HIK VISION DS-2CE17U8T-IT Manuale utente
UM DS-2CE1xU8T-ITx 042618NA 1
• DS-2CE17U8T-IT
• DS-2CE18U8T-IT3
TurboHD
4K Series Bullet Camera
User Manual
Thank you for urchasing our roduct. If there are
any questions or requests, do not hesitate to contact
the dealer.
This manual a lies to the models below:
This manual may contain technical incorrect laces or
rinting errors, and the content is subject to change
without notice. The u dates will be added to the new
version of this manual. We will readily im rove or
u date the roducts or rocedures described in the
manual.
1Preface
1.1 Regulatory nformation
1.1.1 FCC nformation
Please take attention that changes or modification
not ex ressly a roved by the arty res onsible for
com liance could void the user’s authority to o erate
the equi ment.
FCC Compliance: This equi ment has been tested and
found to com ly with the limits for a Class A digital
device, ursuant to art 15 of the FCC Rules. These
limits are designed to rovide reasonable rotection
against harmful interference when the equi ment is
o erated in a commercial environment. This
equi ment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
O eration of this equi ment in a residential area is
likely to cause harmful interference, in which case the
user will be required to correct the interference at his
own ex ense.
Typ
e
Model
Type Camera
DS
-
2CE17U8T
-
IT
Type Camera
DS
-
2CE18U8T
-
IT3
UM DS-2CE1xU8T-ITx 042618NA 2
1.1.2 FCC Conditions
This device com lies with art 15 of the FCC Rules.
O eration is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must acce t any interference received,
including interference that may cause undesired
o eration.
1.1.3 EU Conformity Statement
This roduct and, if a licable, the
su lied accessories too are marked with
“CE” and com ly therefore with the
a licable harmonized Euro ean standards
listed under the Low Voltage Directive
2014/35/EU, the EMC Directive
2012/19/EU (WEEE Directive): Products
marked with this symbol cannot be
dis osed of as unsorted munici al waste in
the Euro ean Union. For ro er recycling,
return this roduct to your local su lier
u on the urchase of equivalent new
equi ment, or dis ose of it at designated
collection oints. For more information see:
www.recyclethis.info.
2006/66/EC (Battery Directive): This
roduct contains a battery that cannot be
dis osed of as unsorted munici al waste in
the Euro ean Union. See the roduct
documentation for s ecific battery
information. The battery is marked with this
symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For ro er recycling, return
the battery to your su lier or to a
designated collection oint. For more
information see: www.recyclethis.info.
1.1.4 ndustry Canada CES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
1.1.5 Safety nstruction
These instructions are intended to ensure that the
user can use the roduct correctly to avoid danger or
ro erty loss.
The recaution measure is divided into “Warnings”
and “Cautions.”
Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cautions: Injury or equi ment damage may occur if
any of the cautions are neglected.
Warnings
Follow these
safeguards to revent
serious injury or death.
Cautions
Follow these
recautions to revent
otential injury or
material
damage.
UM DS-2CE1xU8T-ITx 042618NA 3
1.1.6
Warnings
•In the use of the device, you must be in strict
com liance with the electrical safety regulations of
the nation and region.
•In ut voltage should meet both the SELV (Safety
Extra Low Voltage) and the Limited Power Source
with 12 VDC according to the IEC60950-1 standard.
Refer to technical s ecifications for detailed
information.
•The camera is owered by the external DC ower
su ly (12 VDC, 1 A) that com lies with the LPS,
and the out ut current of this external DC ower
su ly must be no more than 6 A.
•Do not connect multi le devices to one ower
ada ter to avoid over-heating or a fire hazard
caused by overload.
•Make sure that the lug is firmly connected to the
ower socket.
•Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is ado ted.
•If smoke, odor, or noise rise from the device, turn
off the ower at once and un lug the ower cord,
and then contact the service center.
•Never attem t to disassemble the camera by
un rofessional ersonal.
1.1.7
Cautions
•Do not dro the camera or subject it to hysical
shock.
•Do not touch sensor modules with fingers.
•Do not lace the camera in extremely hot, cold
(the o erating tem erature shall be -40° to 60° C),
dusty or dam locations, and do not ex ose it to
high electromagnetic radiation.
•If cleaning is necessary, use a clean cloth with a bit
of ethanol, and wi e it gently.
•Do not aim the camera at the sun or extra bright
laces.
•The sensor may be burned out by a laser beam, so
when any laser equi ment is in using, make sure
that the sensor surface will not be ex osed to the
laser beam.
•Do not ex ose the device to high electromagnetic
radiation or extremely hot, cold, dusty, or dam
environments.
•To avoid heat accumulation, good ventilation is
required for the o erating environment.
•Kee the camera away from liquid while in use for
non-water roof devices.
•While in delivery, the camera shall be acked in its
original acking, or acking of the same material.
UM DS-2CE1xU8T-ITx 042618NA 4
1.1.8 Mark Description
Table 0-1 Mark Descri tion
Mark
Descri tion
DC Vo
ltage
2ntroduction
2.1 Product Features
The camera is a licable for both indoor and outdoor
conditions. A lication scenarios include roads,
warehouses, underground arking lots, bars, etc..
The main features are as follows:
•8 MP high erformance CMOS sensor
•IR cut filter with auto switch
•OSD menu with configurable arameters
•Auto white balance
•internal synchronization
•SMART IR mode
•3-axis adjustment
2.2 Overview
This manual a lies to two ty es of bullet cameras.
The overviews of each ty e are shown in the figures
below.
2.2.1 Overview of Type Camera
Figure 1 Overview of Ty e I Camera
2.1.1
Overview of Type Camera
Figure 2 Overview of Ty e II Camera
3nstallation
Before you start:
•Make sure that the device in the ackage is in good
condition and all the assembly arts are included.
•Make sure that all the related equi ment is
owered off during the installation.
UM DS-2CE1xU8T-ITx 042618NA 5
•Check the s ecification of the roducts for the
installation environment.
•Check whether the ower su ly matches your
ower out ut to avoid the damage.
•Make sure the wall is strong enough to withstand
three times the weight of the camera and the
mount.
•If the wall is cement, insert ex ansion bolts before
installing the camera. If the wall is wooden, use
self-ta ing screws to secure the camera.
•If the roduct does not function ro erly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera for re air or maintenance
by yourself.
3.1 nstallation of Type Camera
3.1.1 Ceiling/Wall Mounting without Junction Box
Steps
:
1. Paste the drill tem late (su lied) where you want
to install the camera.
2. Drill the screw holes and the cable hole (o tional)
in the ceiling/wall according to the drill tem late.
Figure 3 Drill Tem late
Note:
Drill the cable hole when using the ceiling outlet to
route the cable.
3. Attach the bracket to the ceiling/wall and secure
the camera with su lied screws.
Figure 4 Fix the Camera to the Ceiling
UM DS-2CE1xU8T-ITx 042618NA 6
Note:
•The su lied screw ackage contains self-ta ing
screws and ex ansion bolts.
•For cement wall/ceiling, ex ansion bolts are
required to fix the camera. For wooden
wall/ceiling, self-ta ing screws are required.
4. Route the cables through the cable hole or the side
o ening.
5. Connect the corres onding ower cord and video
cable.
6. Power on the camera to check if the image on the
monitor is at an o timum angle. If not, adjust the
camera according to the figure below to get an
o timum angle.
Figure 5 3-axis Adjustment
1). Loosen the P screw to adjust the an osition
[0° to 360°]. Tighten the screw after
com leting the adjustment.
2). Loosen the T screw to adjust the tilt osition
[0° to 180°]. Tighten the screw after
com leting the adjustment.
3). Loosen the R screw and rotate the camera [0°
to 360°]. Tighten the screw after com leting
the adjustment.
3.1.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to urchase a junction box se arately.
Steps:
1. Paste the drill tem late on the ceiling/wall.
2. Drill screw holes, and the cable hole (o tional) in
the ceiling/wall according to the holes of the drill
tem late.
UM DS-2CE1xU8T-ITx 042618NA 7
Figure 6 Drill Tem late of Junction Box
Note:
Drill the cable hole when using the ceiling outlet to
route the cable.
3. Take a art the junction box, and align the screw
holes of the bullet camera with those on the
Junction box cover.
4. Fix the camera on the junction box’s cover with
su lied screws.
Figure 7 Fix the Camera on the Junction Box Cover
5. Attach the junction box body to the ceiling/wall by
aligning the screw holes of the junction box.
6. Secure the junction box body with su lied screws
on the ceiling/wall.
Figure 8 Fix the Junction Box to the Wall/Ceiling
UM DS-2CE1xU8T-ITx 042618NA 8
7. Route the cables through the bottom cable hole
(o tional) or the side cable hole of the junction
box.
8. Combine the junction box cover with its body.
Figure 9 Fix the Junction Box Cover Back to its Body
9. Re eat the ste 5 and 6 of 2.1.1 Ceiling/Wall
Mounting without Junction Box to com lete the
installation.
3.2 nstallation of Type Camera
3.2.1 Ceiling/Wall Mounting without Junction Box
Steps:
1. Paste the drill tem late (su lied) to the lace
where you want to install the camera.
2. Drill the screw holes according to the drill tem late
and the cable hole (o tional) on the ceiling/wall.
Figure 10 Drill Tem late
Note:
Drill the cable hole in the center of the drill tem late
when using ceiling outlet to route the cable.
3. Route the cables through the cable hole (o tional)
or the side o ening.
4. Fix the camera to the ceiling with su lied screws.
UM DS-2CE1xU8T-ITx 042618NA 9
Figure 11 Fix the Camera to the Ceiling
Note:
•The su lied screw ackage contains self-ta ing
screws, and ex ansion bolts.
•For cement wall/ceiling, ex ansion bolts are
required to fix the camera. For wooden
wall/ceiling, self-ta ing screws are required.
5. Connect the corres onding ower cord and video
cable.
6. Power on the camera to check if the image on the
monitor is at an o timum angle. If not, adjust the
surveillance angle.
Figure 12 3-Axis Adjustment
1). Loosen the No.1 adjusting screw to adjust the
an osition [0° to 360°]. Tighten the No.1
adjusting screw.
2). Loosen the No.2 adjusting screw to adjust the
tilting osition [0° to180°]. Tighten the No. 2
adjusting screw.
3). Loosen the No.3 adjusting screw to adjust the
rotation osition [0° to 360°]. Tighten the No.3
adjusting screw.
3.2.2 Ceiling/Wall Mounting with Junction Box
Before you start:
You need to urchase a junction box se arately.
Steps:
1. Paste the drill tem late on the ceiling/wall.
2. Drill screw holes and the cable hole (o tional) in
the ceiling/wall according to the holes of the drill
tem late.
UM DS-2CE1xU8T-ITx 042618NA 10
Figure 13 Drill Tem late
Note:
Drill the cable hole, when ado ting ceiling outlet to
route the cable.
3. Take a art the junction box, and align the screw
holes of the bullet camera with those on the
Junction box’s cover.
4. Fix the camera on the junction box cover with
three su lied screws.
Figure 14 Fix the Camera on the Junction Box Cover
5. Secure the junction box’s body with su lied
screws on the ceiling/wall.
Figure 15 Install the Junction Box
Altri manuali per DS-2CE17U8T-IT
1
Questo manuale è adatto per i seguenti modelli
1
Altri manuali HIK VISION Telecamera di sicurezza
HIK VISION
HIK VISION DS-2CD6362F-I Guida utente
HIK VISION
HIK VISION DS-2CE72DF3T-LSE Manuale utente
HIK VISION
HIK VISION DS-2CD2347G2-LSU Istruzioni per il montaggio
HIK VISION
HIK VISION DS-2TD2166 Manuale utente
HIK VISION
HIK VISION E-series Manuale utente
HIK VISION
HIK VISION DS-2XS6A25G0-I/CH20S40 Manuale utente
HIK VISION
HIK VISION DS-2CD7126G0/L-IZS Manuale utente
HIK VISION
HIK VISION DS-2CE16CoT-IRPF Manuale utente
HIK VISION
HIK VISION PTZ-N4225I-DE Manuale utente
HIK VISION
HIK VISION DS-2TD2667-15/PY Manuale utente
HIK VISION
HIK VISION DS-2DE2A204IW-DE3(C0)(S6) Manuale utente
HIK VISION
HIK VISION ECI-D64Z2 Manuale utente
HIK VISION
HIK VISION DS-2CD883F-E series Manuale utente
HIK VISION
HIK VISION DS-2CD7153 Manuale utente
HIK VISION
HIK VISION DS-2CV2G26G0-IDW Manuale utente
HIK VISION
HIK VISION DS-2TD4166-50/V2 Manuale utente
HIK VISION
HIK VISION DS-2CE10HFT-F Manuale utente
HIK VISION
HIK VISION 62 Series Manuale utente
HIK VISION
HIK VISION DS-2CE11D0T-PIRL Manuale utente
HIK VISION
HIK VISION UD06695B Manuale utente
