Honeywell Silent Knight 5860 Manuale tecnico

5860/5860R

Remote Fire Annunciator

Product Installation Document

Document 151042:E 2/15/2022 ECN: 151062

1 Description

The 5860 (gray) and 5860R (red) are optional 4x20 remote annunciators

that can be surface or flush-mounted.

2 Compatibility

The 5860/R is compatible with Honeywell Silent Knight FACPs. For

more information, see the FACP Installation manual.

3 Specifications

4 Installing the 5860/R

5860/R installation involves the following steps:

1. Ensure power is turned off at the panel.

2. Mount the 5860/R in the desired location.

3. Connect the 5860/R to the panel (see Figure 5).

4. Use the DIP switches on the back of the 5860/R to assign an ID

number. See the FACP Manual for more details.

5. The new 5860/R module must be added to the system through

programming. The JumpStart®Auto-programming feature will add

the module automatically. Refer to the FACP Manual for more

information.

5 Mounting

The 5860/R comes from the factory fully assembled. You must disas-

semble it for mounting. To disassemble the annunciator, use a 5/64” hex

wrench to remove the set screws, located on the bottom of the annuncia-

tor bezel.

FIRE ALARM ANNUNCIATOR

Figure 1 5860/R Remote Annunciator

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 58 mA

Alarm: 68 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

1".25

(3.175cm)

6.44"

(16.35cm)

8"(20.64cm).125

7".375

(18.73cm)

1”

.25

(3.175cm)

Figure 2 Annunciator Dimensions

backbox bezel

side

view

5860/5860R Installation Document — P/N 151042:E 2/15/2022 2

5.1 Surface Mounting

The 5860/R can be mounted directly to a surface or can be attached to a

single, double, or four-square electrical box. Trim Ring Kit 5860TG

(gray) and 5860TR (red) available for use when surface mounting.

1. Drill holes in the surface to match the screw holes on the backbox.

Refer to Figure 4.20 for locations.

2. Fit the trim ring over the backbox, if used.

3. Attach the backbox to the wall using screws provided.

5.2 Flush-Mounting

1. Cut a hole in the sheet rock to the following dimensions: 8.25” W x

6.625” H. If an electrical box is used, the box must be 1.375” back

from face of wall to accommodate the annunciator.

2. Remove knockout holes as needed for wires.

3. Fit the annunciator backbox into the hole and stabilize with

mounting wires. Angle the mounting wires into the first hole past

the sheet rock. Secure the wires behind the screws as shown in

Figure 4. When all four wires are in place, the backbox should fit

snugly into the hole in the sheetrock.

4. After the annunciator wiring to the panel has been completed (refer

to Figure 4.22), replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws on the

bezel.

5.2.1 Flush-Mounting with an Electrical Box

The 5860/R annunciator can be used with the following types of electri-

cal boxes: 4S, single-gang, and double-gang.

If an electrical box is used, the box must be 1.375” back from the face of

the wall to accommodate the annunciator. Studs used with an electrical

box must be 2x4” (or larger).

6 Wiring Connections

Wire the 5860/R to the FACP as shown below.

Figure 3 Trim Ring for Surface-mounting

backbox

trim ring

Attach second set of wires to top of backbox.

Secure wires behind screw.

Insert wires at an angle into the

first holes past sheetrock.

Figure 4 Flush Mounting the Backbox

SBUS OUT

–+AB

SB SA S+ S-

12345

Figure 5 SBUS Connections

5860/R

FACP SBUS

supervised,

power-limited,

Class B

Questo manuale è adatto per i seguenti modelli

Altri manuali Honeywell Pannello di controllo

Honeywell

Honeywell ENVIRAZONE PANEL W8835 Manuale operativo

Honeywell

Honeywell RS-232 Manuale utente

Honeywell

Honeywell Notifier ST.PL4+ Manuale utente

Honeywell

Honeywell Notifier RP-2001 Manuale utente

Honeywell

Honeywell MS-9200UDLSE Manuale utente

Honeywell

Honeywell nfs2-3030 Manuale del proprietario

Honeywell

Honeywell PC8900A Manuale utente

Honeywell

Honeywell NFS-3030 Istruzioni per l'installazione e il funzionamento

Honeywell

Honeywell W8835A Manuale utente

Honeywell

Honeywell Domonial CMI Series Guida utente

Honeywell

Honeywell Fire-Lite Alarms ES-200X Manuale utente

Honeywell

Honeywell TrolATemp TZ-3 TotalZone Manuale operativo

Honeywell

Honeywell Fire-Lite Alarms ACC-25/50 Manuale utente

Honeywell

Honeywell NOTIFIER SFP-10UD Series Manuale utente

Honeywell

Honeywell Galaxy Dimension series Guida utente

Honeywell

Honeywell Silent Knight INTELLIKNIGHT 5600 Manuale utente

Honeywell

Honeywell Galaxy Flex Manuale utente

Honeywell

Honeywell LT-32 Manuale utente

Honeywell

Honeywell PL-1000 Manuale utente

Honeywell

Honeywell IFP-75 Manuale utente

Honeywell

Honeywell Notifier NFS-320/E/C Manuale utente

Honeywell

Honeywell Fire-Lite Alarms MS-9050UD Manuale utente

Honeywell

Honeywell Domonial cmi Manuale utente

Honeywell

Honeywell Notifier AFP-3030 Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche