MULTICROSS 8 HIGH PRECISION RED Manuale utente

Futech

Futech MULTICROSS 8 Manuale utente

Futech

Futech Nexus Manuale utente

Futech

Futech PARA ONE RED Manuale utente

Futech

Futech 850.060DM Manuale utente

Futech

Futech EAGLE 32 Manuale utente

Futech

Futech PROCROSS 8.0 DS Manuale utente

Manuali Livello laser popolari di altre marche

Nedo

Nedo ET-5 Manuale utente

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manuale utente

LaserLiner

LaserLiner X2-Laser Manuale utente

Spectra

Spectra LL300N Manuale utente

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manuale utente

Nedo

Nedo Crossliner 4 Manuale utente

Lasertec

Lasertec FX360G Manuale utente

Flex

Flex ALC 8 Manuale utente

Black & Decker

Black & Decker LZR5 Manuale utente

Johnson

Johnson 40-6692 Manuale utente

Cocraft

Cocraft HL 20-SG Manuale utente

Zircon

Zircon iLine Manuale utente

HWH

HWH 310 SERIES Manuale utente

Leica

Leica iCON robot 60 Manuale utente

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manuale utente

LaserLiner

LaserLiner ActiveFinder XP Manuale utente

DeWalt

DeWalt DW082 Manuale utente

imex

imex EL20 Manuale utente