Heatstore HSPBRF Manuale utente

INDEX Section

General information ------------------------------------------------------------ 1

Dimensions ---------------------------------------------------------------------- 2

Installation Details -------------------------------------------------------------- 3

Electrical Connections -------------------------------------------------------- 4

Operation ------------------------------------------------------------------------- 5

Servicing & Maintenance ----------------------------------------------------- 6

SURFACE WARM CEILING HEATERS

MODELS

HSSCH3000RF, HSSCH4500RF

INSTALLATION AND OPERATING MANUAL

HSPBRF HSTIRF HSVTRF

1.1 Introduction

This instruction manual describes the Heatstore

Surface Warm Air Ceiling Heaters.

The heater is designed to be suspended from the

ceiling.

1.2 General

All installations must be in accordance with the

regulations in force in the country of use.

These instructions must be handed to the user on

completion of the installation.

Installers and service engineers must be able to

demonstrate competence and be suitably

qualified in accordance with the regulations in

force in the country of use.

To ensure continued and safe operation it is

recommended that the appliance is serviced

annually.

The heater outlet / inlet must not be obstructed

during use.

1.3 Electrical Supply

Electrical supply is 230/240V single phase,

Neutral and Earth. The maximum cable inlet size is

4mm².

It is recommended that the electrical supply to the

base unit in the heater is via an appropriate

switched isolator in accordance with the

regulations in force in the country of use and must

be via a fused isolator having a contact separation

of greater than 3mm on all poles.

BMS control, time switches, room thermostats and

door interlocks can be installed at the discretion

and responsibility of the installer.

All units must be wired in accordance with I.E.E

regulations for the Electrical Equipment of

Buildings and the installer should ensure that a

suitable isolating switch is connected in the mains

supply.

1.4 Controller RF models

The HSSCH3000RF and HSSCH4500RF will only

operate when paired and controlled by the RF

range of wireless controllers shown above.

1.6 Location

All units should be installed horizontally. It is

recommended that the ceiling heater is

suspended using four 10mm rods.

Care must be taken to allow complete free air

movement into the inlet grilles of the unit to

ensure the correct working operation of the

heater. If the HSSCH3000RF and the HSSCH4500RF

heaters are mounted close to the wall or corner

the discharge opening should be facing the

wall. The minimum distance from the wall.

1.7 Clearance distances

It is acceptable for the heater to sit flush to the

ceiling.

The minimum mounting height (floor to grille) is

2.2m for the HSSCH3000RF and the HSSCH4500RF

The recommended mounting height is 2.5m for

the HSSCH3000RF and the HSSCH4500RF

Heatstore RF Wireless Controllers

HSPBRF HSTIRF

HSVTRF

. General Information

SUSPENSION POINTS

1.8 Clearance distances

1.9 Health and Safety

Sole liability rests with the installer to ensure that all

site safety procedures are adhered to during installa-

tion.

Sole liability rests with the installer to ensure that

protective safety wear such as hand, eye, ear and

head protection is used during installation of the

product.

Do not rest anything especially ladders against the

product.

1.10 Standards

Units conform to the European electrical standard

BS EN 60335-2-30

HSSCH3000RF, HSSCH4500RF

. General Information

2. Dimensions

ENSURE THE AIR OUTLET OF HSSCH3000RF

AND HSSCH4500RF IS NEAREST TO THE WALL

OR CORNER.

3.1 Installation

It is the sole responsibility of the installer to en-

sure that the points of attachment to the building

are sound. Care must be taken to allow complete

free air movement into the inlet grilles of the unit to

ensure the correct working operation of the heater.

Carefully unpack the unit. The unit is supplied with

a length of self-adhesive foam strip. This can be

cut into lengths and is to be laid on the 4 sides of

the bottom of the heater casing . This will ensure

that the unit assembly is free from vibration.

The weight of the HSSCH3000RF, HSSCH4500RF

is 12kg

-Split and remove shroud

A pair of machine screws hold each shroud half

together at each joint. A machine screw secures

each shroud half to each appliance beam. Re-

move these machine screws and slide each

shroud half off the appliance base panel. The

base panel fits inside the shroud halves.

The diffuser is already clipped into and under the

base panel and need not be removed.

- Hanging Rod Positions

With the shroud removed the two appli-

ance beams reveal the holes/slots

shown and dimensioned below. It is

required that two 10 mm hanging rods

(stud bars) support each appliance

beam. The rods pass through and into

each appliance beam. Support washers

together with nuts locate and lock the

appliance beams after adjustment to

level the appliance.

- Replace Shroud Halves

The reverse of above. Slide shrouds

beneath and around base panel. Se-

cure each shroud half to each appliance

beam with machine screws. Screw

shroud halves together at each joint.

4.1 Electrical Connections.

These units are suitable for connection to a

230/240 Volt 50 Hz single phase supply.

The appliance shall be connected to the supply via

an appropriate switched fused double pole isolator

having a contact separation of greater than 3mm.

Test for correct operation and refit the cover.

Fig.1 Air discharge of HSSCH3000RF

and HSSCH4500RF

For connection to the mains supply it will be

necessary to open the terminal cover at the side/

back of the unit to connect the supply from the

controls prior to refitting the cover. Wire in accord-

ance to the wiring diagrams.

For safety reasons, a sound earth connection

must always be made to the unit before it is put to

use. The unit should be wired in accordance with

IEE Regulations for the Electrical Equipment of

Buildings.

Fig.3 Heater assembly

SUSPENSION POINTS

TERMINAL COVER

TOP OR SIDE CABLE ENTRY

3. Installation Details

4. Electrical Connections

5.1 RF Controllers

The heaters HSSCH3000RF and HSSCH4500RF can be controlled by any Heatstore RF wireless

controller. Each RF controller can control any number of heaters providing they are in he RF range.

For more details please follow the instructions supplied with the controller.

4.2 Electrical connections

Fig.8 Heater with terminal cover open Fig.9 Terminal cover detail

Heatstore RF Wireless Controllers

HSPBRF HSTIRF HSVTRF

4. Electrical Connections

5. Operation

ALWAYS ENSURE THAT THE MAIN

EXTERNAL ELECTRICITY SUPPLY IS

SWITCHED OFF BEFORE COMMENCING ANY

MAINTENANCE ON THIS HEATER.

To obtain the best results from the heater, it is

essential to avoid the accumulation of dust and

dirt within the unit on the air inlet and discharge

grilles. For this reason regular cleaning is

necessary.

Cleaning of the fan is best carried out with a soft

brush.

The product should be serviced annually.

Servicing shall be undertaken by a competent

person.

6.2 General

If the heater does not operate a competent service

engineer should be called to identify the nature of

the fault.

All heaters are fitted with motor thermal protection.

Other faults in relation to the element, motor and

wiring should be identified using conventional fault

finding techniques.

In the event that electrical components are

replaced, please ensure that electrical safety

checks in accordance with the regulations in force

in the country of use are undertaken.

6.3 Thermal cut-out

The units are protected from overheating in the

event of fan failure or an obstruction of the free

airflow, by thermal cut outs. If this happens the

thermal cut outs switch off the appliance. The ap-

pliance will not operate until the heater is discon-

nected from the mains supply and it has cooled

down.

If this fault re-occurs again, refer to the section

‘6.4 fault finding’.

6.1 Maintenance 6.4 Fault Finding

If the heater will not operate, disconnect it from

the mains and arrange for a certified electrician to

attend and investigate the reason.

6.5 Replacing the Fan Heater

a) Split and remove shroud

b) Remove the grille.

c) Disconnect the internal wiring from the blower

d) Remove the four screws fixing the fan heater

assembly to the back of the case.

e) The fan heater assembly can now be eased

forward and removed from the heater case.

f) Fit replacement fan heater and reassemble in

reverse order.

6.6 Spares

It is essential when ordering spares or replace-

ment parts to state the model number and the

serial number on the rating label fixed to the side

of the unit below the terminal cover.

In the interest of progress the Company reserve

the right to vary specifications from time to time

without notice. The material listed is offered sub-

ject to the Company’s General Conditions of Sale,

a copy of which can be obtained on request.

6. Servicing & Maintenance

Heatstore

Unit 12, Access 18,

Bristol BS11 8HT

Tel: 0117 9235 375

Fax: 0117 9235 374

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Heatstore Stufa

Heatstore

Heatstore HSXCA12X Manuale utente

Heatstore

Heatstore HS2000T Manuale utente

Heatstore

Heatstore HSAC9000E Manuale utente

Heatstore

Heatstore HSCPF3000 Manuale

Heatstore

Heatstore Dynamic InteliPlinth HSDBU24 Manuale utente

Heatstore

Heatstore HS2000X Manuale utente

Heatstore

Heatstore HSACR3000N Manuale

Heatstore

Heatstore HSFAH30 Manuale utente

Heatstore

Heatstore HSCF3000E Manuale d'uso e manutenzione

Heatstore

Heatstore HS2020TXN Manuale utente

Heatstore

Heatstore HSACR X Series Manuale utente

Heatstore

Heatstore DYNAMIC HSDR500T Istruzioni operative

Heatstore

Heatstore HSQH3000 Manuale utente

Heatstore

Heatstore HSCFH60WX Manuale utente

Heatstore

Heatstore HSQH2000 Manuale utente

Heatstore

Heatstore HSCEH7115N Manuale

Heatstore

Heatstore HSRCH4500RF Manuale utente

Heatstore

Heatstore HS2020XCN Manuale utente

Heatstore

Heatstore HSP500WRF Manuale d'uso e manutenzione

Heatstore

Heatstore HSDHHR050 Manuale utente

Heatstore

Heatstore HS1500C Manuale utente

Heatstore

Heatstore HSAC3000X Manuale

Heatstore

Heatstore HSAC6000X Manuale

Heatstore

Heatstore HSP500SSE Manuale d'uso e manutenzione

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente