Gymstick GT4.0 Manuale utente
GT4.0 TREADMILL
USER MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future
reference. The specications of this product may vary from this photo, subject to change without notice.
2GT4.0 TREADMILL
BEFORE YOU BEGIN
Thank you for choosing the Gymstick GT4.0 Treadmill. We take great pride in producing this quality
product and hope it will provide many hours of eective exercise to make you feel better, look
better and enjoy life to its fullest.
TABLE OF CONTENT
1. SAFETY INSTRUCTIONS ................................................................................................ 3
2. ASSEMBLY INSTRUCTION............................................................................................... 4
3. MOVING TREADMILL........................................................................................................ 8
4. IMPORTANT ELECTRICAL INFORMATION ..................................................................... 9
5. CONSOLE OPERATION INSTRUCTIONS .................................................................... 10
6. MAINTENANCE AND CARE ............................................................................................. 15
7. LUBRICATING THE TREADMILL ...................................................................................... 17
8. TROUBLESHOOTING ....................................................................................................... 18
9. EXPLODED DRAWING ..................................................................................................... 20
10. PARTS LIST ...................................................................................................................... 21
11. IMPLIED WARRANTY ...................................................................................................... 24
READ AND FOLLOW THE SAFETY INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS
CAN RESULT IN SERIOUS INJURY.
!
NOTIFICATION!
3GT4.0 TREADMILL
!
WARNING!
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety instructions when using
this equipment: Read all instructions before using this equipment.
• Never leave the treadmill unattended. Unplug the unit from the power outlet when it is not in use.
• Do not allow children or those unfamiliar with its operation on or near the treadmill. Do not leave children or
persons with reduced physical or mental capabilities unsupervised around the treadmill.
• Please wear proper clothes and shoes when using this equipment; do not wear clothes that might catch
any part of the equipment.
• If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately
and consult your physician before continuing.
• Keep children and pets away from the equipment. This machine is designed for adults only.
• Only one person should be on the equipment while in use.
• Please make sure all parts are not damaged and xed well before use.
• Never operate the unit if it is damaged, if it is not working properly
• This equipment should be placed on a at surface when using. Using a mat or other covering material on
the ground is recommended. The minimum free space required for safe operation is 0,5 meter.
• Never block the air openings on the hood while operating the treadmill. Never drop or insert objects into
any opening.
• Use the treadmill only for its intended purpose as described in this manual.
• If the power cord of the machine is damaged, it must be replaced. Do not use the machine until the power
cord has been changed and properly attached.
• This equipment is for household use only. Do not use the equipment outdoors.
• This appliance is designed for use with ~220 - ~240 Volt rated voltage.
• The maximum weight capacity for this product is 120kgs.
BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN FIRST.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH
PRE-EXISTING HEALTH PROBLEMS.
4GT4.0 TREADMILL
ASSEMBLY INSTRUCTION
• Lift up and remove the box that surrounds the Treadmill.
• Check the following items are present. If any of the parts are missing, contact with the dealer.
Note: Each step number in assembly instructions tells you what you will be doing. Read and
understand all instructions thoroughly before assembling the treadmill.
!
WARNING!
USE CAUTION WHEN ASSEMBLING THIS TREADMILL. FAILURE MAY RESULT IN INJURY.
䈤᰾Җ
0;
0;
0;
0;
0;
MAIN BODY UPRIGHT POST (R/L) HARDWARE KIT
CONSOLE SAFETY KEY SILICONE BOTTLE MANUAL
ALLEN SCREW (M8x50x20) 4PCS L-SHAPE SPANNER S5 1PCS
HEXAGON SOCKET HEAD BOLT (MX20) 4PCS L-SHAPE SPANNER S6 1PCS
TAB BOLT 1PCS INNER HEXAGON BOLT (M8x20) 4PCS
5GT4.0 TREADMILL
ASSEMBLY INSTRUCTION
TREADMILL OVERVIEW
Rear cover
Console
Handle bar
Safety key
Upright post
Motor cover
Side rail
Running belt
Maximum load 120kg
Dimension (folded) 1104 x 815 x 1450mm
Dimension (unfolded) 1711 x 815 x 1389mm
Running surface 1420 x 500mm
Speed 1.0 - 18.0km/h
TECHNICAL INFORMATION
REMARK: We reserve the right to amed the product without prior notice.
6GT4.0 TREADMILL
ASSEMBLY INSTRUCTION
STEP 1
Take out the machine from box and put it on the at oor. (As shown),remove all PE bags and bags
wrapped on the machine.
STEP 2
Fold the machine up to make sure that the non-return pipe is rmly fastened. Take out the left and
right upright post, and use two inner Allen C.K.S.half thread screw tighten from the inside and out
respectively. Use a M8*20 with inner hexagon bolts from top to bottom for locking!
Note: when installing the right riser, pay attention to properly connecting the communication line
between the riser and the base, and avoid clamping it!
7GT4.0 TREADMILL
ASSEMBLY INSTRUCTION
STEP 3
Press the non-return pipe to expand the running table, take out the console and assembly it as
shown below! After aligning the hole position from inside to outside use the M8*20 Allen C.K.S. full
thread screw to lock in!
STEP 4
Lift up the console and x it from the left side of the watch with a TAB bolt.
8GT4.0 TREADMILL
ASSEMBLY INSTRUCTION
STEP 5
Finally, check the machine screw is locked. After all the screws are fastened, the machine installati-
on is completed.
MOVING THE TREADMILL
9GT4.0 TREADMILL
IMPORTANT ELECTRICAL INFORMATION
This treadmill requires a right power source in order to properly operate. For your safety, as well as the
safety of others, please verify that the power source is correct before plugging the equipment. Any incorrect
power source could cause signicant damage to the equipment and or user.
GROUNDING METHODS:
This product must be grounded. Grounding provides the least resistance for electrical current and will
reduce the risk of electric shock. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances. Ensure that the product is
connected to an outlet which contains the same conguration as the plug. Do not use an adaptor for this
product.
This product is for use on a nominal circuit and has a grounding plug that looks like the plug illustrated in the
below picture. Make sure that the product is connected to an outlet having the same conguration as the
plug. No adapter should be used with this product.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with
a certied electrician if you are in doubt as to whether the product is properly grounded. Do not modify the
plug provided with the product. If it will not t the outlet, have a proper outlet installed by an electrician.
1. NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power cord
away from any moving part of the treadmill including the elevation mechanism and transport wheels.
2. NEVER operate the treadmill using a generator or UPS power supply.
3. NEVER remove any cover without rst disconnecting power.
4. NEVER expose the treadmill to rain or moisture. This treadmill is not designed for use outdoors, near
pools or in any other high humidity environment
!
WARNING!
!
DANGER!
!
WARNING!
10GT4.0 TREADMILL
CONSOLE OPERATION INSTRUCTIONS
CONSOLE FUNCTION INSTRUCTION
1. P0 is manual program for user. P1-P36 is for the built-in automatic training program, three
user’s “U” and FAT program.
2. 0.56 inch LED display screen, 12 touch operation keys;
3. Running speed range:1.0~18.0KM/H, inclination: 0-15%
4. Self-test System, abnormal information prompt function.
5. Speed, distance conversion function
6. MP3 (optional)
7. HRC
8. Bluetooth
DISPLAY WINDOW INSTRUCTION
1. SPEED and PULSE to show the value of the velocity and the heart rate
2. TIME and CALORIES to show time, calorie value
3. DISTANCE and INCLINE to show distance and ascension data
KEYBOARD OPERATION INSTRUCTION
1. PROG: Program selection key, stop state, loop selection program P1~P36, U01, U02, U03
and FAT.
2. MODE: When selected to the initial state of is normal mode, press mode key can cycle
select the manual mode of countdown mode-> counting calorie mode-> inverted distance
mode -> positive timing mode; Reset key in P01-P36 for default value (30 minutes) between
countdown.
3. START/STOP: Start / stop key, start the treadmill in the stop state, stop the treadmill in the
running state.
4. + Speed pass key: In the state of stopping or measuring fat, adding keys for setting
parameters and adding keys for speed in running state.
5. - The speed decline key, in the state of stopping or measuring fat, is the key of setting the
parameter decline, and in the running state, it is the key of the decline of the speed.
Indice
Altri manuali Gymstick Tapis roulant
Gymstick
Gymstick RUN 3.0 Manuale utente
Gymstick
Gymstick PRO20.0 Manuale utente
Gymstick
Gymstick GT1.0 Manuale utente
Gymstick
Gymstick RUN 10.0 Manuale utente
Gymstick
Gymstick PRO20.0 Manuale utente
Gymstick
Gymstick PRO10.0 Manuale utente
Gymstick
Gymstick WalkingPad TM-WPAD Manuale utente
Gymstick
Gymstick TITANIUM RUN 2.0 Manuale utente
Gymstick
Gymstick GT3.0 Manuale utente
Gymstick
Gymstick GT7.0 Manuale utente
