HAMPTON BAY 705 114 Manuale utente
Cohutta
in Ceiling Fan
Owner’s Manual
Ventilador de Techo de m
Manual del Propietario
Cohutta
52
1,32
705 114
®
Cohutta by Hampton Bay
Cohutta
Ceiling Fan by Hampton Bay
Date Purchased
Store Purchased
ETL
Model No.
Serial No.
Vendor No.
UPC
Table of Contents
Safety Rules . . . . . . . . . . . . . . . . . . . . 1
Unpacking Y
our
Fan . . . . . . . . . . . . . . 2
Installing Y
our
Fan . . . . . . . . . . . . . . . 3
Installing the Light Kit. . . . . . . . . . . . . 8
Care of Y
our
Fan . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . 11
Warranty Information . . . . . . . . . . . . 12
222875
Thank you for purchasing our ceiling fan. This product has been
manufactured with the highest standards of safety and quality.
52
CF652KR-CHT
845952000216
Safety Rules - Read and Save These Instructions
WARNING
WARNING
ATTENTION
To reduce the risk of electric shock, insure electricity has been
turned off at the circuit breaker or fuse box before beginning.
All wiring must be in accordance with the National Electrical
Code “ANSI/NFPA 70-1999” and local electrical codes. Electrical
installation should be performed by a qualified licensed
electrician.
WARNING: To reduce the risk of electrical shock or fire, do not
use this fan with any solid-state fan speed control device. It will
permanently damage the electronic circuitry.
CAUTION: To reduce the risk of personal injury, use only the
screws provided with the outlet box.
The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 pounds. Use only
UL Listed outlet boxes marked “FOR FAN SUPPORT”.
The fan must be mounted with a minimum of 7 feet clearance from
the trailing edge of the blades to the floor.
Avoid placing objects in path of the blades.
To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
Do not use water or detergents when cleaning the fan or fan blades.
A dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
1.
2.
3.
4.
5.
6.
7.
8.
9.
After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and
ungrounded conductor on the other side of the outlet box.
All set screws must be checked and retightened where necessary
before installation.
10.
11.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN
INSTALLING THE BRACKETS, BALANCING THE BLADES OR
CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –
BETWEEN ROTATING FAN BLADES.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET
BOX.
FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE
DEPARTMENT OF ENERGY 2009 REGULATION. LAMPING THIS
PRODUCT OVER 190W WILL CAUSE THIS FAN TO NOT LIGHT.
PLEASE USE BULBS WITH A TOTAL WATTAGE UNDER THE 190W
REGULATION.
1
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:
9. Compartment cover (1)
10. Light fitter (1)
11. Small fan blades (3)
12. Receiver(1)
13. Transmitter (1)
13A. holder with 2 mounting screws Transmitter
14. Bulb(1)
1. Fan
2. Hanger bracket(1)
3. Canopy (1)
4. Canopy cover(1)
5. Downrod assembly (1)
6. Coupling cover(1)
7. Fan motor assembly(1)
8. Blade holders (3 )
blades (3) 15. Loose parts bag containing:
a. Blade hardware
(10 screws ( )and paper washers)6 mm
b. Small fan blade attachment hardware
c.
d.
attachment
Set of b hardware (1 screw) lade holders
Balancing kit (1)
(10 screws ( )and paper 13 mm washers)
3
6
4
5
1
2
8
10
7
9
11
12
ca
d
b
13
13A
14
2
WARNING
DO NOT INSTALL OR USE FAN
IF ANY PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-262-7511
Installing Your Fan
WARNING
Outlet Box
Outlet Box
Outlet Box
Figure 2
Figure 1
Ceiling
Mounting
Plate
Provide Strong
Support
Recessed
Outlet Box
Figure 3
Figure 4
Tools Required
Mounting Options
Phillips screwdriver, straight slot
screwdriver, step ladder and wire cutters.
If there isn't an existing UL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 35 lbs). Do
not use plastic outlet boxes.
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT FAN
ONLY TO AN OULET BOX MARKED ACCEPT-
ABLE FOR FAN SUPPORT AND USE THE
MOUNTING SCREWS PROVIDED WITH THE
OULET BOX. OUTLET BOX COMMONLY USED
FOR THE SUPPORT OF LIGHTING FIXTURE
MAY NOT BE ACCEPTABLE FOR FAN SUPPORT
AND MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Figures 1~3 are examples of different ways to
mount the outlet box.
Note: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling. The
maximum angle allowable is 18°. If the
canopy touches downrod, remove the
decorative canopy bottom cover and turn the
canopy 180° before attaching the canopy to
the mounting plate.
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at any Home Depot store).
3
Hanging the Fan
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
1.
2.
3.
4. Carefully feed fan wires up through the
downrod. (Figure 8) Thread the rod into the
coupling. Next, line up holes and replace lock
pin and hitch pin. Tighten set screws.
5. Slip coupling cover, canopy cover and
canopy onto downrod. (Figure 9) Carefully
reinstall hanger ball onto rod being sure that
cross pin is in correct position, set screws are
tighten and wires are not twisted.
Secure the hanger bracket to the ceiling
outlet box with the screws and washers
provided with your outlet box. (Figure 5)
from the motor
assembly.(Figure 6)
Loosen the two set screws
6. Now lift motor assembly into position and place
hanger ball into hanger bracket. Rotate until the
check groove
rotate if this is done correctly.
drops into the registration slot and
seats firmly. (Figure 10) Downrod should not
Figure 6
Downrod
Supply
wires
Figure 8 Figure 10
Registration
slot
Figure 5
Cross pin
Hanger
ball
Downrod
Figure 7
Outlet box
Hanger bracket
Hitch pin Lock pin
Set
screws
Motor Collar
Tighten
Screws
Firmly
Hitch Pin
Hanger ball
Ceiling
Canopy
Lock Pin
Coupling
cover
Canopy cover
Downrod
Lead Wires
Figure 9
4
Remove the hitch pin and lock pin
from downrod .Remove hanger ball from
downrod assembly by loosening set screw,
removing the cross pin,and sliding ball
off rod .
(Figure 7)
Figure 12
Receiver
Hanger
bracket
ON
Figure 11
Code switch
Rubber
cover
Making the Electrical
Connections
1. Insert the receiver into the hanger
bracket with the flat side of the receiver
facing the ceiling. (Figure 12)
2. Motor to Receiver Electrical Connections:
Connect the black wire from the fan to black
wire marked "TO MOTOR L".
Connect the white wire from the fan to
thewhite wire marked "TO MOTOR N" from
the receiver. Connect the blue wire from the
fan to the blue wire marked "For Light" from
the receiver. Secure the wire connections
with the plastic wire nuts provided. (Figure
13)
3. Receiver to House Supply Wires Electrical
Connections: Connect the black (hot) wire
from the ceiling to the black wire marked
“AC in L" from the receiver. Connect the
white (neutral) wire from the ceiling to the
white wire marked “AC in N" from the
4 . If your outlet box has a ground wire
(green or bare copper) connect it to the fan
ground wires and the hanger bracket ground
(Figure 13)
5
WARNING: To avoid possible electrical
shock, be sure electricity is turned off at
the main fuse box before wiring.
Receiver. Secure the wire connections
with plastic wire nuts provided.
(Figure 13)
wire. Secured the wire connection with a
plastic nut provided. After connecting the
wires spread them apart so that the green
and white wires are on one side of the
outlet box and black and blue wires are on
the other side. Carefully tuck the wire
connections up into the outlet box.
NOTE:
This remote control unit is equipped with
16 code combinations to prevent possible
interference from or to other remote units.
The frequency switches on your receiver
and transmitter have been preset at the
factory. Please recheck to make sure the
switches on transmitter and receiver are set
to the same position, any combination of
settings will operate the fan as long as the
transmitter and receiver are set to the same
position. (Figure 11)
MAKE SURE TAB AT BOTTOM OF HANGER
BRACKET IS PROPERLY SEATED IN GROOVE OF HANGER
BALL BEFORE
ATTACHING CANOPY TO BRACKET. FAILURE
TO PROPERLY SEAT TAB IN GROOVE COULD CAUSE
DAMAGE TO ELECTRICAL WIRING.
Figure 14
Outlet box
Hanger
bracket
Canopy
Screw
Canopy
cover
Lead Wires
Ball/Downrod
Assembly
Finishing the Installation
1. Tuck connections neatly into ceiling outlet box.
2. Remove one screw from the hanger bracket and loosen the other screw around
1/4″.
3. Align the canopy up to ceiling and over the loose screw. Place the canopy into
key hole and rotate canopy clockwise. (Figure 14)
4.Secure the canopy by use previous removed and loosened screw.
5. Place the canopy cover to the canopy and rotate canopy cover clockwise until
it is locked into right position.(Figure 14)
WARNING
SUPPLY CIRCUIT
Ground
Conductor
Outlet Box
Green
Ground
Lead
Ground to
Downrod
BLACK
WHITE
WHITE
WHITE
WHITE
BLACK
BLACK
BLACK
BLUE
BLUE
GREEN
ON
6
Figure 13
Attaching the Fan Blades
The following procedure should correct
most fan wobble. Check after each step.
1. Check that all blades and blade holder
screws are secure.
2. Most fan wobble problems are caused
when blade levels are unequal. Check this
level by selecting a point on the ceiling
above the tip of one of the blades. Measure
this distance as shown in Figure 18. Rotate
the fan until the next blade is positioned for
measurement. Repeat for each blade. The
distance should be equal within 1/8".
(Figure18)
If all blade levels are not equal, you can
adjust the blade level with the following
procedure.
3. Use the enclosed Blade Balancing Kit if
the blade wobble is still noticeable. Please
refer to the introduction provide in the
blade balancing kit, which is individual
packed.
4. If the blade wobble is still noticeable,
interchanging two adjacent (side
by side)
blades can redistribute the weight and
possibly result in smoother operation.
Touching
ceiling
Figure 18
Figure 17
Figure 16
7
1.Attach the fan blades to the blade holders
by using three screws ( the loose parts bag: a)
and paper washers as shown in Figure 15.
Start a screw into the blade holder, do not
tighten. Repeat for the 2 remaining screws
and washers.
2 .Tighten each screw securely starting with the
center screw. Make sure the blade is straight.
Repeat process for the other blades.
3.Remove the plastic blocks before installing
the blade holder to the fly wheel, discard the
plastic blocks but keep the screws. (Figure
16)
Tighten the blade assemblies onto fly
wheel by tightening two screws previously
removed from the fly wheel. Repeat process
for the other blade holders. (Figure 16)
5. Tighten a small fan blade to the fly wheel
with 3 blade screws (the loose parts bag: b )
provided. Repeat process for the other
blades.(Figure 17)
4.
Blade
holder Blade
Screws
Paper
Washer
Figure 15
Indice
Altri manuali HAMPTON BAY Fan
HAMPTON BAY
HAMPTON BAY WELLSTON 51360 Manuale utente
HAMPTON BAY
HAMPTON BAY ASHBURTON YG593-EB Manuale utente
HAMPTON BAY
HAMPTON BAY Veranda II Manuale utente
HAMPTON BAY
HAMPTON BAY Carriage House-2 138 108 Manuale utente
HAMPTON BAY
HAMPTON BAY STONERIDGE EF600K-52 Manuale utente
HAMPTON BAY
HAMPTON BAY SAUTERNE AL975-BN Manuale utente
HAMPTON BAY
HAMPTON BAY Capella AM113-BN Manuale utente
HAMPTON BAY
HAMPTON BAY PALM BEACH III 51499 Manuale utente
HAMPTON BAY
HAMPTON BAY Middleton 42 inch Manuale utente
HAMPTON BAY
HAMPTON BAY ALICANTE Manuale utente
HAMPTON BAY
HAMPTON BAY Northport 178-047 Manuale utente
HAMPTON BAY
HAMPTON BAY WELLSTON EF200B-44 Manuale utente
HAMPTON BAY
HAMPTON BAY NORTH POND 51716 Manuale utente
HAMPTON BAY
HAMPTON BAY Parker Ridge Manuale utente
HAMPTON BAY
HAMPTON BAY RIVERWALK Manuale utente
HAMPTON BAY
HAMPTON BAY BARROW ISLAND Manuale utente
HAMPTON BAY
HAMPTON BAY Fulton 140201 Manuale utente
HAMPTON BAY
HAMPTON BAY Andross Manuale utente
HAMPTON BAY
HAMPTON BAY SW18030 ORB Manuale utente
HAMPTON BAY
HAMPTON BAY Razor Manuale utente
