GSM Activate AD-SD Manuale utente

PAGE1

Our AD-SD Auto Dialler is a versatile unit which can be attached to many of your

electronic devices in your homes; work, gardens or wherever you may need it. It will alert

you using GSM technology by sending you a text message or phone call to your mobile

phone or land line. Therefore alerting you immediately to a problem, failure or status

change wherever you are in the world!

Our AD-SD-W WIRELESS version has wireless capabilities to make it a standalone alarm

using various wireless sensors.

Our Auto-Dialler is set apart from other models on the market by being on the

quad band frequency meaning it an be used worldwide and we frequently ship models all

over Europe, USA and Australia with excellent feedback.

The unit is also enclosed in a IP65 rated box which means it is perfectly weathered for

outside installation and has passed testing in high temperature and below freezing

conditions.

GSM Frequency: Quad band freq 850/900/1800/1900/ 3g only model 2100 Mhz.

Power Supply Voltage: 9 - 24 volts DC - 1 Amp Max

Current used in standby mode: 60mA Max

IP 65 Enclosure rating for outside installation

2 Inputs Neg triggered

1 Inputs poss triggered

8 Amp Relay Output

Micro Simcard

No land line required

Dimensions - L150 x W90 x H45mm

Dimensions PCB Only - L125 x W67mm

Sim Active Function

Operating Temperature: -10...+40°C

Programmed by Text / SMS Message

Text to test signal strength

2G OR 3G Model

Wireless Alarm Function

Activate Alarm via text message

RF 433mhz transmission /receiver —- Code EV1527

Range 10 metres line of sight

Page 2

INSTRUCTIONS

To help make sure that you place the unit in a suitable position you can text the unit to see

how much signal strength the dialler is receiving by texting the command

The dialler will perform a test on the signal strength.

You will receive a text telling you a signal strength score between 0 up to 30 we strongly

recommend that you place the unit where you can receive a signal strength score of at least

10. You will find that with a score of less than 10 the unit will be unreliable.

Page 3

Slide the simcard into the holder making sure that the clipped corner of the simcard

lines up with the clipped corner of the simcard holder as picture above.

Dipswitch 2 ON= Relay Mode on

2 OFF= Relay Mode off Ref page 6

After inserting your simcard into the Auto-Dialer turn the unit on and wait until you see the

LED is on. This will indicate that you have a mobile signal and the unit is

ready for use.

You will now need to send a text with the contact number

Note - To avoid confusion we have colour coded the hash (#) and the equals (=) symbols.

Ex a mp le : (h a s h ) (1 o r 2 o r 3) (e q u a ls ) (p h o n e n u mb e r) (h a s h )

then send this as a text to the simcard number of your unit

If you wish to cancel a number follow this example

Ex a mp le : (h a s h ) (1 o r 2 o r 3) (e q u a ls ) (DELETE) (h a s h )

Then send this as a text to the simcard number of your unit

Please send one message at a time and wait for the Auto Dialler to send you back the text

Acknowledgement ‘NUMBER STORED’ before you try to add another number.

Below is a notepad to help you remember the numbers that you have saved to your

unit in the event you need to modify or delete in the future.

#1=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

#2= _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

#3=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #

Page 4

You can now change the alarm message for inputs 1 & 2 to your own choosing.

To change the message send the text command as follows.

The default message is (

This will change the message to

The auto dialler can be programmed to send you a telephone call after each text alarm

has been sent.

You will receive approximately three ring tones. The unit will then hang up automatically.

This is to prevent call charges being incurred.

To set call alerts to ON please send the text message

The unit will reply back “call on”

To disarm call alerts please send the text message.

If the call function has been set to you will receive a text message and shortly after a

phone call.

Page 5

Page 6

ref page 3

The Auto Dialler has a 8 amp volt free contact relay output which can be used to switch

on external electric devices such as lighting, sirens etc.

By texting the unit you can turn the relay ON or OFF. Below are examples on how to do

this.

- This will turn on relay output

-This will turn off relay output

After each operation the unit will reply with a status report

ref page 3

The relay can also be setup to pulse for 20 seconds when the inputs have been triggered.

To activate this mode you need to set to the position. Ref page 3

This can be used to reset auxiliary equipment.

The Auto Dialler has two independent input’s

Input 1 = Terminal 1 connection. (Negatively triggered) pulled to ground

Input 2 = Terminal 2 connection. (Negatively triggered) pulled to ground

When the inputs are triggered the will flash 6 times to indicate that a

trigger has been received and it will send a text / call message to the saved user numbers.

Both Input 1, and Input 2, can be triggered independently.

The Auto_dialler will reset automatically when the triggered input is released.

Can be triggered with a positive supply 12v/24v refer to page 9

Page 7

Typical Application of Product

Security alarm system applications

Supervision and monitoring alarm systems

Automatic monitoring system

Vending machines security protection

Buildings and real estate

Weather stations

River monitoring and flood control

Fridges/Fish Tanks

Farming equipment and security

Dipswitch settings

Dipswitch 1 = ON = 3G Selected

OFF = 2G Selected

Dipswitch 2 = ON= Relay Mode on

OFF= Relay Mode off

To reset the unit back to factory settings you will need to send a text message

Warning this will reset all of your parameters, only send a reset command when necessary.

The green ready led will flash 8x

Note - Dipswitch 1 not used on 2G only Model

Model AD-SD-W WIRELESS has an RF module which allows connection to various wireless

sensors, that will then trigger the dialler in the same way as hard wiring into input 1 and input 2.

To connect wireless sensors you will need to go through a process so that the devices

are matched to the receiver on the dialler.

Typical Process (can vary dependent on sensor)

1. Switch on the Auto Dialler.

2. Switch on the sensor and allow it to warm up for 15 seconds.

3. Hold down the pairing button on the RF Module for 3 seconds (refer to figure 1).

4. Trigger the sensor.

5. The RF module has a red LED which will flash when pairing is Complete.

: Hold down the pairing button on the RF Module for 3 seconds (refer to figure 1).

7. Trigger the door switch.

8. The RF module has a RED LED which will flash when pairing is Complete.

Once the sensors are paired, you can now send a text command to activate the alarm.

This will activate the alarm.

This will deactivate the alarm.

When sensors/door detect movement You will receive a text message (

Note :The alarm will need to be re activated again once it has been triggered, the alarm message

cannot be changed from ALARM TRIGGERED.

Please Note: Ensure you have already setup your

contact numbers as per instructions on page 4

Figure 1

INPUT 1+2

As you can see in the circuit diagram above the inputs can be activated by

pulling the input 1 & 2 to ground. Alternatively input 2 only can be positively triggered by

using terminal 3.

Re la y Ou tp u t Volt free contact

The relay has Common, Normally Open and Normally Closed contacts which are capable

of 8 Amp loads. This is suitable for turning ON or OFF electrical equipment. Alternatively

it can be used for resetting your alarm system.

The relay can be manually activated by text message commands or it can be set to pulse

for 20 seconds when an input has been activated - refer to page 6

PAGE 9

Please make sure you supply a 9 - 24 volts DC from the battery terminals via a 2

amp fuse (for alarm panel installations)

For more technical support please browse the FAQ’s on our website

Alternatively email our technical support team at and we

will do our best to reply within 24 hours Monday - Friday.

05/06/2018 AD

Altri manuali per AD-SD

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GSM Activate Unità di controllo

GSM Activate

GSM Activate AD4IN1V8 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente