H3C UAP380 Manuale utente

H3C UAP380 Access Point

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 5W100-20180126

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE,Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C UAP380 Access Point Installation Guide guides you through the installation of your AP. It

covers product overview, preparing for installation, installing theAP, and LEDs and ports.

This preface includes the following topics about the documentation:

•Audience

•Conventions

•Obtaining documentation

•Technical support

•Documentation feedback

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the UAP380 AP.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

Convention Description

> Multi-level menus are separated by angle brackets. For example, File > Create >

Folder.

Symbols

Convention Description

WARNING! An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION: An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT: An alert that calls attention to essential information.

NOTE: An alert that contains additional or supplementary information.

TIP: An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.



Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website at

http://www.h3c.com.hk

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

service@h3c.com

http://www.h3c.com.hk

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Preparing for installation ····································································1

Safety recommendations ·············································································································1

Temperature and humidity requirements ·························································································1

Accessories provided with the AP··································································································1

Installation tools·························································································································2

Installing the AP···············································································3

Installation flowchart ···················································································································3

Pre-installation tasks···················································································································3

Determining the installation position ·······························································································3

Installing the AP ························································································································4

Mounting the AP on a table ···································································································4

Mounting the AP on a wall·····································································································4

Connecting the AP to the power source ··························································································7

Check after power-on ···········································································································8

Connecting the AP to an IoT module ······························································································8

Installing an antenna···················································································································9

Verifying network connection for the AP························································································ 10

Appendix A Technical specifications··················································· 11

Appendix B Ports and LEDs ·····························································12

Ports ····································································································································· 12

LEDs····································································································································· 13

Index ···························································································15

Preparing for installation

Safety recommendations

WARNING!

Only qualified personnel can install and remove the AP and its accessories. You must read all

safety instructions before installation and operation.

To avoid possible bodily injury and equipment damage, read the following safety recommendations

before installing the AP. Note that the recommendations do not cover every possible hazardous

condition.

•Take adequate safety measures to avoid body injury and AP damage.

•Place the AP in a dry and flat location and take anti-slip measures.

•Keep the AP clean and dust-free.

•Do not place the AP in a moist area and avoid liquid intrusion.

•Keep the AP and installation tools away from walkways.

Temperature and humidity requirements

Table 1 Temperature and humidity requirements

Item Specification

Operating temperature 0°C to 45°C (32°F to 113°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Operating humidity 5% RH to 95%, noncondensing

Accessories provided with the AP

Figure 1 Accessories provided with the AP

Installation tools

When installing the AP, you might need the following tools. Prepare the installation tools as

required.

Figure 2 Installation tools

Installing the AP

Installation flowchart

Figure 3 Installation flowchart

Pre-installation tasks

Before installing an AP, perform the following tasks:

•Connect the AP to a power source and the network. Examine the LEDs to verify that the AP is

operating correctly. For information about AP LEDs, see "Appendix B Ports and LEDs."

•Cabling has been completed where the AP is to be installed.

•Record the MAC address and serial number of the AP for future use.

Determining the installation position

Determine the installation position by observing the following principles:

•Few obstacles such as wall exist between the AP and clients.

•The AP is far away from electronic devices (such as microwave oven) that may generate radio

frequency (RF) noise.

•The AP does not hinder people’s daily work and life.

•The place is not water seeping, water soaking, and condensing.

•The AP is more than 5 m (16.40 ft) away from 3G and 4G stations and antennas.

Installing the AP

The AP can be installed only indoors. You can mount the AP on a table or a wall.

Mounting the AP on a table

Figure 4 Mounting the AP on a table

Mounting the AP on a wall

1. Mark the installation holes on the wall.

Figure 5 Marking installation holes on the wall

56 mm

(2.20 in)

Indice

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente