H3C SecPath PSR300-12A2 Manuale utente

H3C SecPath PSR300-12A2 &

PSR300-12D2 Power Modules

User Manual

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W102-20200303

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this

document are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Preface

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the the H3C SecPath PSR300-12A2 & PSR300-12D2.

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Overview························································································1

Views······································································································································1

Technical specifications···············································································································2

LEDs·······································································································································2

Installing and removing the power supply ··············································3

Safety precautions ·····················································································································3

Tools·······································································································································3

Installing and removing the power supply························································································3

Installing the power supply ····································································································3

Connecting the power cord····································································································4

Removing the power supply···································································································5

Overview

The PSR300-12A2 is an AC-input and DC-output power supply. The PSR300-12D2 is a DC-input

and DC-output power supply. They provide a maximum output power of 300 W.

The PSR300-12A2 and PSR300-12D2 power supplies have the following features:

•Provide protection against input overcurrent, input undervoltage, output overvoltage, output

short-circuit, and overtemperature.

•Support for 1+1 redundancy and load sharing.

•Hot swappable. You can hot swap a power supply when another power supply is operating.

Views

Figure 1 PSR300-12A2

(1) Power switch ("O" represents off and "—" represents on)

(2) Power receptacle (3) Air vent

(4) Handle (5) Power output status LED

(6) Power input status LED (7) Securing holes for the power cord retaining clasp

(8) Fastening screw

Figure 2 PSR300-12D2

(1) Power switch ("O" represents off and "—" represents on)

(2) Power receptacle (3) Air vent

(4) Handle (5) Power output status LED

(6) Power input status LED (7) Screw holes for securing the power cord connector

(8) Fastening screw

Technical specifications

Table 1 Technical specifications

Item Specifications

Rated input voltage •PSR300-12A2: 100 VAC to 240 VAC

•PSR300-12D2: –48 VDC to –60 VDC

Output voltage 12 V

Maximum output current 25 A

Maximum output power 300 W

Dimensions (H × W × D) 40.13 × 101.6 × 234.9 mm (1.58 × 4.00 × 9.25 in)

Operating temperature 0°C to 55°C (32°F to 131°F)

Operating humidity 5% RH to 95% RH, noncondensing

LEDs

The power supply uses power input and power output LEDs to indicate the power input and output

status, respectively.

Table 2 LED description

LED Status Description

Power input status LED (AC OK or Input) Off No power is being input or an input failure has

occurred.

On Normal power input.

Power output status LED (DC OK or

Output) Off No power is being output or an output failure has

occurred.

On Normal power output.

If the power input LED is on but the output LED is off, an output issue or an overtemperature

condition might have occurred. To resolve the issue:

1. Turn off the power switch and disconnect the power cord. Then reconnect the power cord and

turn on the power switch.

This operation resolves the power supply failure caused by an output overvoltage, output

short-circuit, or output overcurrent condition. The power supply shuts down and latches off if

one of these conditions occurs and cannot automatically restore operation.

2. If the issue persists, the temperature might be high. Take measures to decrease the

temperature to an acceptable range. The power supply will automatically restore operation.

Installing and removing the power supply

Safety precautions

To avoid possible bodily injury and power supply and device damage, follow these safety

precautions:

•When installing and removing the power supply, always wear an ESD wrist strap and makesure

it makes good skin contact.

•Make sure the voltage of the power source is as required by the power supply, and the output

voltage of the power supply is as required by the device.

•To avoid bodily injury, do not touch any bare wire or terminal.

•Do not place the power supply in a wet location, and prevent liquid from flowing into the power

supply.

•To avoid power supply damage, do not open the power supply. If the internal wires or units are

faulty, contact H3C Support.

Tools

When installing and removing a power supply and power cord, you must wear an ESD wrist strap.

Prepare it yourself.

Installing and removing the power supply

The installation and removal procedures are similar for the PSR300-12A2 and PSR300-12D2 power

supplies. The following procedures install and remove a PSR300-12D2 power supply.

Installing the power supply

CAUTION:

To avoid bodily injury and device damage, strictly follow the procedure in Figure 3 to install the

power supply.

Figure 3 Power supply installation procedure

Install the power supply

Connect the power cord

Turn on the circuit breaker

Start

End

To install the power supply:

1. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably

grounded.

2. Unpack the power supply and make sure the power supply model is as required.

Keep the power supply package secure for future use.

3. As shown in Figure 4, correctly orient the power supply (with the lettering on it upwards).

Grasping the module handle with one hand and supporting the module bottom with the other,

push the module slowly into the slot along the guide rails. Make sure the power supply has good

contact with the backplane connectors.

The power supply and power supply slot are designed to prevent disorientation and

misalignment. If you cannot insert the power supply smoothly into the slot, the orientation might

be wrong or the power supply is not aligned correctly with the slot. Pull out the power supply,

reorient the power supply or realign it with the slot, and insert it again.

4. When the power supply is fully seated in the slot, fasten the screw on the power supply.

Figure 4 Installing the power supply

Connecting the power cord

Connecting the AC power cord

WARNING!

•Make sure each power cord has a separate circuit breaker.

•Before connecting a power cord, turn off the circuit breaker for it.

To connect the AC power cord:

1. As shown in Figure 5, pivot up the power cord retaining clip, insert the female connector of the

AC power cord into the AC-input power receptacle on the power supply, and then pivot down

the power cord retaining clip.

Figure 5 Connecting the AC power cord to the power supply

2. Connect the other end of the AC power cord into an AC power source, and turn on the circuit

breaker for the power cord.

3. Turn on the power switch. If the AC OK LED is on, the power cord is connected correctly. If the

AC OK LED is off, the connection might be wrong. Verify the installation and resolve the issue.

Connecting the DC power cord

1. As shown in Figure 6, insert the connector of the DC power cord into the DC-input receptacle on

the power supply. Then fasten the screws on the connector.

The connector of the DC power cord and the DC-input receptacle are designed to prevent

disorientation. If you cannot insert the connector smoothly into the receptacle, the orientation

might be wrong. Remove the connector, reorient it, and connect it again.

2. Use a releasable cable tie to secure the power cord to the handle of the power supply.

Figure 6 Connecting the DC power cord

3. Connect the other end of the DC power cord to a DC power source.

4. Turn on the power switch on the power supply. If the Input LED is on, the power cord is

connected correctly. If the Input LED is off, the connection might be wrong. Verify the

installation and resolve the issue.

Removing the power supply

CAUTION:

To avoid bodily injury and device damage, strictly follow the procedure in Figure 7 to remove the

power supply.

Figure 7 Power supply removal procedure

To remove the power supply:

1. Turn off the circuit breaker for the power cord.

2. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably

grounded.

3. Turn off the power switch.

4. Loosen the releasable cable tie that secures the power cord to the handle of the power supply.

5. Loosen the screws on the power cord connector and then remove the power cord.

Figure 8 Removing a DC power cord connector

(1) Loosen the screws on the power cord connector

(2) Pull the connector out

6. As shown in Figure 9, loosen the screwon the power supply. Grasping the powersupply handle

with one hand, pull the power supply part way out of the slot. Supporting the power supply

bottom with the other, pull the power supply slowly out of the slot along the guide rails.

Altri manuali per SecPath PSR300-12A2

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali H3C Unità di controllo

H3C

H3C LSQM1CGS2QSA0 Manuale utente

H3C

H3C NSQ1TGS32SF0 Manuale utente

H3C

H3C NSQ1FAB04B0 Manuale utente

H3C

H3C S9500 LSB1FW2A0 Manuale elenco delle parti

H3C

H3C PSR250-12A Manuale utente

H3C

H3C S9500 LSB1LB1A0 Manuale utente

H3C

H3C SecPath NSQ1FAB08D0 Manuale utente

H3C

H3C SecPath NSQM2GP24TSSC0 Manuale utente

H3C

H3C PSR1800-56A Manuale utente

H3C

H3C S9500E Series Manuale elenco delle parti

H3C

H3C PSR450-12A Manuale utente

H3C

H3C PSR750-A Manuale utente

H3C

H3C SIC-4G-CAT6 Manuale utente

H3C

H3C PSR450-12A Manuale utente

H3C

H3C PSR300-12A Series Manuale utente

H3C

H3C SR6600 SPE-FWM Manuale utente

H3C

H3C SecPath AC2500 Manuale utente

H3C

H3C S12500 LST1LB1A1 Manuale utente

H3C

H3C SFP-GE-SX-MM850-A Manuale utente

H3C

H3C PSR6000 Manuale utente

H3C

H3C LSVM1S9800FAN Manuale utente

H3C

H3C SR6600 SPE-FWM-200 Manuale utente

H3C

H3C MSR Router Comware 5 Series Manuale utente

H3C

H3C LSVM2106SFAN Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente