Hisense HL3215STG Manuale utente

HL3215STG is an integrated WIFI& Bluetooth BLE dual-mode module，BK7231M_QFN32--

integrated MCU/WLAN MAC/ Baseband/RF single chip scheme. ARM9 32-bit MCU core,

120MHz main frequency, built-in 256KBRAM.

•Supports 802.11b/G/N WIFI standard.

•Supports 802.11b/ G/N standards, HT-20

•Supports Station, Soft AP, Station+Soft AP

•With 20MHz bandwidth, the maximum transmission rate reaches 72.2Mbps

•Module built-in onboard antenna (for the antenna part, please refer to the antenna specification)

•working voltage：DC 3.3-3.6V，

•Supports BLE 5.2standard，

•Supports 802.11 b/g/n 1x1 protocol

•802.11b: 1, 2, 5.5, 11

•802.11g: 6, 9, 12, 18, 24, 36, 48, 54

•802.11n HT20: MCS0~7

•Supports STA/AP/Direct/Repeaternetwork model

•Supports SGI、Green-Field Preamble and A-MPDU

•Supports WPA,WPA2,WAPI security regime

•Supports 50 MHz SDIO port

•On - chip 2M FLASH, can be expanded to 4M, support transparent download

Function description

HLW3215-TG is a Wi-Fi module used in home appliances, and the first batch of home appliances

are dishwasher and oven. The hardware and software architecture based on the module can

realize the networking and the control of home appliances. Dishwasher and oven are controlled

by the module to achieve their local control functions. They are connected to the cloud server

through Wi-Fi and Bluetooth. Users can control the dishwasher and oven through the mobile

terminal App to achieve remote control, and can connect to the Hisense Connectlife intelligent

platform with intelligent and convenient use experience. In addition, the module supports OTA

upgrades and can also assist in OTA upgrades of the MCU plate for dishwashers and ovens.

We will retain control over the final installation of the modular such that compliance of the end

product is assured. If any hardware modify or RF control software modify will be made by host

manufacturer, C2PC or new certificate should be apply to get approval,if those change and

modification made by host manufacturer not expressly approved by the party responsible for

compliance ,then it is illegal.

The host device must be labeled to display the FCC ID of the module “Contains FCC

ID: 2A9F9HL3215STG”

The devices must be installed and used in strict accordance with the manufacturer's instructions

as described in the user documentation that comes with the product.

Any company of the host device which install the modular with modular approval should perform

the test of radiated & conducted emission and spurious emission, etc. according to FCC part 15C :

15.407,15.247 and 15.209 & 15.207 ,15B Class B requirement, Only if the test result comply with

FCC part 15C : 15.407,15.247 and 15.209 & 15.207 ,15B Class B requirement，then the host can

be sold legally.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

The modular can be installed or integrated in mobile or fix devices . This modular cannot be

installed in any portable device if without further certification such as C2PC with SAR. This

modular complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter. This modular must be installed and operated with a minimum distance of

20 cm between the radiator and user body.

IC warning

- English:

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to

the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

RF warning statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

- French:

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement

Avertissement RF:

Cet appareil est conforme à IC l’exposition aux rayonnements limites fixées pour un

environnement non contrôlé. Cet appareil doit être installé et utilisé avec une distance minimale

de 20 cm entre le radiateur et votre corps. Cet transmetteur ne doit pas être co-situé ou opérant

en liaison avec toute autre antenne ou transmetteur.

IC Radiation Exposure Statement

The modular can be installed or integrated in mobile or fix devices only. This modular cannot be

installed in any portable device.

This modular complies with IC RF radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter. This modular must be installed and operated with a minimum distance of

20 cm between the radiator and user body. Cette modulaire doit être installé et utilisé à une

distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur.

If the IC number is not visible when the module is installed inside another device, then the

outside of the device into which the module is installed must also display a label referring to the

enclosed module. This exterior label can use wording such as the following:

“Contains IC: 29823-HL3215STG”

when the module is installed inside another device, the user manual of this device must contain

below warning statements;

1. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

2. Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)

d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis

aux

deux conditions suivantes:

(1) Cet appareil ne doit pas causer d'interférences.

(2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de

provoquer un fonctionnement indésirable de l'appareil.

The devices must be installed and used in strict accordance with the manufacturer's instructions

as described in the user documentation that comes with the product.

Indice

Altri manuali Hisense Unità di controllo

Hisense

Hisense AEH-W4AI Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente