GE GE616 Manuale utente

GE616 Proximity Reader Last Update August 24, 2005

Table of Contents

1. Important safety instructions 3

2. Introduction 5

3. Identifying supplied parts 5

4. Specification 6

5. Installation 6

6. Wire Connection to Controller 7

7. Wire Color Table of the Reader 7

8. Operation 8

9. The Maximum Length of the Wiegand Cable 9

10. FCC Registration Information 10

11. Warranty and Service 11

GE616 Proximity Reader Last Update August 24, 2005

1. Important safety instructions

To prevent injuries to persons and damages to property, please

read all the instructions and follow them whenever you deal

with this product.

After reading, please put this instruction manual where it can be

easily seen for the system operator.

ON INSTALLATION AND POWER

Use 12V DC power ONLY.

- Connecting to higher than 12V DC may result in a risk of

electric shock, fire, or heavy damage

of the unit.

Do NOT install this product at places with wet or metallic dust,

or that can be watered.

- There may be risks of electric shock and fire.

Do NOT install this product near electric motors running.

- The unit may not operate normally.

Do NOT set this product near heaters or anything that

produces heat.

- There may be a risk of fire.

Be ALWAYS careful not to short-circuit any part of the circuitry

with tools like a screwdriver in hand.

- There may be a risk of fire or heavy damage of the unit.

GE616 Proximity Reader Last Update August 24, 2005

ON MAINTENANCE

Do NOT use any kind of liquid for cleaning.

- There may be a risk of electric shock, fire or heavy damage

of the unit.

Use an air spray, if needed.

Users are cautioned NOT to attempt repair of this product or

modify the wirings set by the installer at their own discretion.

- It may pose the risk of fire, hardware damages, or abnormal

operations of the unit.

It is recommended not to use a flammable spray or some-

thing easy to burn near this product.

- There may be the risk of an explosion or fire.

Keep the unit away from any unauthorized people.

- It may cause abnormal operations of the unit.

NOTICE

Please, contact a designated service center or the outlet at

which the product was purchased when

A. Any liquid has been spilt or sprayed onto the product.

In this case, cut the power off first.

B. The product seems to be operating abnormally.

C. The unit exhibits a distinct change in performance.

D. The unit has fallen to be broken down or damaged on

its case.

* The cost of repairing can be charged for troubles due

to the improper handling or negligence of users or

the operator.

GE616 Proximity Reader Last Update August 24, 2005

2. Introduction

The GE616 is an elegant looking and an attractive 4" read

range proximity reader which can be mounted to metal door

frame (mullion) or any flat wall surface. The GE616 is epoxy

potted that ensure you successful operation even in harsh

environments. Two colors LED of green and red, inside Piezo

buzzer sound will guarantee you an accurate and reliable

system operations.

3. Identifying supplied parts

Please unpack and check the contents of the box.

Reader

Module

GE616

Bezel Manual Screws

(1ea) (1ea) (1 copy) (4ea)

GE616 Proximity Reader Last Update August 24, 2005

4. Specification

5. Installation

5-1. Mullion/Wall Mount

Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical

and drill one 1/2" hole for the reader cable 1.7"(4.31cm) apart

from the top hole.

(If you have installed electric gang box then skip this step.)

5-2. Put reader cable into the center hole and install the

reader module by using two 6-32 or M3 screws.

5-3. Put bezel into the reader module then push bezel until you

hear the locking sound.

Read Range/Time Up to 4"(10cm) / 30ms

Input Voltage/Current DC 5V ~ 17V, Max. 100mA

Output Format 26 bit Wiegand

External Buzzer

Control Input

Low Active, DC 0 ~ 12V,

Max. 50mA

External LED

Control Input

Low Active, DC 0 ~ 12V,

Max. 50mA

LED/Buzzer 2 Color LED (Red and Green) / Piezo

Buzzer

Color Silver

Operating

Environment

-31 ~149(℉℉-35 ~ +65 )℃℃

10~90% Humidity, Non-Condensing

Overall Size (WxHxD) 1.82"x4.81"x0.87"(46x122x23mm)

Weight 0.35lb(160g)

GE616 Proximity Reader Last Update August 24, 2005

6. Wire Connection to Controller

GE616 Proximity Reader Last Update August 24, 2005

7. Wire Color Table of the Reader

POWER

Power(DC +5V~+17V) DC(+)

Red wire

Power(DC Ground) DC(-)(GND)

Black wire

INPUT

Buzzer control input

BUZZER Blue wire

LED control input LED

Yellow wire

OUTPUT(Wiegand Format)

Wiegand Data-0 Data-0

Green wire

Wiegand Data-1 Data-1

White wire

8. Operation

8-1. Apply power and you can see Red LED is on indicating the

reader is in standby.

8-2. Present proximity card to the reader until you hear beep

sound and the LED is changing the color to Green

simultaneously and the reader send RF card data to the

controller then LED changes the color to Red again for next

reading.

8-3. LED Control

To change the LED colors, you may connect LED Control

Input (Yellow wire) to power ground then the Green LED is

on indicating the reader is in standby.

Present proximity card then the LED changes the color

to Red simultaneously then Green again for next reading.

GE616 Proximity Reader Last Update August 24, 2005

8-4. Buzzer Control

When the reader reads proximity card, only one beep sound

generates in normal operating mode but you can generate

more beep sounds to distinguish whether the access is

granted or denied.

To generate more beeps, you may control the Buzzer

Control Input(Blue wire) to power ground then you can turn

beeper on while you hold Buzzer Control Input to power

ground.

9. The maximum length of the Wiegand cable

When use this reader with controller, length of the Wiegand

cable is maximum 150m on the following condition.

•Controller and Cable

- Controller : GE313 or GE314

- Cable : AWG #22 twisted pair

GE616 Proximity Reader Last Update August 24, 2005

10. FCC Registration Information

FCC REQUIREMENTS PART 15

Caution: Any changes or modifications in construction of this device

which are not expressly approved by the responsible for compliance

could void the user's authority to operate the equipment.

NOTE: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1. This device may not cause harmful interface, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A Digital Device, pursuant to Part 15 of the FCC Rules.

These limits are designed to this equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the

radio or television off and on, the user is encouraged to try to correct

interference by one or more of the following measures.

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on another circuit.

4. Consult the dealer or an experienced radio/TV technician for help.

Indice

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente