Heatstore HS2000X Manuale utente
HS2000X Downflow Heater
Installation and Operating Instructions
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
HS2000X(R)instructions 15/8/14 10:33 Page 1
Safety Warnings
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children SHALL NOT play with the appliance.
Cleaning and user maintenance SHALL NOT be made
by children without supervision.
Children of less than 3 years old should be kept away
unless continuously supervised.
Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided that it
has been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8
years shall not plug in, regulate and clean the
appliance or perform user maintenance.
CAUTION: Some parts of this product can become
very hot and cause burns. Particular attention has to
be given where children and vulnerable people are
present.
This appliance should be installed by a competent and
qualified electrician in accordance to the IEE
regulations.
The HS2000X Downflow Heater provides an instant heat
source for kitchens and bathrooms and is styled to match
our shower range.
2
HS2000X(R)instructions 15/8/14 10:33 Page 2
DO NOT operate the appliance with a damaged cord.
DO NOT use this heater in dusty environments or
where flammable vapours are present(e.g. in a
workshop or garage).
DO NOT cover the heater. DO NOT allow the heater
to come into contact with flammable material for
example curtains or furniture.
Disconnect this heater before any repairs, cleaning or
maintenance is carried out upon it.
This heater should not be located directly below a
power socket.
DO NOT operate this appliance if the front cover is
not correctly positioned on the unit.
DO NOT use this heater in the immediate
surroundings of a bath, a shower or a swimming pool.
This appliance is not intended for use by persons
(including children) with reduced physical, sensorary
or mental capabilities, or lack of experience and
knowledge unless they have been given supervision or
instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
WARNING: the cable outlet must be controlled by a
double pole switch with a contact separation of at
least 3mm in all poles. When located within a
bathroom the switch must be a pullcord; if located
outside the bathroom it should be adjacent to the
entrance. The appliance must be located in a position
that does not allow any person to touch it whilst they
are in the bath or shower.
3
HS2000X(R)instructions 15/8/14 10:33 Page 3
Installation: THE APPLIANCE IS DESIGNED ONLY FOR WALL MOUNTING.
Choose position carefully for mounting the appliance, enough
space must be left around appliance. NOTE: It is NOT permissible to
install this heater in Zones 1 or 2. Please install it outside Zone 2 in the
undesignated area – see Figure 1 above.
The heater must be mounted at a high level – see opposite.
Loosen the two screws at the top of the front of the heater and lift off
the front cover.
Drill two 8mm holes on the wall at a distance of 190mm on a
horizontal line, another one at a distance of 115mm down from the
horizontal line.
Insert the three plastic plugs into the three holes, and then screw two of
the screws provided into the lower holes. Do not screw these two screws
fully home as the heater will hang on them later. As a guide they need
to be left protruding by about 3mm
Hang the heater on the two screws. It may be necessary to mount and
dismount the heater a few times, slightly tightening and/or loosening
the screws as required, to ensure a snug fit.
0.6 m
RCD-protected
sockets now
allowed beyond
3m from Zone 1
Figure 1
RCD protected
sockets now
allowed beyond
3m from Zone 1
4
HS2000X(R)instructions 15/8/14 10:33 Page 4
Use the wall bracket to secure the heater by fitting the last screw into
the upper hole.
Remove the fixing board from inside the heater.
Thread the supply cable through the hole in the rear of the case.
Make connections to the supply terminals according to the colour code
(Please see Electrical Connection). Ensure that there are no strands or
whiskers protruding from the terminals
Secure the cable under the fixing board, ensure that the cable is griped
firmly but take care not to over tighten the screws.
Select the desired mode of operation using the switch i.e. I= 1kW fixed
heat, II=1kW fixed heat + 1kW variable thermostat controlled set the
thermostat to the mid position. Close and secure the front cover.
Restore the power and switch on.
Adjustment
The adjustment of the internal thermostat must be carried out by a
competent person.
Switch off the main power and remove the fuse from the double pole
fused spur.
Remove the two screws on the front of the case and remove the front
cover.
Select the desired mode of operation using the switch i.e. I= 1kW fixed
heat, II=1kW fixed heat+ 1kW variable thermostat controlled
Turn the thermostat control clockwise to increase the room temperature
and anti-clockwise to decrease.
Close the front over and secure using the two screws, replace the fuse
and switch on the power supply.
A
C
BB
MMiinniimmuummmmoouunnttiinnggddiissttaanncceess
AA––228800mmmmminimum of space required above the heater
BB––225500mmmmminimum space on either side of the heater
CC––11880000mmmmminimum height from the floor
5
HS2000X(R)instructions 15/8/14 10:33 Page 5
Electrical Connection
Connect the electrical wires of this appliance to a fused spur according to
the following colour code – Blue: Neutral, Brown: Live – in accordance
with NECEIC wiring regulations, with a minimum cable size of 1mm2.
NB. If no fused spur is nearby consult a suitably qualified electrician.
Safety Control (Thermal Cut-Out)
This model has two levels of over heat protection.
THERMAL CUT OUT: This product is fitted with a thermal cut out which in
the event that it malfunctions or overheats, the thermal cut out switches the
heater off automatically. when this happens the heater will reset itself once
the temperature has reduced sufficiently.
THERMAL FUSE: This thermal fuse is added as an additional safety
feature, this is a non-resettable switch which will require the unit to be
returned to the supplier for replacement.
The most common cause of overheating is deposits of dust or fluff entering
the heater. Ensure these deposits are removed regularly by electrically
isolating the unit and vacuum cleaning the air vents and front grille.
The Controls
The in-built cut out on this appliance is a safety device which switches the
heater off, if the operating temperature gets to hot.
The thermal fuse is an additional safety feature to cut out.
The pull cord on the appliance operates the ON/OFF switch (an indicator
light illuminates when the appliance is on).
The heater has an internal thermostat which should be set during
installation.
The thermostat has 3 different settings : 1 = Low, 2 = Med, 3 = High.
Care and Cleaning
The electric heater should be cleaned regularly.
Disconnect electricity supply and allow heater to cool, wipe surface clean
with a soft damp cloth. Do not use detergent or abrasives.
Do not scrape the surfaces with sharp hard tools.
6
HS2000X(R)instructions 15/8/14 10:33 Page 6
7
HS2000X(R)instructions 15/8/14 10:33 Page 7
Issue 4 0814
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
SPECIFICATION: HS2000X
RATING:240V/2000W, 230V/1900W, ~50Hz;
;
DIMENSIONS:237w x 244.5h x 130d mm;
ONE YEAR
IP
21
ZONE
U
Telephone: 0117 923 5375 Fax: 0117 923 5374
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
HS2000X(R)instructions 15/8/14 10:33 Page 1
Indice
Altri manuali Heatstore Stufa
Heatstore
Heatstore HSCVDURF Manuale d'uso e manutenzione
Heatstore
Heatstore HSRCH4500RF Manuale utente
Heatstore
Heatstore Dynamic InteliPlinth HSDBU24 Manuale utente
Heatstore
Heatstore HSQH3000 Manuale utente
Heatstore
Heatstore HSFAH30 Manuale utente
Heatstore
Heatstore HSAC9000CX Manuale
Heatstore
Heatstore HSACR X Series Manuale utente
Heatstore
Heatstore HSACW9000 Manuale
Heatstore
Heatstore HSCF3000E Manuale d'uso e manutenzione
Heatstore
Heatstore HS4212XNi Manuale utente
Heatstore
Heatstore DYNAMIC HSDR500T Istruzioni operative
Heatstore
Heatstore HSCPF3000 Manuale
Heatstore
Heatstore HS2020XCN Manuale utente
Heatstore
Heatstore HSOFR1500TX Manuale utente
Heatstore
Heatstore HS1500C Manuale utente
Heatstore
Heatstore HSDI330 Manuale di istruzioni
Heatstore
Heatstore HSXCA12X Manuale utente
Heatstore
Heatstore HSAC9000E Manuale utente
Heatstore
Heatstore HS2020TXN Manuale utente
Heatstore
Heatstore HSDS Manuale utente
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente