HIMA HIMax X-DO 32 51 Manuale utente

X-DO 32 51

HIMax®

Digital Output Module

Manual

HI 801 183 E Rev. 4.02 (1203)

All HIMA products mentioned in this manual are protected by the HIMA trade-mark. Unless noted otherwise,

this also applies to other manufacturers and their respective products referred to herein.

All of the instructions and technical specifications in this manual have been written with great care and

effective quality assurance measures have been implemented to ensure their validity. For questions, please

contact HIMA directly. HIMA appreciates any suggestion on which information should be included in the

manual.

Equipment subject to change without notice. HIMA also reserves the right to modify the written material

without prior notice.

For further information, refer to the HIMA DVD and our website at http://www.hima.de and

http://www.hima.com.

Contact

HIMA contact details:

HIMA Paul Hildebrandt GmbH + Co KG

P.O. Box 1261

68777 Brühl, Germany

Phone: +49 6202 709-0

Fax: +49 6202 709-107

E-mail: [email protected]

Type of change

Revision

index

Revisions

technical editorial

4.00 First Edition of the SILworX V4 Manual

4.01 Revised: Chapter 3.2 and 3.5 X X

4.02 Deleted: Redundant connector boards X X

X-DO 32 51 Table of Contents

HI 801 183 E Rev. 4.02 Page 3 of 50

Table of Contents

1Introduction 5

1.1 Structure and Use of this Manual 5

1.2 Target Audience 5

1.3 Formatting Conventions 6

1.3.1 Safety Notes 6

1.3.2 Operating Tips 7

2Safety 8

2.1 Intended Use 8

2.1.1 Environmental Requirements 8

2.1.2 ESD Protective Measures 8

2.2 Residual Risk 9

2.3 Safety Precautions 9

3Product Description 10

3.1 Safety Function 10

3.1.1 Reaction in the Event of a Fault 10

3.2 Scope of Delivery 10

3.3 Type Label 11

3.4 Structure 12

3.4.1 Block Diagram 13

3.4.2 Indicators 14

3.4.3 Module Status Indicators 15

3.4.4 System Bus Indicators 16

3.4.5 I/O Indicators 16

3.5 Product Data 17

3.6 Connector Boards 19

3.6.1 Mechanical Coding of X-CB 009 5X Connector Boards 19

3.6.2 Coding of X-CB 009 5X Connector Boards 20

3.6.3 Connector Board with Screw Terminals 21

3.6.4 Terminal Assignment for Connector Boards with Screw Terminals 22

3.6.5 Connector Board with Cable Plug 24

3.6.6 Pin Assignment for Connector Boards with Cable Plug 25

3.7 System Cable X-CA 006 26

3.7.1 Cable Plug Coding 27

Table of Contents X-DO 32 51

Page 4 of 50 HI 801 183 E Rev. 4.02

4Start-up 28

4.1 Mounting 28

4.1.1 Wiring Outputs not in Use 28

4.2 Mounting and Removing the Module 29

4.2.1 Mounting a Connector Board 29

4.2.2 Mounting and Removing the Module 31

4.3 Configuring the Module in SILworX 33

4.3.1 Tab: Module 34

4.3.2 Tab: I/O Submodule DO32_51 35

4.3.3 Tab: I/O Submodule DO32_51: Channels 36

4.3.4 Submodule Status [DWORD] 36

4.3.5 Diagnostic-Status [DWORD] 37

4.4 Connection Variants 38

4.4.1 1-Pole Wiring of Actuators 38

4.4.2 2-Pole Wiring of Actuators 38

4.4.3 Wiring Actuators to Redundant Modules 39

4.4.4 Wiring Inductive Loads 39

4.4.5 Wiring Actuators via Field Termination Assembly 40

5Operation 41

5.1 Handling 41

5.2 Diagnosis 41

6Maintenance 42

6.1 Maintenance Measures 42

6.1.1 Loading the Operating System 42

7Decommissioning 43

8Transport 44

9Disposal 45

Appendix 46

Glossary 46

Index of Figures 47

Index of Tables 48

Index 49

X-DO 32 51 1 Introduction

HI 801 183 E Rev. 4.02 Page 5 of 50

1 Introduction

The present manual describes the technical characteristics of the module and its use. It

provides information on how to install, start up and configure the module in SILworX.

1.1 Structure and Use of this Manual

The content of this manual is part of the hardware description of the HIMax programmable

electronic system.

This manual is organized in the following main chapters:

Introduction

Safety

Product Description

Start-up

Operation

Maintenance

Decommissioning

Transport

Disposal

Additionally, the following documents must be taken into account:

Name Content Document no.

HIMax

System manual

Hardware description of the

HIMax system

HI 801 001 E

HIMax

Safety manual

Safety functions of the HIMax

system

HI 801 003 E

HIMax

Communication manual

Description of communication

and protocols

HI 801 101 E

SILworX Online Help

(OLH)

Instructions on how to use

SILworX

First Steps Introduction to SILworX HI 801 103 E

Table 1: Additional Relevant Manuals

The latest manuals can be downloaded from the HIMA website at www.hima.com. The revision

index on the footer can be used to compare the current version of existing manuals with the

Internet edition.

1.2 Target Audience

This document addresses system planners, configuration engineers, programmers of

automation devices and personnel authorized to implement, operate and maintain the devices

and systems.

1 Introduction X-DO 32 51

Page 6 of 50 HI 801 183 E Rev. 4.02

1.3 Formatting Conventions

To ensure improved readability and comprehensibility, the following fonts are used in this

document:

Bold: To highlight important parts

Names of buttons, menu functions and tabs that can be clicked and

used in SILworX.

Italics: System parameter and variables

Courier Literal user inputs

RUN Operating state are designated by capitals

Chapter 1.2.3 Cross references are hyperlinks even though they are not

particularly marked. When the cursor hovers over a hyperlink, it

changes its shape. Click the hyperlink to jump to the corresponding

position.

Safety notes and operating tips are particularly marked.

1.3.1 Safety Notes

The safety notes are represented as described below.

These notes must absolutely be observed to reduce the risk to a minimum. The content is

structured as follows:

Signal word: danger, warning, caution, notice

Type and source of danger

Consequences arising from the danger

Danger prevention

The signal words have the following meanings:

Danger indicates hazardous situation which, if not avoided, will result in death or serious

injury.

Warning indicates hazardous situation which, if not avoided, could result in death or serious

injury.

Warning indicates hazardous situation which, if not avoided, could result in minor or modest

injury.

Notice indicates a hazardous situation which, if not avoided, could result in property damage.

NOTICE

Type and source of damage!

Damage prevention

SIGNAL WORD

Type and source of danger!

Consequences arising from the danger

Danger prevention

X-DO 32 51 1 Introduction

HI 801 183 E Rev. 4.02 Page 7 of 50

1.3.2 Operating Tips

Additional information is structured as presented in the following example:

The text corresponding to the additional information is located here.

Useful tips and tricks appear as follows:

TIP The tip text is located here.

2 Safety X-DO 32 51

Page 8 of 50 HI 801 183 E Rev. 4.02

2 Safety

All safety information, notes and instructions specified in this manual must be strictly observed.

The product may only be used if all guidelines and safety instructions are adhered to.

This product is operated in accordance with SELV or PELV. No imminent danger results from

the module itself. The use in Ex-Zone is permitted if additional measures are taken.

2.1 Intended Use

HIMax components are designed for assembling controller systems.

When using the components in the HIMax system, comply with the following general

requirements

2.1.1 Environmental Requirements

Requirement type Range of values

Protection class Protection class III in accordance with IEC/EN 61131-2

Ambient temperature 0...+60 °C

Storage temperature -40...+85 °C

Pollution Pollution degree II in accordance with IEC/EN 61131-2

Altitude < 2000 m

Housing Standard: IP20

Supply voltage 24 VDC

Table 2: Environmental Requirements

Exposing the HIMax system to environmental conditions other than those specified in this

manual can cause the HIMax system to malfunction.

2.1.2 ESD Protective Measures

Only personnel with knowledge of ESD protective measures may modify or extend the system

or replace modules.

NOTE

Device damage due to electrostatic discharge!

When performing the work, make sure that the working area is free of static and wear

an ESD wrist strap.

If not used, ensure that the device is protected from electrostatic discharge, e.g., by

storing it in its packaging.

X-DO 32 51 2 Safety

HI 801 183 E Rev. 4.02 Page 9 of 50

2.2 Residual Risk

No imminent danger results from a HIMax module itself.

Residual risk may result from:

Faults in the engineering

Faults in the user program

Faults in the wiring

2.3 Safety Precautions

Observe all local safety requirements and use the protective equipment required on site.

3 Product Description X-DO 32 51

Page 10 of 50 HI 801 183 E Rev. 4.02

3 Product Description

X-DO 32 51 is a digital NonSIL output module intended for use in the programmable electronic

system (PES) HIMax.

The module can be inserted into any of the base plate slots with the exception of the slots

reserved for system bus modules. For more information, see System Manual (HI 801 001 E).

The module is equipped with 32 digital outputs that can be loaded with a nominal current of up

to 0.5 A per channel. At high level, a voltage equivalent to the supply voltage is present on the

corresponding output.

The outputs are suitable for connecting ohmic, inductive and capacitive loads and lamps.

It can be operated with safety-related modules and other NonSIL modules within one base

plate. Safety-related and NonSIL modules may not be wired redundantly.

The module is interference-free, in particular, with respect to EMC, electrical safety,

communication to the X-SB and X-CPU modules, as well as the user program.

Module and connector boards are mechanically coded, see Chapter 3.6.1. Coding avoids

installation of improper modules.

Refer to the HIMax Safety Manual (HI 801 003 E) for more information on the standards used to

test and certify the modules and the HIMax system.

3.1 Safety Function

The module does not perform any safety-related functions.

Each switch of a channel can be individually switched off via the system bus (I/O bus).

The parameters and status for this module must not be used for safety functions.

3.1.1 Reaction in the Event of a Fault

If a channel fault occurs, the affected channel is switched off. If a module fault occurs, all

outputs are switched off.

If the system bus fails, the outputs are de-energized.

The module activates the Error LED on the front plate.

3.2 Scope of Delivery

The module must be installed on a suitable connector board to be able to operate. If a Field

Termination Assembly (FTA) is used, a system cable is required to connect the connector board

to the FTA. Connector boards, system cables and FTAs are not included within the scope of

delivery.

The connector boards are described in Chapter 3.6, the system cables are described in

Chapter 3.7. The FTAs are described in own manuals.

Indice

Altri manuali HIMA Unità di controllo

HIMA

HIMA HIMax X-AI 32 02 Manuale utente

HIMA

HIMA HIMax X-CI 24 51 Manuale utente

HIMA

HIMA HIMax X-DI 32 52 Manuale utente

HIMA

HIMA HIMax X-DI 32 05 Manuale utente

HIMA

HIMA HIMax X-DO 12 51 Manuale utente

HIMA

HIMA HIMax X-HART 32 01 Manuale utente

HIMA

HIMA HIMax X-COM 01 E Manuale utente

HIMA

HIMA HIMax X-SB 01 Manuale utente

HIMA

HIMA DIO 24/16 01 Manuale utente

HIMA

HIMA HIMax X-DI 32 02 Manuale utente

HIMA

HIMA HIMax X-DI 32 51 Manuale utente

HIMA

HIMA HIMax X-MIO 7 01 Manuale utente

HIMA

HIMA HIMax X-DI 64 51 Manuale utente

HIMA

HIMA HIMatrix F60 Manuale di installazione e funzionamento

HIMA

HIMA HIMax X-CI 24 01 Manuale utente

HIMA

HIMA HIMatrix F60 DI 32 01 Manuale utente

HIMA

HIMA HIMax X-DI 64 01 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente