Hans Grohe AXOR ShowerSelect Round 36723 7 Series Manuale utente

INSTALLATION

ZH ⁄ 用户手册  ⁄  组装说明  02

EN ⁄ Instructions for use ⁄ Assembly instructions 04

Lesezeichen

中文  02

English 04

°C

AXOR ShowerSelect Square

36715X X7

AXOR ShowerSelect Soft Cube

36707XX7

°C

AXOR ShowerSelect Round

36723XX7

安全技巧

 装配时为避免挤压和切割受伤，必须戴上手套。

 本产品只允许作为洗浴、卫生和洁身之用。

 不得让儿童和肢体、精神和⁄或意识有障碍的成人

在不受监管的情况下使用淋浴系统。受酒精或毒

品影响的人员不得使用淋浴系统。

 冷热水管间过大的压力差必须予以平衡。

安装提示

⁄ 安装前必须检查产品是否受到运输损害。 安装后

将不认可运输损害或表面损伤。

⁄ 管道和阀门必须根据通用标准进行安装、冲洗和

检查。

⁄ 请遵守当地国家现行的安装规定。

⁄ 如果将恒温器或冷热水混合器调最大温度，闭锁

阀液压开口处可能造成烫伤。Hansgrohe 建议您设

置到“安全模式”。

技术参数

工作压强：  最大 1 MPa

推荐工作压强：  0,1 - 0,5 MPa

测试压强：  1,6 MPa

 (1 MPa = 10 bar = 147 PSI)

热水温度：  最大 60°C

热力消毒: 70°C ⁄ 4 分钟

⁄ 自动防止回流

⁄ 该产品专为饮用水设计！

符号说明

请勿使用含有乙酸的硅胶！

安全功能(参见第页 12 )

恒温阀芯的安全功能可以预先设定所希望的

最高出水温度，例如最高温度为42℃

调节(参见第页 12 )

安装完成后必须检查调温器的出水温度。如

在取水处测量所得的温度与调温器上设定的

温度有偏差，那么必须进行调整。

保养(参见第页 14)

⁄ 单向阀必须在符合国家或当地的法律的情

况下按照EN 806-5定期检查 (至少一年一

次) 。

⁄ 为了保证恒温器的稳定运转，请务必定期

从最热到最冷转动调温器。

大小(参见第页 17)

流量示意图(参见第页 17 )

  时的流速

 出水口 1

 出水口 2

备用零件(参见第页 20)

XX =  颜色代码 

00 =  镀铬 

34 = Brushed Black Chrome

67 = Matt Black

99 = Polished Gold-Optic

选装附件(参见第页 20)

  不在供货范围内

⁄ 加长 25 mm #13595000

⁄ 加长件22mm (墙壁不够深时) 97407XX0, 

#98860XX0, #98860XX0

⁄ 调平装置 1° #95521000

⁄ 螺母 + 法兰 #92696000

清洗(参见第页 18)

操作(参见第页 16)

03 ZH

安装(参见第页 06)

问题原因补救

 ⁄龙头出水量小 ⁄ 水压不足 ⁄ 检查总水压

⁄ 调压器过滤网脏污 ⁄ 清洁龙头前面和恒温阀芯的过滤

网。

⁄ 花洒滤网有垃圾堵塞 ⁄ 清洗花洒和软管间的过滤网

 ⁄串水，在龙头关闭的状态下，热水

被强迫流入冷水管路，或者相反。 ⁄ 单向阀有垃圾堵塞或漏水 ⁄ 清洗单向阀，如有必要则更换新的

 ⁄龙头出水温度和温度设定的不符 ⁄ 恒温阀芯未被调节 ⁄ 调节恒温器

⁄ 热水温度过低 ⁄ 将热水温度从42ºC升高到60ºC

 ⁄水温无法调节 ⁄ 恒温阀芯表面结垢 ⁄ 更换-恒温阀芯

⁄ 对于新的安装：基体连接不正确 (

可能是：右冷，左热) 或者安装时

旋转180º

⁄ 安装功能块时，旋转180º

 ⁄安全停止按钮不工作 ⁄ 弹簧损坏

⁄ 按钮僵化

⁄ 清洁弹簧和⁄或按钮，并视需要更换

 ⁄阀门不灵活 ⁄ Select 停止阀 DN9 件损坏 ⁄ 更换 Select 停止阀 DN9

 ⁄花洒或龙头出水嘴滴水 ⁄ Select 停止阀 DN9 件损坏 ⁄ 更换 Select 停止阀 DN9

 ⁄无法按下按键或按键不起作用 ⁄ 锁止阀保险装置未移除 ⁄ 移除锁止阀保险装置

 ⁄按键卡住，难以正常使用 ⁄ 不再润滑密封件 ⁄ 润滑密封件

 ⁄确保按键未处于按下状态 ⁄ 正确截短调节转接器 ⁄ 按照图 7 截短并安装调节转接器 

(参见第页 07 + 10 )

⁄ 将按键完全卡入装饰花，然后装上

装饰花

SAFETY NOTES

Gloves should be worn during installation to prevent

crushing and cutting injuries.

The product may only be used for bathing, hygienic

and body cleaning purposes.

Children as well as adults with physical, mental and⁄or

sensoric impairments must not use this product without

proper supervision. Persons under the inﬂuence of

alcohol or drugs are prohibited from using this product.

The hot and cold supplies must be of equal pressures.

INSTALLATION INSTRUCTIONS

⁄ Prior to installation, inspect the product for transport

damages. After it has been installed, no transport or

surface damage will be honoured.

⁄ The pipes and the ﬁxture must be installed, ﬂushed and

tested as per the applicable standards.

⁄ The plumbing codes applicable in the respective

countries must be observed.

⁄ If the thermostat or mixer is set to maximum water

temperature, there is a risk of scalding at hydraulical

opening of the check valve. For this reason, Hansgrohe

recommends that you set up the "Safety Function".

TECHNICAL DATA

Operating pressure: max. 1 MPa

Recommended operating pressure: 0,1 - 0,5 MPa

Test pressure: 1,6 MPa

(1 MPa = 10 bar = 147 PSI)

Hot water temperature: max. 60°C

Thermal disinfection: 70°C ⁄ 4 min

⁄ Safety against backﬂow

⁄ The product is exclusively designed for drinking water!

SYMBOL DESCRIPTION

Do not use silicone containing acetic acid!

SAFETY FUNCTION (see page 12 )

The desired maximum temperature for example

max. 42º C can be pre-set thanks to the safety

function.

ADJUSTMENT (see page 12)

After the installation, the output temperature of

the thermostat must be checked. A correction is

necessary if the temperature measured at the

output diﬀers from the temperature set on the

thermostat.

MAINTENANCE (see page 14 )

⁄ The check valves must be checked regularly

according to EN 806-5 in accordance with

national or regional regulations (at least once

a year).

⁄ To guarantee the smooth running of the

thermostat, it is necessary from time to time to

turn the thermostat from total hot to total cold.

DIMENSIONS (see page 17)

FLOW DIAGRAM (see page 17)

free ﬂow

 Outlet 1

 Outlet 2

SPARE PARTS (see page 20 )

XX = Colors

00 = Chrome Plated

34 = Brushed Black Chrome

67 = Matt Black

99 = Polished Gold-Optic

SPECIAL ACCESSORIES

(see page 20 )

order as an extra

⁄ extension 25 mm #13595000

⁄ Extension Set 22 mm (when wall is not deep

enough) 97407XX0, #98860XX0,

#13596XX0

⁄ levelling set 1° #95521000

⁄ nut + ﬂange #92696000

CLEANING (see page 18 )

OPERATION (see page 16 )

05 EN

ASSEMBLY (see page 06 )

FAULT CAUSE REMEDY

⁄ Insuﬃcient water ⁄ Supply pressure inadequate ⁄ Check water pressure (If a pump has

been installed check to see if the pump

is working).

⁄ Regulator ﬁlter dirty ⁄ Clean ﬁlter in front of the mixer and on

the MTC-thermo cartridge

⁄ Shower ﬁlter seal dirty ⁄ Clean ﬁlter seal between shower and

hose

⁄ Crossﬂow, hot water being forced into

cold water pipe, or vice versa, when

mixer is closed

⁄ Backﬂow preventers dirty or leaking ⁄ Clean backﬂow preventers, exchange

if necessary

⁄ Spout temperature does not

correspond with temperature set

⁄ Thermostat has not been adjusted ⁄ Adjust thermostat

⁄ Hot water temperature too low ⁄ Increase hot water temperature to

42 ºC to 60 ºC

⁄ Temperature regulation not possible ⁄ thermo cartridge calciﬁed ⁄ Exchange thermo cartridge

⁄ For new installations: basic body incor-

rectly connected (should be: cold right,

hot left) or installed with 180º rotation

⁄ Install function block turned through

180º

⁄ Safety stop button not operating ⁄ Spring defective

⁄ Button calciﬁed

⁄ Clean spring and ⁄or button, exchange

if necessary

⁄ Valve stiﬀ ⁄ Select stop valve DN9 damaged ⁄ Exchange Select stop valve DN9

⁄ Shower or spout dripping ⁄ Select stop valve DN9 damaged ⁄ Exchange Select stop valve DN9

⁄ Pushbutton cannot be actuated or is

without function

⁄ Safety guard of isolating valve has not

been removed

⁄ Remove safety guard from isolating

valve

⁄ Pushbutton is jammed or stiﬀ ⁄ Seal needs greasing ⁄ Grease the seal

⁄ Pushbutton does not snap in ⁄ Select Adapter incorrectly trimmed ⁄ Trim and mount Select Adapter accord-

ing to Fig. 7 (see page 07 + 10 )

⁄ First, fully press the pushbutton down

into the rosette; then, mount the rosette

SW 4 mm

(5 Nm)

Armaturenfett

Grease

䀵滑油

01700187

1 2

3 4

5 6

SW 5 mm

1 - 2 mm

Montage

SW 4 mm

0 mm

> 0 mm

910

Montage Sicherung

X + 11

1 - 2 mm

(0,1 Nm)

SW 10 mm

(2 Nm)

11 12

13 14

15 16

Montage

°C

17 18

19 20

21 22

Montage

0 mm

< 0 mm

°C

CLICK

23 24

°C

A B

SW 3 mm

(1 Nm)

°C

D E

CLICK

Montage Select-Adapter kürzen 2

Questo manuale è adatto per i seguenti modelli

Altri manuali Hans Grohe Prodotto idraulico

Hans Grohe

Hans Grohe AXOR Urquiola 11732000 Manuale

Hans Grohe

Hans Grohe 94139 7 Series Manuale utente

Hans Grohe

Hans Grohe Talis N 220 U-Style 1-Spray 72806 1 Series Manuale di istruzioni

Hans Grohe

Hans Grohe Axor Starck 10402001 Guida all'installazione

Hans Grohe

Hans Grohe Metris S 31161000 Manuale

Hans Grohe

Hans Grohe Ecostat E 15705000 Manuale

Hans Grohe

Hans Grohe FixFit Porter E Series Manuale

Hans Grohe

Hans Grohe Talis E2 31635000 Manuale utente

Hans Grohe

Hans Grohe Secuflex 28380 1 Series Manuale di istruzioni

Hans Grohe

Hans Grohe AXOR Starck X 10205000 Manuale

Hans Grohe

Hans Grohe Metris E 31083 1 Series Manuale di istruzioni

Hans Grohe

Hans Grohe Ecostat S 15757 Series Manuale

Hans Grohe

Hans Grohe 13620180 Manuale utente

Hans Grohe

Hans Grohe Logis 110 Fine 71251 Series Manuale

Hans Grohe

Hans Grohe Mediano 14907000 Manuale utente

Hans Grohe

Hans Grohe Rainfinity 250 1jet EcoSmart 26229 Series Manuale

Hans Grohe

Hans Grohe E 04226**0 Manuale di istruzioni

Hans Grohe

Hans Grohe iBox universal 01850180 Manuale utente

Hans Grohe

Hans Grohe Unica'S 27 727 000 Manuale utente

Hans Grohe

Hans Grohe AXOR ShowerHeaven 720 10625800 Manuale utente

Hans Grohe

Hans Grohe Talis S 32841 Series Manuale

Hans Grohe

Hans Grohe Axor Uno 13453 Series Manuale utente

Hans Grohe

Hans Grohe Ecostat 1001 13240 Series Manuale utente

Hans Grohe

Hans Grohe AXOR Bouroullec 19418000 Manuale

Manuali Prodotto idraulico popolari di altre marche

Weka

Weka 506.2020.00E Istruzioni operative

Kohler

Kohler K-6228 Istruzioni per il montaggio

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manuale utente

American Standard

American Standard DetectLink 6072121 Manuale utente

Uponor

Uponor Contec TS Manuale utente

Pfister

Pfister Selia 49-SL Manuale utente

Fortis

Fortis VITRINA 6068700 Manuale utente

Fortis

Fortis MILANO 78211JS Manuale utente

Kohler

Kohler K-12183 Istruzioni per il montaggio

Maxxus

Maxxus MX-M206-01 Manuale utente

Moen

Moen 5922 Series Manuale utente

Viega

Viega Prevista Pure 8512 Manuale utente

Kohler

Kohler Centerset K-15240 Istruzioni per il montaggio

Viega

Viega Prevista Dry 8522.33 Manuale utente

Sanela

Sanela Lema SLP 59RB Manuale utente

Elkay

Elkay EDF15AC Manuale di installazione

baliv

baliv WT-140 Manuale utente

Kohler

Kohler Mira Eco Manuale operativo