Hioki 7016 Manuale utente

SIGNAL SOURCE

REMOTE OPERATION MANUAL

7016

Contents

i

Contents

Introduction.................................................................................1

Symbols......................................................................................1

Chapter 1

Remote Interface

Overview ___________________________________ 3

Chapter 2

Setting Remote Interface Parameters ___________ 5

Chapter 3

Commands Summary ________________________ 7

Chapter 4

Responding

Message ___________________________________ 9

Chapter 5

Instructions of

Command Sets_____________________________ 13

5.1 IEEE 488 Common Commands ..................................13

5.2 SCPI Commands ........................................................14

Chapter 6

Summary of SCPI

Commands ________________________________ 31

Chapter 7

Remote Program Example Using

______________________________ Visual Basic 637

Contents

ii

1

Introduction

Introduction

The Section describes how to operate the meter via an optical

interface.

• It also explains the detail information of all interface command sets

of Standard Commands for Programmable Instruments (SCPI) used

in the meter.

• The remote control operation enables the user either to manually

operate the meter via a terminal or to execute a host computer

program automatically.

Symbols

Safety Symbol

The following symbols in this manual indicate the relative importance

of cautions and warnings.

Other symbols

Indicates advisory items related to performance or

correct operation of the instrument.

Indicates the reference.

*Iterminology explained at the bottom of the word.

Symbols

2

3

Chapter 1 Remote Interface Overview

The following figure shows the USB type optical cable connecting for

the meter and a host computer communication.

The computer is added a virtual RS-232 COM port when the user

plugs the USB type cable and installs the USB driver.

• The remote interface is a serial binary data interchange, which

operates from 2400 to 19200 baud rate.

• The communication port of the 7016 is designed in full duplex,

which makes the meter more reliable and efficient in data taking.

Cable connection for Communication

Remote Interface

Overview Chapter 1

Chapter 1 Remote Interface Overview

4

5

Chapter 2 Setting Remote Interface Parameters

In order to operate the meter via a host computer or terminal, the

parameters in interface within the 7016 have to match the parameters

in the serial interface provided by the host or terminal.

The following procedures will guide the user to set up interface

parameters within the 7016 to comply interface with the host.

The default settings of the meter at factory are 9600-baud rate, non-

parity, 8 data bits, and 1 stop bit (9600, n, 8, 1).

The following table indicates the factory settings and user selectable

communication parameters by using remote interface.

Echo

With ECHO ON, the meter echoes (returns) all the characters

whatever it receives.

Print-Only

• The remote indicator of the 7016 is flashing when the meter is set to

Print-Only ON.

• If the remote interface of the 7016 is under Print-Only mode, the

7016 will print out the measured data when the measurement cycle

is completed.

• The 7016 auto-sends the newest data to a host continuously.

• The 7016 doesn't accept any commands under Print-Only mode.

Setup Procedures for Communication Parameter

To ensure the remote interface will operate appropriately, user may

need to configure the remote interface parameters on Setup Mode.

Please refer to operation procedures of POWER-ON OPTION.

❖7016 instruction manual 5.4 Power-On Options

Setting Remote Interface

Parameters Chapter 2

Remote Interface Parameters

Item Parameter Factory

Setting Selectable Parameter

1Baud Rate 9600 2400, 4800, 9600, 19200

2Parity None None, Odd or Even

3Data Bit 8 7 or 8

4ECHO OFF ON or OFF

5Print-Only OFF ON or OFF

Chapter 2 Setting Remote Interface Parameters

6

Altri manuali per 7016

2

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente