Hirschmann RSPL 20 Manuale utente

Installation RSPL 20/30

Release

02/2013

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial Ethernet Rail Switch Power Lite

RSPL 20/30

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Installation RSPL 20/30 040 016-001-04-0213 - 19.02.2013

Installation RSPL 20/30

Release

02/2013 3

Contents

Safety instructions 5

About this manual 12

Key 12

1 Device description 13

1.1 General device description 13

1.2 Device name and product code 14

1.3 Combination options 17

1.4 Device views 18

1.4.1 Front view 18

1.4.2 Rear view 20

1.5 Power supply 20

1.5.1 Operating voltage type M9 20

1.5.2 Operating voltage type CC 20

1.6 Ethernet ports 21

1.6.1 Gigabit combo port (optional) 21

1.6.2 10/100 Mbit/s twisted pair connection 22

1.6.3 100 Mbit/s F/O connection 22

1.7 Display elements 23

1.7.1 Device state 23

1.7.2 Port state 24

1.8 Management interfaces 24

1.8.1 V.24 interface (external management) 24

1.8.2 SD card interface 25

1.9 Signal contact 26

2 Device installation 27

2.1 Unpacking and checking 27

2.2 Installing the SD card (optional) 27

2.3 Installing the device and grounding 28

2.3.1 Mounting on the DIN rail 28

2.3.2 Grounding 29

2.4 Installing the SFP transceivers (optional) 29

2.5 Connecting the terminal blocks 30

4Installation RSPL 20/30

Release

02/2013

2.6 Mounting the terminal blocks and switching on the supply

voltage 33

2.7 Connecting the data lines 33

2.7.1 Gigabit combo port (optional) 33

2.7.2 100 Mbit/s F/O connection 34

2.7.3 10/100 Mbit/s twisted pair connection 34

2.8 Insert data in label area 34

3 Basic set-up 35

4 Monitoring the ambient air temperature 36

5 Maintenance and service 37

6Disassembly 38

6.1 Disassembling the device 38

6.2 Removing the SFP transceivers 39

7 Technical data 40

A Further Support 52

Installation RSPL 20/30

Release

02/2013 5

Safety instructions

Certified usage

Only use the device for application cases that are described in the

Hirschmann product information, including this manual. Only operate the

device according to the technical specifications.

Supply voltage

Note: The supply voltage is only connected with the chassis via protective

elements.

Only for device variants with operating voltage type M9:

For the supply voltage to be connected, make sure the following

requirements are met:

The power supply conforms to overvoltage category I or II.

The voltage supply has an easily accessible disconnecting device

(e.g. a switch or a plug). This disconnecting device is clearly

identified so that in the case of an emergency, it is clear which

disconnecting device belongs to which line.

The lines to be connected are voltage-free.

Supply with DC voltage:

A fuse suitable for DC voltage is located in the plus conductor of the

power supply. A fuse is also located in the minus conductor, if this

is not grounded.

Regarding the properties of this fuse: See “General technical data”

on page 40.

Supply with AC voltage:

A fuse is located in the outer conductor of the power supply. A fuse

is also located in the neutral conductor, if this is not grounded.

Regarding the properties of this fuse: See “General technical data”

on page 40.

AC voltage Supply: the wire diameter for the input supply line is at

least 0.75 mm² (North America: AWG18).

DC voltage Supply: the wire diameter for the input supply line is at

least 1 mm² (North America: AWG16).

WARNING

ELECTRIC SHOCK

Ground the device before connecting the power supply.

Only connect a supply voltage as described in the data plate of your device.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RSPL 20/30

Release

02/2013

The cross-section of the protective conductor cable is the same

size as or bigger than the cross-section of the voltage supply

cables.

The connection cables used are permitted for the specified

temperature range.

Relevant for North America:

The power supply lines are made up of copper wire (75 °C).

Only for device variants with operating voltage type CC:

For every supply voltage to be connected, make sure the following

requirements are met:

The power supply corresponds to Class 2.

The power supply conforms to overvoltage category I or II.

The voltage supply has an easily accessible disconnecting device

(e.g. a switch or a plug). This disconnecting device is clearly

identified so that in the case of an emergency, it is clear which

disconnecting device belongs to which line.

The lines to be connected are voltage-free.

A fuse suitable for DC voltage is located in the plus conductor of the

power supply. A fuse is also located in the minus conductor, if this

is not grounded.

Regarding the properties of this fuse: See “General technical data”

on page 40.

The wire diameter for the input supply line is at least 1 mm² (North

America: AWG16).

The connection cables used are permitted for the specified

temperature range.

Relevant for North America:

The power supply lines are made up of copper wire (75 °C).

WARNING

ELECTRIC SHOCK

Only start connecting the supply voltage if all the above mentioned

requirements are fulfilled.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation RSPL 20/30

Release

02/2013 7

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

Use undamaged parts.

The device does not contain any service components. Internal fuses

are only triggered if there is a fault in the device. If the device is not

functioning correctly, or if it is damaged, switch off the voltage supply

and return the device to the plant for inspection.

Connect the protective conductor with the ground screw before you

set up the other connections. When removing the connections, you

remove the protective conductor last.

For supply voltages with protective conductor connections: first

connect the protective conductor before connecting the lines for the

supply voltages.

Only switch on the supply voltage for the device when the following

prerequisites are fulfilled:

The housing is closed

The terminal blocks are wired correctly

The terminal blocks for the voltage supply are connected

Shielded ground

The shielded ground wire of the twisted pairs lines is connected to the

front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shield braiding.

8Installation RSPL 20/30

Release

02/2013

Housing

Only technicians authorized by the manufacturer are permitted to open

the housing.

WARNING

ELECTRIC SHOCK

Never insert sharp objects (small screwdrivers, wires, etc.) into the inside of

the device.

Never insert sharp objects (small screwdrivers, wires, etc.) into the

connection terminals for the supply voltage or the signal contact, and do not

touch the terminals!

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

WARNING

FIRE HAZARD

Install the device in a fire protected enclosure according to EN 60950-1.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

WARNING

Only for device variants with operating voltage type M9:

ELECTRIC SHOCK

Only install this device in a switch cabinet or in an operating site with limited

access, to which only maintenance staff have access.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation RSPL 20/30

Release

02/2013 9

The device is grounded by the separate ground screw on the front panel.

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

Keep the ventilation slits free to ensure good air circulation.

Make sure there is at least 10 cm of space in front of the ventilation

slits of the housing.

Install the device in the vertical position.

Environment

Operate the device at the specified surrounding air temperature

(temperature of the surrounding air at a distance of up to 1.97 in (5 cm)

from the device) and relative air humidity specified in the technical data.

When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

Use the device in an environment within the pollution degree specified

in the technical data.

Qualification requirements for personnel

Qualified personnel as understood in this manual and the warning signs,

are persons who are familiar with the setup, assembly, startup, and

operation of this product and are appropriately qualified for their job. This

includes, for example, those persons who have been:

trained or directed or authorized to switch on and off, to ground and to

label power circuits and devices or systems in accordance with current

safety engineering standards;

trained or directed in the care and use of appropriate safety equipment

in accordance with the current standards of safety engineering;

trained in providing first aid.

General safety instructions

This device is operated by electricity. You must follow precisely the

prescribed safety requirements for the voltage connections in this

document.

See “Supply voltage” on page 5.

10 Installation RSPL 20/30

Release

02/2013

Non-observance of these safety instructions can cause material damage

and/or injuries.

Only appropriately qualified personnel should work on this device or in

its vicinity. The personnel must be thoroughly familiar with all the

warnings and maintenance procedures outlined in this operating

manual.

The proper and safe operation of this device depends on proper

handling during transportation, proper storage and assembly, and

conscientious operation and maintenance procedures.

Never start operation with damaged components.

Only use the devices in accordance with this manual. In particular,

observe all warnings and safety-related information.

Any work that may be required on the electrical installation may only

be carried out by personnel trained for this purpose.

Note: LED or LASER components in compliance with IEC 60825-1

(2007):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

National and international safety regulations

Make sure that the electrical installation meets local or nationally

applicable safety regulations.

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Device variant Directive

All variants 2004/108/EG (EMV)

Directive of the European Parliament and the council for

standardizing the regulations of member states with regard to

electromagnetic compatibility.

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the

restriction of the use of certain hazardous substances in

electrical and electronic equipment.

Only for device variants with

operating voltage type M9:

2006/95/EC

Directive of the European Parliament and the council for

standardizing the regulations of member states with regard to

electrical equipment to be used within specific voltage ranges.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hirschmann Interruttore

Hirschmann

Hirschmann BATOne Manuale utente

Hirschmann

Hirschmann LRS Series Manuale utente

Hirschmann

Hirschmann MAR1042 Manuale utente

Hirschmann

Hirschmann Octopus II Manuale utente

Hirschmann

Hirschmann Power MICE Manuale utente

Hirschmann

Hirschmann MSM20 Manuale utente

Hirschmann

Hirschmann GRS103 Series Manuale utente

Hirschmann

Hirschmann RH1-CX+ Manuale utente

Hirschmann

Hirschmann LION-GIGA-1SX Manuale utente

Hirschmann

Hirschmann SPIDER 8TX-PRO Manuale utente

Hirschmann

Hirschmann PowerLION-24TP Manuale utente

Hirschmann

Hirschmann OCTOPUS 8M Series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann GECKO 4TX Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann OCTOPUS OS20 Manuale utente

Hirschmann

Hirschmann PowerMICE MS4128 Manuale utente

Hirschmann

Hirschmann GigaLION-24TP Manuale utente

Hirschmann

Hirschmann RS1 Series Manuale

Hirschmann

Hirschmann OCTOPUS 8M Series Manuale utente

Hirschmann

Hirschmann MACH 4000 Series Manuale utente

Hirschmann

Hirschmann SPIDER 5TX Manuale

Hirschmann

Hirschmann GREYHOUND GRS1020 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente