Hirschmann RS20 series Manuale utente

Installation RS20/22/30/32/40

Release

12/2015

Technical support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Industrial ETHERNET Rail Switch

RS20/RS22/RS30/RS32/RS40 Family

RS30-0802...

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS30-1602...

RS20

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS30

+24V(P1) 0V 0V

FAULT

+24V(P2)

LS DA

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

LS DA

V.24

USB

Stand by

FAULT

RS20

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0800...RS20-2400... RS20-0400...

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS20-0900...

RS40

+24V(P1) 0V 0V

FAULT

+24V(P2)

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

RS40-0009... RS32-0802... RPS90/48V HV

RPS90/48V HV

U: 110 / 230 VAC

U: 60 / 250 VDC

-/N

+/L

+48V / 1,9A

48-54V

RS32

Stand by

Aufkleber MAC-Adresse

IP-ADDRESS

V.24

USB

Stand by

FAULT

LS DA

+24V(P1) 0V 0V

FAULT

+24V(P2)

FAULT

+48V(P1) 0V 0V +48V(P2)

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the

enclosed CD/DVD applies.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

RS20/22/30/32/40 039 692-003-05-1215

Installation RS20/22/30/32/40

Release

12/2015 3

Contents

Safety instructions 5

About this Manual 18

Key 18

1 Description 19

1.1 Description of the device variants 21

1.1.1 Combination options of the device variants

RS20/RS30/RS22/RS32 23

1.1.2 Combination options for the RS40 device variants 26

1.1.3 Number of ports and media for RS20-... 27

1.1.4 Number of ports and media for RS30-... 31

1.1.5 Number of ports and media for RS40-... 34

1.2 Device variants with PoE (optional) 35

1.2.1 Number of ports and media for devices with PoE 35

1.2.2 PoE power units 37

1.3 Ethernet ports 38

1.3.1 10/100/1000 Mbit/s twisted pair port 38

1.3.2 10/100 Mbit/s twisted pair port 39

1.3.3 10/100 Mbit/s twisted-pair connection PoE

(RS22-.../RS32-...) 39

1.3.4 1000 Mbit/s F/O port 40

1.3.5 100 Mbit/s F/O port 40

1.3.6 Gigabit combo port 41

1.4 Display elements 42

1.5 Management interfaces 44

1.5.1 USB interface 44

1.5.2 V.24 interface (external management) 44

2 Installation 45

2.1 Checking the package contents 46

2.2 Installing and grounding the device 46

2.2.1 Installing the device onto the DIN rail 46

2.2.2 DIN rail mounting on ships (RS30-0802...) 48

2.2.3 Mounting on a vertical flat surface 49

2.2.4 Grounding the device 49

2.3 Installing an SFP transceiver (optional) 50

2.4 Adjust DIP switch settings 50

4Installation RS20/22/30/32/40

Release

12/2015

2.5 Connecting the terminal block 51

2.5.1 RS20/RS30/RS40: supply voltage and signal contact 51

2.5.2 RS22/RS32: supply voltage and signal contact 53

2.6 Mounting the terminal block 56

2.7 Connecting the ferrite 57

2.8 Operating the device 57

2.9 Connecting data cables 58

2.10 Filling out the inscription label 58

3 Making basic settings 59

4 Monitoring the ambient air temperature 60

5 Maintenance and service 61

6Disassembly 62

6.1 Removing the device 62

6.2 Removing an SFP transceiver (optional) 63

7 Technical data 64

A Further Support 78

Installation RS20/22/30/32/40

Release

12/2015 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the device solely for the application cases described in the

Hirschmann product information, including this manual.

Operate the device solely according to the technical specifications.

See “Technical data” on page 64.

Installation site requirements

Install the device in a fire enclosure according to EN 60950-1.

If installed in a living area or office environment, the device must be

operated only in switch cabinets with fire protection characteristics

according to EN 60950-1.

Only when using the PoE power supply unit RPS90/48V HV:

Install the device at ambient temperatures greater than 113 °F (45 °C)

in “restricted access locations” based on EN 60950-1 exclusively.

Install this device solely in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation RS20/22/30/32/40

Release

12/2015

Device casing

Only technicians authorized by the manufacturer are permitted to open

the housing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the ventilation slits free to ensure good air circulation.

See “General technical data” on page 64.

Install the device in the vertical position.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets locally or nationally applicable

safety regulations.

Grounding the device

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least 1.0

mm² (AWG16).

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Shielding ground

The overall shield of a connected shielded twisted pair cable is connected

to the ground connector on the front panel as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation RS20/22/30/32/40

Release

12/2015 7

Supply voltage

The supply voltage is electrically isolated from the housing.

The devices are designed for operation with safety extra-low voltage.

Connect only SELV circuits with voltage restrictions in line with IEC/EN

60950-1 to the supply voltage connections and signal contacts.

Connect only a supply voltage that corresponds to the type plate of

your device.

Observe the maximum values for the contact load of the signal

contact.

Relevant for North America:

The device may only be connected to a Class 2 supply voltage that

fulfills the requirements of the National Electrical Code, Table 11(b). If

the voltage is being supplied redundantly (two different voltage

sources), the combined supply voltages must fulfill the requirements of

the National Electrical Code, Table 11(b).

Relevant for North America: For use in class 2 circuits.

Use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire only.

Relevant for North America

for devices certified for hazardous locations:

Power, input and output (I/O) wiring must be in accordance with

Class I, Division 2 wiring methods [Article 501-4(b) of the National

Electrical Code, NFPA 70] and in accordance with the authority having

jurisdiction.

Start connecting the electrical wires only if all the above safety

requirements are fulfilled.

Enable the supply voltage for the device only when the following

requirements are fulfilled:

the housing is closed

the terminal blocks are wired correctly

the terminal blocks for the power supply are connected

Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

supply voltage and return the device to the plant for inspection.

8Installation RS20/22/30/32/40

Release

12/2015

Supply voltage for PoE power supply units (optional)

Connect the protective conductor with the ground screw before you set

up the other connections. When removing the cables, remove the

protective conductor last.

Make sure that the cross-section of the protective conductor cable is

the same size as or bigger than the cross-section of the voltage supply

cables.

Only use connection cables that are permitted for the specified

temperature range.

Connect only a supply voltage that corresponds to the type plate of

your device.

PoE power supply unit RPS90/48V LV:18 V DC to 60 V DC

PoE power supply unit RPS90/48V HV:48 V DC to 320 V DC or 90

V AC to 265 V AC

Install a suitable input fuse in the following cases:

The neutral conductor or the negative terminal of the supply voltage

is ungrounded.

For the supply voltage, you provide a DC voltage greater than

125 V DC.

See “General technical data” on page 64.

With AC power supply, use a cable cross-section of at least 0.75 mm²

(for North America AWG 18) for the current conductor at the voltage

input.

With DC power supply, use a cable cross-section of at least 1.0 mm²

(for North America AWG 16) for the current conductor at the voltage

input.

Installation RS20/22/30/32/40

Release

12/2015 9

ATEX directive 94/9/EG – specific regulations for safe

operation

Relevant for RS20/22/30/32/40 devices when operating in explosive gas

atmospheres according to ATEX Directive 94/9 EC, the following applies:

List of standards:

EN 60079-0:2012 + A11:2013

EN 60079-15:2010

Certificate No.: DEKRA 11ATEX0139 X or KEMA 09ATEX0067 X.

Make sure that the device has the following label:

II 3G Ex nA IIC T4 Gc DEKRA 11ATEX0139 X

for RS20/22/30/32 types.

II 3G Ex nA IIC T3 ... T4 Gc KEMA 09ATEX0067 X

for RS40 types.

Ambient rating and temperature code for RS20 and RS30 types:

T4: 0 °C ≤Ta ≤+60 °C for “S” types

(item 14 of nomenclature breakdown) or

T4: −40 °C ≤Ta ≤+70 °C for “T” or “E” types

(item 14 of nomenclature breakdown).

Ambient rating and temperature code for RS22 and RS32 types:

T4: −40 °C ≤Ta ≤+50 °C for “T” or “E” types

(item 14 of nomenclature breakdown) or

T4: 0 °C ≤Ta ≤+50 °C for “S” types

(item 14 of nomenclature breakdown)

Ambient rating and temperature code for RS40 types:

T3: −40 °C ≤Ta ≤+70 °C for “T” or “E” types

(item 14 of nomenclature breakdown).

T4: −40 °C ≤Ta ≤+60 °Cfor “T” or “E” types

(item 14 of nomenclature breakdown).

T4: 0 °C ≤Ta ≤+60 °C for “S” types

(item 14 of nomenclature breakdown).

The modules shall be installed in a suitable enclosure in accordance

with EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

When the temperature under rated conditions exceeds 70 °C at the

cable or conduit entry point, or 80 °C at the branching point of the

conductors, the temperature specification of the selected cable and

cable entries shall be in compliance with the actual measured

temperature values.

10 Installation RS20/22/30/32/40

Release

12/2015

Provisions shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 119 V.

Connectors shall be connected or disconnected exclusively in dead-

voltage state.

DIP switches shall be switched exclusively in dead-voltage state.

The USB port shall remain disconnected.

Altri manuali per RS20 series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hirschmann Interruttore

Hirschmann

Hirschmann OS20-001000T5T5TAFUHB Manuale utente

Hirschmann

Hirschmann GRS103 Series Manuale utente

Hirschmann

Hirschmann BXS Manuale utente

Hirschmann

Hirschmann LRS Series Manuale utente

Hirschmann

Hirschmann RSPM20-4Z64Z6 Series Manuale utente

Hirschmann

Hirschmann GREYHOUND GRS1020 Manuale utente

Hirschmann

Hirschmann MACH 100 Manuale utente

Hirschmann

Hirschmann BATOne Manuale utente

Hirschmann

Hirschmann LION-GIGA-1SX Manuale utente

Hirschmann

Hirschmann GREYHOUND GMM42 Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann OCTOPUS 8M Series Manuale utente

Hirschmann

Hirschmann RH1-CX+ Manuale utente

Hirschmann

Hirschmann RH1-TP Manuale

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann Octopus II Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann MSM20 Manuale utente

Hirschmann

Hirschmann MACH1000 Series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RS2-5TX/FX Manuale

Hirschmann

Hirschmann MSP30 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente