GW Instek PEL-2002 Manuale utente

Programmable DC Electronic

Load

PEL-2000 Series

USER MANUAL

GW INSTEK PART NO. 82EL-20040MA1

ISO-9001 CERTIFIED MANUFACTURER

March 2010

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of the Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

right to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng City, Taipei County 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS ................................................... 5

GETTING STARTED......................................................... 10

Main Features ...................................... 12

Series Overview ................................... 13

Package Contents and Accessories....... 15

Measurement Overview ....................... 16

Front Panel Overview........................... 17

Display Overview – Mainframe ............ 22

Rear Panel Overview ............................ 25

Front Panel Overview – Load Module... 28

LED Display Overview – Load Module.. 32

Installation .......................................... 35

Load Connections ................................ 43

Frame Link Connection ........................ 54

Channel Control Connection ................ 56

Go/NoGo Connection .......................... 59

OPERATING DESCRIPTION............................................. 60

Operating Mode Description ............... 61

Run Program........................................ 71

Sequence ............................................. 74

Parallel Dynamic Loading .................... 78

Configurations Description .................. 79

Interface and File System..................... 89

TUTORIALS..................................................................... 96

Local loads .......................................... 97

Single Channel Load ............................ 99

Programming..................................... 101

Sequences.......................................... 103

PEL-2000 Series User Manual

Frame Link ......................................... 104

Channel Control................................. 106

General Configuration Options .......... 108

OPERATION...................................................................109

Local Mode Operation ....................... 112

Mainframe Basic Operation ............... 119

Channel Configuration ....................... 160

Mainframe Configuration ................... 180

Interface Configuration (settings) ...... 195

Save / Recall ...................................... 201

INTERFACE ....................................................................232

Interface Configuration ...................... 233

FAQ ...............................................................................241

APPENDIX .....................................................................242

Fuse Replacement .............................. 242

Battery Replacement .......................... 243

Firmware Update ............................... 244

Calibration ......................................... 245

Range Chart ....................................... 246

Default Settings ................................. 251

Specifications .................................... 253

Dimensions ....................................... 261

EC Declaration of Conformity............. 263

INDEX............................................................................264

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow when operating

the PEL-2002/PEL-2004, and when keeping it in

storage. Read the following before operating the

PEL-2002/2004 to ensure your safety and to keep

the PEL-2000 series in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the PEL-

2002/2004.

WARNING Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION Caution: Identifies conditions or practices that

could result in damage to THE PEL-2002/2004 or

to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

PEL-2000 Series User Manual

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the PEL-

2002/2004.

Avoid severe impact or rough handling that

leads to damaging the PEL-2002/2004.

Do not discharge static electricity to the PEL-

2002/2004.

Do not block or obstruct the cooling fan vent

openings.

Do not perform measurement at circuits directly

connected to Mains (Note below).

Do not disassemble the PEL-2002/2004 unless

you are qualified as service personnel.

The equipment is not for measurements

performed for CAT II, III and IV.

(Measurement categories) EN 61010-1:2001 specifies the

measurement categories and their requirements as follows. The

PEL-2002/2004 falls under category I.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Measurement category I is for measurements performed on

circuits not directly connected to Mains.

SAFETY INSTRUCTIONS

Power Supply

WARNING

AC Input voltage: 115V/230V switchable,

50/60Hz

The power supply voltage should not fluctuate

more than 15%.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

Fuse

WARNING

Fuse type: T3.15A/250V

Make sure the correct type of fuse is installed

before power up.

To avoid fire, only replace the fuse with the

specified type and rating.

Disconnect the power cord before fuse

replacement.

Make sure the cause of a fuse blowout is fixed

before replacing the fuse.

Battery

WARNING

Battery type: CR17345 (See page 243).

When replacing the battery ensure that the

correct make and model are used.

Cleaning the

PEL-2000

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals or cleaners containing

harsh material such as benzene, toluene, xylene,

and acetone.

PEL-2000 Series User Manual

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Altitude: Up to 2000m

Transient Overvoltage on the main supply is

2500V.

(Pollution Degree) EN 61010-1:2001 specifies the pollution degrees

and their requirements as follows. THE PEL-2002/2004 falls under

degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Relative Humidity: < 80%

Temperature: −10°C to 70°C

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the PEL-2002/2004 in the United Kingdom, make sure

the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow: Earth

Blue: Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with the coloured

marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth

terminal marked with either the letter E, the earth symbol or coloured

Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is

marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked

with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact the

supplier.

This cable/appliance should be protected by a suitably rated and approved

HBC mains fuse: refer to the rating information on the equipment and/or user

instructions for details. As a guide, a cable of 0.75mm2 should be protected by a

3A or 5A fuse. Larger conductors would normally require 13A types,

depending on the connection method used.

Any exposed wiring from a cable, plug or connection that is engaged in a live

socket is extremely hazardous. If a cable or plug is deemed hazardous, turn off

the mains power and remove the cable, any fuses and fuse assemblies. All

hazardous wiring must be immediately destroyed and replaced in accordance

to the above standard.

PEL-2000 Series User Manual

GETTING STARTED

This chapter describes the features and functions of the

PEL-2002/2004, including the front and rear panel

appearance, panel installation and connection types. Use

the Tutorial section for quick access to step by step

instructions on the main functions.

Main Features ................................................................. 12

Series Overview............................................................... 13

Package Contents and Accessories .................................. 15

Measurement Overview................................................... 16

Front Panel Overview ...................................................... 17

Display Overview – Mainframe ........................................ 22

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali GW Instek Apparecchiature di prova

GW Instek

GW Instek GCP-300 Manuale utente

GW Instek

GW Instek GPT-9000 series Manuale utente

GW Instek

GW Instek GLC-9000 Manuale utente

GW Instek

GW Instek GUT-6000A Manuale utente

GW Instek

GW Instek GLC-10000 Manuale utente

GW Instek

GW Instek GDS-1000A Series Manuale del proprietario

GW Instek

GW Instek GDS-1000A-U Series Manuale utente

GW Instek

GW Instek PEL-2000A Series Manuale utente

GW Instek

GW Instek GOS-620FG Manuale utente

GW Instek

GW Instek GPT-9801 Manuale utente

GW Instek

GW Instek GCT-9040 Manuale utente

GW Instek

GW Instek PEL-3000 Series Manuale utente

GW Instek

GW Instek GDS-3352A Manuale utente

GW Instek

GW Instek GDS-820 Programming Manuale del proprietario

GW Instek

GW Instek GDM-SC1A Manuale utente

GW Instek

GW Instek GLC-9000 Manuale utente

GW Instek

GW Instek GDS-2000 Series Manuale utente

GW Instek

GW Instek MDO-2000A Series Manuale utente

GW Instek

GW Instek MDO-2000E Series Manuale utente

GW Instek

GW Instek GPT-9800 Manuale utente

GW Instek

GW Instek GDS-1000-U Series Manuale utente

GW Instek

GW Instek GDS-1062A Manuale utente

GW Instek

GW Instek GDS-2000A Series Manuale utente

GW Instek

GW Instek PEL-3000E Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente