Hickok AUTO WAVE II Manuale utente
USER GUIDE
Safety Information
Before using this equipment, carefully read, understand and follow instructions and safety messages
on equipment and in this guide.
This guide cannot anticipate or provide advice and cautions for all situations encountered by
technicians. With this in mind, always follow and refer to the manuals provided by the manufacturer
of the vehicle or equipment being tested or used for all information and testing procedures whenever
diagnosing, repairing or operating such vehicle or equipment.
Failure to follow the instructions, cautions and warnings provided here as well as those provided by the
vehicle and equipment manufacturers can result in re, explosion, bodily injury and property damage.
In addition to the information listed below, additional warnings and cautions are listed throughout the
guide. Please read them carefully.
Fuel vapors are toxic and explosive, which can cause severe injury or death.
• Use proper ventilation to avoid breathing fuel vapors.
• Minimize contact with the skin with the use of gloves (such as nitrile gloves) when there is
possibility of getting methanol fuel on your hands.
• If the skin is directly exposed, wash the area immediately and change any clothes that have
become wet with fuel.
• Always wear approved safety glasses when testing. Should fuel get into eyes, ush eyes
immediately with water and consult your physician.
Vehicles emit ammable vapors which can ignite.
• Keep ames, sparks, cigarettes and other ignition sources away from the vehicle at all times.
• In case of re, never use water to ght ames caused by methanol or methanol blended gasoline.
This will cause the ames to spread instead of extinguishing them.
• Use a dry chemical extinguisher to ght ames (preferably one marked ABC, though BC is
acceptable). A foam extinguisher is acceptable only if it is ARF grade, which is resistant to alcohol.
Before beginning any tests, make sure the test environment is safe and the vehicle meets these conditions:
• Test area should be well ventilated.
• Vehicle should be in park.
• Wheels should be blocked.
• Engine should be at normal operating temperature.
• Vehicle should have normal exhaust ow.
• Keep all tester cables clear of exhaust manifolds and radiator fan blades.
• Use caution when testing on a vehicle while the engine is running (surfaces may become hot,
electric cooling fans may turn on unexpectedly, etc.)
© 2017 Hickok Inc. All rights reserved.
All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, without written permission from Hickok.
Hickok assumes no responsibility for use of this equipment by untrained or unauthorized persons.
Printed in the United States of America.
3
Contents
Components.....................................................................................5
Auto Wave II ................................................................................................................................................ 6
Red Test Leads............................................................................................................................................. 6
Black Test Lead............................................................................................................................................ 6
USB Cable ..................................................................................................................................................... 6
Flexible Back Probe Pins.......................................................................................................................... 6
Lantern Tip Test Probes............................................................................................................................6
Alligator Clips.............................................................................................................................................. 6
Controls and Connections...............................................................7
Front View .........................................................................................................................7
On-O / Menu Button.............................................................................................................................. 7
Help / Channel Button.............................................................................................................................7
Select Button............................................................................................................................................... 8
Navigation Buttons................................................................................................................................... 8
Back View...........................................................................................................................9
LCD Screen Symbols and Indicators..................................................................... 10
Setup Procedure ............................................................................11
For One Channel Use ................................................................................................. 11
For Two Channel Use.................................................................................................. 11
Why Ground Hookup Is Important ....................................................................... 12
How To… ........................................................................................13
View a Live Waveform................................................................................................ 13
Zoom or Pan While Viewing Live or Saved Waveform.................................... 13
Capture and Save a
Waveform .......................................................................................................13
Create Bitmaps ............................................................................................................. 14
View Saved
Waveforms................................................................................................. 14
Replace the
B
a
tt
er
y...............................................................................................................16
Main Menu Functions....................................................................17
Main Menu..................................................................................................................... 17
Auto-Set.......................................................................................................................... 17
4
Contents
Volt Meter....................................................................................................................... 18
File List............................................................................................................................. 18
Browse Waves ............................................................................................................... 19
Battery Status................................................................................................................ 19
Delayed Capture.......................................................................................................... 19
USB File Access............................................................................................................. 20
Voltage Range .............................................................................................................. 20
Trigger Mode................................................................................................................. 20
Trigger Using................................................................................................................. 20
Trigger Level.................................................................................................................. 21
Coupling ......................................................................................................................... 21
Example Waveforms......................................................................22
Accessories.....................................................................................23
75300 Secondary Ignition Pickup.......................................................................... 23
77300 Flex Probe Combo Kit................................................................................... 23
Technical Information ...................................................................24
Time Scales ................................................................................................................... 24
Time Scales and Associated Sampling Characteristics .................................. 24
Voltage Scales .............................................................................................................. 25
Specications.................................................................................26
Contact Information......................................................................27
Warranty.........................................................................................28
5
Components
MENU CHNL
?
Test Lead
Test Lead
Test Lead
USB Cable
Auto Wave II
Alligator Clips
Flexible Back Probe Pins
Lantern Tip Test Probes
6
Components
Auto Wave II
Use along with the supplied test leads and accessories. Allows you to view single
or dual waveforms.
Red Test Leads
Two 5ft right angle/straight shielded banana plug test leads for viewing single or
dual waveforms.
Black Test Lead
One 5ft right angle/straight shielded banana plug test lead for ground.
Note: A good ground connection is required for obtaining clean waveforms.
USB Cable
One 3ft standard A male to mini-B USB cable. Cable is used to download Large
and Small saved BMP waveform images for viewing on a PC.
Flexible Back Probe Pins
Two red female shielded exible slip on back probe pins.
Lantern Tip Test Probes
Two red male banana plug tip test probes. Attach female banana plug test
accessories to the tips or use as standard test probes.
Alligator Clips
Two red and one black female banana plug slip on alligator clips.
7
Controls and ConnectionsControls and Connections
Front View
On-O / Menu Button
To power on Auto Wave II — press and release the On-O / Menu button.
To access the Main Menu — press and release the On-O / Menu button with the
unit on.
• Press and release the Menu button again to return.
To power o Auto Wave II — press and hold the On-O / Menu button.
• Auto Wave II automatically turns off after 2-minutes of no activity.
Help / Channel Button
To display help on the current operation — press and release the Help /Channel
button at any time.
• Continue to press and release the Help button to scroll through the
pages (if there is more than one) and to return to the current operation.
To toggle between channel CH-1 and CH-2 for adjustments when viewing dual
waves—press and release the Help / Channel button.
MENU CHNL
?
Help/ Channel
On-O / Menu
Navigation Buttons (up, down, left, right)
LCD Screen
Select Button
8
Controls and Connections
Select Button
The function of this button varies depending on use and the mode of operation
you are currently in.
Press and release to:
•Select Main Menu items.
• Toggle between Zoom and Pan modes.
Press and hold to:
• Capture and save the currently displayed wave.
• Display a list of options (Resume, Bitmap, Cancel, Delete) while viewing
saved waveforms.
Navigation Buttons
The function of this button varies depending on the mode of operation you are
currently in.
Up, Down, Left, Right buttons are used to:
• Navigate Main Menu items.
• Adjust time and voltage scales when viewing live or saved
waveforms (ZOOM).
• Move waveform left, right, up or down when viewing live or saved
waveforms (PAN).
• Toggle through File List and Browse Waves menu items.
• Clear Min / Max values in Voltmeter mode.
• Select Voltage Ranges, Trigger Mode, Trigger Using, Trigger Level and
Coupling modes.
See Main Menu and How To sections for more detail
9
Controls and Connections
CH 2 CH 1GND
www.hickokwaekon.com
Input Jacks
CH-2, GND, & CH-1
Mini USB Port9V Battery Compartment
Hanger / Stand
Back View
(Right Side View)
10
Controls and Connections
LCD Screen Symbols and Indicators
ZOOM
CH-1
T=2 mS
V1= 2V
V2= 1V
Active PAN /
ZOOM
Time Divisions
(yellow)
Trigger
Indicator
Voltage
Divisions
(red)
Zero Voltage
Lines (gray)
Time Scale
(Yellow) Channel 1
Voltage Scale
(green)
Channel Channel 2
Voltage Scale
(purple)
Indice
Altri manuali Hickok Apparecchiature di prova
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
