Hobo S-FS-TRMSA Manuale utente
FlexSmart™ TRMS Module (S-FS-TRMSA & S-FS-TRMSA-D) Manual
10093-H MAN-S-FS-TRMSA
The S-FS-TRMSA and S-FS-TRMSA-D are easy-to-configure, True-RMS input measurement
modules. The S-FS-TRMSA is compatible with HOBO® H22 series data loggers. The S-FS-TRMSA-D
is compatible with HOBO H22 loggers, U30 stations, and RX3000 stations. The “-D” variant has a
modular connector for connecting to an available smart-sensor port. Both 2-channel modules
have an input range of 512 millivolts RMS full-scale. Thus, they are fully compatible with
industry-standard voltage and current transformers (PT and CT) which output 333 millivolts RMS
full-scale.
The modules feature extremely low-power operation, resulting in long battery life for
unattended data logging applications.
Note: Refer to the H22 logger, U30 or RX3000 station, and HOBOware® software manuals at
www.onsetcomp.com/support/manuals for additional information on using and configuring the
FlexSmart TRMS module.
Specifications
Input Channels Two; AC-coupled
Field Wiring Two-wire via screw terminals on detachable connector, 16-24 AWG
Replacement detachable connectors: Part of spares kit (A-FS-TRMSA-
4P-1)
Input Range 5 to 512 mVRMS
Minimum Input Voltage 5mVRMS; Input voltages < 5mV will be clipped to zero (see graph
below)
Maximum Input Voltage ±1V referred to AC- terminals (pins 2 and 4)
Input Frequency 50/60 Hz
A
ccuracy ±0.3% of reading +/- 0.5% of FSR
ADC Resolution 15 bits
AC Waveform <4 Crest Factor
Power Requirements +3.3V @ 3mA active, 6μA sleep
Transfer Function
()
[]
•=
T
dttV
T
VRMS
0
2
1
Measurement Averaging Option Yes
The CE Marking identifies this product as complying with all relevant
directives in the European Union (EU).
Minimum Input Voltage Graph
FlexSmart TRMS Module
Models: S-FS-TRMSA
S-FS-TRMSA-D
Included Items:
•Detachable screw terminal
connector
•Imprintable label
FlexSmart TRMS Module (S-FS-TRMSA & S-FS-TRMSA-D) Manual
1-800-LOGGERS (564-4377) • 508-759-9500
www.onsetcomp.com/support/contact
© 2008–2018 Onset Computer Corporation. All rights reserved. Onset, HOBO, FlexSmart, HOBOware, and
HOBOlink are trademarks or registered trademarks of Onset Computer Corporation. All other trademarks are
the property of their respective companies.
10093-H MAN-S-FS-TRMSA
Module Connections
Potential Transformers (PT) and Current Transducers (CT) are
connected to the module via a four-pin Phoenix-style
detachable screw terminal connector. Once the PTs and/or CTs
are connected, the module can then be configured using
HOBOware software with the module installed on the HOBO
H22 or U30 series logger or using HOBOlink® with the RX3000
station. Note: There are limitations to the number of modules
and smart sensors you can use with an RX3000 station. If you
are using both TRMSA-D modules and smart sensors, then you
are limited to a maximum of three TRMSA-D and any
combination of smart sensors to reach a total of 13 data
channels. For example, if there are three TRMSA-D modules in
use with the RX3000 station (each module has two channels for
a total of six in all), then this will leave seven additional data
channels for smart sensors. Similarly, if there are two TRMSA-D
modules in use with RX3000 station, then this will leave nine
additional data channels for smart sensors. Refer to the smart
sensor manuals at www.onsetcomp.com/support/manuals for
the number of data channels used by a specific smart sensor. If
you are not using smart sensors with the RX3000 station, then
you are limited to a maximum of four TRMSA-D modules.
Exceeding these guidelines may result in erroneous readings.
The diagram below illustrates typical connections for a PT and
CT. For module connection instructions specific to PTs and CTs
purchased from Onset, refer to the documentation provided
with each PT and CT.
Note: For three-phase monitoring, each of the three modules
should be wired so that similar parameters are connected to
corresponding pin numbers. For example, voltage inputs pins 1
and 2 on each module; current inputs pins 3 and 4 on each
module.
Measurement Averaging
This module supports measurement averaging. When
measurement averaging is enabled, data is sampled more
frequently than it is logged. The multiple samples are then
averaged together and the average value is stored as the data
for the interval. For example, if the logging interval is set at 10
minutes and the sampling interval is set at 1 minute, each
recorded data point will be the average of 10 measurements.
Measurement averaging is useful for reducing noise in the data.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Hobo Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
