Honeywell EVOTOUCH CONTROLLER Manuale utente

Installation | Installation | Installatie | Installation | Installazione

evotouch

The Honeywell evotouch comfort control

system is a programmable zoning controller

with the following key features:

Features

• Largetouch-screendisplayforintuitive

operation by ﬁnger.

• Wallortable-topmounting.

Conguration

• Step-by-stepcongurationprocedure

bindsthecontrollertoeachofthe

devicesinthesystem.

• ChoiceofGuidedConguration,

forsimpleapplications,orExpert

Conguration,forcustomisingthe

conﬁguration.

 Note:evohomesystempacksarealready

precongured(seesystempackcontents

sheet).

Programmability

• Upto6periodsperdayineachofthe8

zones.

• Holidaymodereducesthetemperature

for1to99days.

• Economymodereducesthetemperature

settingsinallzones,toreducefuelbills.

Control

• Wirelesscontroltoboiler,radiator

controllers,roomsensors,andunder

ﬂoor heating controllers.

• Independentcontrolofupto8zones,to

optimisecomfortandminimiseenergy

usage.

• OptimumStartfeatureautomatically

calculates when to start heating to

achieve the correct temperature.

• AutomaticSummer/Wintertimechange.

Future expansion

• AUSBport,forfutureupdates.

Installation

Theproductisshippedwithpre-charged

batteries.However,formaximumtimeoffthe

dock,placetheproductoncharge.

Two mounting options are available:

• Awall-mounteddock.

• Atabletopstand.

Whenremovedfromthestand/dockthe

evotouchwillremainpoweredforabout

2hoursbeforeneedingtobereplacedfor

charging.

Productoverview

ENGLISH

Table-topstand

Theevotouchcanbepoweredfromthe

table-topstand.

• Attachtothestandasshown.

Removefrontcovertoexchangecoverplate

or access batteries.

Remove tab to activate batteries.

Batteriesandfrontcover

Rechargeable batteries. Replace with

AA1.2VNiMH2000-2400mAhbatteriesonly.

✓

✗✗

Installation instructions for wall mounting

StandardEU

SchukoWallbox

Minimum

depth

40mm

Insertwiresintopowermodule,observing

correct polarity

Pushpowermoduleintowallboxwithmains

wiring to the rear

Thepowermodulecanbeinstalledina

differentlocationfromtheevotouchunit.

Disconnect low voltage cable from wallplate

terminalblockandextendtheconnectionby

up to 10m max. using 1.0mm² cable. If smaller

sizecableisusedthemaximumdistancewill

reduce(e.g.5m max with 0.5mm² cable).

Observecorrectpolaritywhenconnectingthe

extensioncable.PowerSupplyCablewiresare

Red(+),Black(-).

Attention:Exceedingthemaximumcable

lengthcouldcausesystemmalfunction!

Attachwallplatetowallboxorsurface

(Powermoduleremote).

Optionalspacerforsurface

mounting.

1.2–1.5m

Positionwallboxataheightof1.2m-1.5m.

Caution:Isolatepowersupplyandmakesafebeforewiring

theunittopreventelectricshockandequipmentdamage.

Installationshouldbecarriedoutbyacompetentperson.

Wiresshould

protrude55mm

230V~mains.

230V~

mains.

Usescrewdriver

with 2.5mm

head

Remove

protective ﬁlm

Knock out

requiredholes

Attachevotouchto

wallplate

Notused

+ – X Y

Setting the language, date, and time

The ﬁrst time you apply power to the

evotouchyouwillbepromptedtoselecta

language for the user interface:

• Presstheappropriatelanguage.

Youwillthenbepromptedtosetthedate:

• Press or tosettheday,month,and

year respectively.

• PressDONEtoproceedtosettingthe

time.

• Press or tosetthehourand

minutes respectively.

You can optionally press CLOCK SETTINGS

tochangethetimeformatbetween24HR

and12HR,andchooseautomaticDaylight

Savingtime:

• PressDONEtoproceedwith

conﬁguration.

System conguration

Asequenceofscreensthenguides

you through an automatic conﬁguration

procedure:

• PressYEStoproceed.

YoucanalsoenterGuidedConguration

at any time by pressing the MENU button

for10seconds,andthenselecting

GUIDED CONFIG from the SYSTEM

CONFIGURATION menu.

Settingupevotouch

ENGLISH

Binding

GuidedCongurationbindseachofthe

controldevicesandsensorstoevotouch,to

ensure that the wireless communication is

working correctly.

Afterbindingeachdevice,aprompt

showswhetherbindingwassuccessful;for

example:

Bindingcanfailforthefollowingreasons:

- Thedeviceisnotswitchedon.

- Thedeviceistoofaraway.

- Therearetoomanysolidobjectsinthe

pathtothedevice.

Correcttheproblemandtryagain.

Editing names

During conﬁguration you are given the

optionofeditingthenamesusedtoidentify

the zones in the system. These are the

names seen by the user on the main Home

screen.

Toeditanamethefollowingscreenis

displayed:

• Presstodeletecharacters.

• PressABCtoenterupper-caseletters,

abctoenterlower-caseletters,or123 to

enterdigits.

• Presstheblankkeytoenteraspace.

• PressDONEwhennished.

Conguring mixed applications

TheGuidedCongurationdescribedonthe

following pages assumes all your zones use

thesametypeofcontrol.Ifyouhaveamixed

application,suchas5zoneswithradiator

controland3zoneswithunderoorheating

control,youcansetupthecongurationas

follows:

• UsetheGuidedCongurationto

congurethe5zonesforradiatorcontrol.

• UsetheADD ZONEoptiontoaddthe

3zonesforunderoorheatingcontrol;

see Adding a zone,page9.

• FinallyusetheSYSTEM

CONFIGURATION menu BINDING AND

RF TESToption,doingtheRFtestfor

eachzone.Formoreinformationseethe

Extended Installation Guide.

Conguration–GeneralFeatures

GuidedCongurationistherecommended

optionthersttimeyoucongureevotouch,

asitleadsyouthroughtheessentialstepsin

setting up a system.

• AtthepromptpressYEStoproceed.

Heat demand control

The ﬁrst step is to specify whether the

systemincludesaheatdemandboiler:

• PressNO or YES as appropriate.

IfyoupressedYESproceedasfollows.

IfyoupressedNO skip to the section

Applications below.

Ifthesystemincludesheatdemandcontrol,

thenextstepistocongurethewirelesslink

to the boiler controller:

• PressBIND.

ForinformationaboutbindingseeBinding

on the previous page.

• WhenbindingissuccessfulpressNEXT.

Thefollowingpromptisdisplayed:

• Installthedemanddeviceinitsproper

locationandputthedeviceintothetest

mode.

• PressNEXTwhenready.

Thefollowingpromptisdisplayed:

• PressNEXT.

Applications

The following menu allows you to specify

whichothercomponentsinthesystemneed

tobecongured:

• Selectthetypeofapplicationyouare

conﬁguring.

GuidedConguration

ENGLISH

Inasimplesystem,withevotouchacting

asthethermostattoaheatdemandboiler,

select Thermostat (1 zone),andasingle

zone will automatically be set up for you.

Inalargersystem,withradiatorcontrol

orunderoorheatingprovidingindividual

controlofseparateareas,youwillbe

promptedtosetupeachzone.

Thermostat (1 zone)

IfyouselectedTHERMOSTAT(1zone)the

zonenameisinitiallysettoLIVINGROOM:

• PressLIVING ROOMtoeditthename,

asdescribedinEditing namesearlier,or

NEXT to accept it.

NowproceedasdescribedinSpecifying the

sensors below.

Multizoning radiator heating or

Zone valves

IfyouselectedRADIATORHEATINGor

ZONEVALVESyouneedtospecifythe

number of zones in the system:

• Press or to specify the number of

zones,thenpressNEXT.

Thefollowingscreenletsyoueditthedefault

names chosen for the zones:

• Pressanyzonenametoeditit,as

describedinEditing namesearlier,or

press NEXT to continue.

Ifyouspeciedmorethan6zonespressMORE

toseeoredittheremainingzonenames.

Specifying the sensors

Foreachzonethedisplaypromptsyouto

specify the type of sensor:

• PressINTERNAL or EXTERNAL as

appropriate.

IfyouspeciedEXTERNAL you will then be

promptedtobindthesensor,asdescribed

in Binding earlier in this section.

• PressNEXT to repeat for the sensors in

each zone.

Whenallthezoneshavebeensuccessfully

conguredaconrmationisdisplayed.

•

Press DONE to return to the Home screen.

Note:Onlyonezonecanbecontrolledby

theinternalsensor.Selectingtheinternal

sensor automatically conﬁgures all other

zonestouseexternalsensors.

Addingazone

Thissectionexplainshowtoaddazone

toanexistingconguration,suchasafter

addinganHR80RadiatorControllerto

provideindependentcontrolofaroom.

• PressMENU from the home screen to

displaytheMainMenu.

• PressZONING MENUontheMainMenu

todisplaytheZoningMenu.

• PressZONING CONFIG on the Zoning

Menu.

Thefollowingwarningisdisplayed:

• Pressthebuttonfor5secondstodisplay

theZoningCongurationMenu.

• PressADD ZONE.

Youarerstpromptedtospecifythetypeof

application for the zone:

Formoreinformationaboutapplicationssee

the Extended Installation Guide.

Youarenextpromptedtonamethezone.

Thefollowingmenuthenallowsyoutobind

anactuatorandsensortothezone,andset

uptheschedule:

Forinformationaboutprogramminga

scheduleseetheQuick Start User Guide.

• PressBINDING MODEtobinddevicesto

the new zone.

Youarerstpromptedtobindtheactuatorin

the zone.

• PuttheactuatorinBINDmodeandpress

BIND.

Whenasuccessfulresponsehasbeen

received:

• PressDONE.

Thenextstepistobindasensorinthe

zone. You are given the option of using the

evotouchinternalsensor,oranexternal

room sensor.

Ifthezonecontainstheevotouchcontroller,

andyouwanttousetheinternalsensor,

press INTERNAL.

OtherwisepressEXTERNAL,andyouwill

bepromptedtobindaroomsensorinthe

zone.

• PresstheBIND button on the sensor.

Whenasuccessfulresponsehasbeen

received:

• PressDONE to return to the ADD ZONE

menu.

ENGLISH

Zoning boiler control with

BDR90 Relay module or RF

bridge

Initssimplestsingle-zone

congurationevotouchsensesand

controls the temperature in the main

room,usingitsinternalsensorand

calling for heat from the boiler via the

BoilerRelayorOpenthermBridge

accordingtothedesiredsetpoint.

HR80 radiator control with

central operation

Theevotouchcancontrolupto8zones

usingtheHR80radiatorcontroller.The

evotouch uses the valve position of the

HR80todeterminewhetherornotheat

isrequired.Itwillcontroltheboilervia

theboilerrelayorOpenthermBridge.

In this conﬁguration only the set point

issenttotheHR80s.TheHR80swill

comparethereceivedsetpointto

themeasuredzonetemperatureand

adjustthevalvepositionaccordingly.

Under oor heating control

with central operation and

room units DT92/HCW82

The evotouch can also integrate with

anunderoorheatingcontroller,and

roomunitsDT92/HCW82,toprovide

individualcontrolofupto8rooms.

TheDT92/HCW82roomsensorsand

setpointadjusterscommunicate

directlywithevotouch.

Three simple system applications

Relay module

Boiler Relay or Opentherm Bridge

Boiler

0 .. 100%

ON/OFF

19.

HR80

Relay module

Boiler Relay or Opentherm Bridge

Up to 8 zones

Boiler

0 .. 100%

ON/OFF

19.

Relay module

Boiler Relay or Opentherm Bridge

Antenna

HRA80

Up to 8 zones

Boiler

HCW82

DT92

0 .. 100%

ON/OFF

Underfloor heating

controller

HCE80(R)/HCC80(R)

19.5

Altri manuali per EVOTOUCH CONTROLLER

Indice

Lingue:

Altri manuali Honeywell Sistema di controllo

Honeywell

Honeywell SILENT KNIGHT SK-Zone-6 Manuale utente

Honeywell

Honeywell RP-2002 Manuale utente

Honeywell

Honeywell XLS80e Manuale utente

Honeywell

Honeywell Experion PKS Manuale utente

Honeywell

Honeywell W180 Manuale utente

Honeywell

Honeywell W7620 Manuale utente

Honeywell

Honeywell Experion LX 8 series Manuale utente

Honeywell

Honeywell SmartValve SV9540 Manuale utente

Honeywell

Honeywell ACC 50 Manuale utente

Honeywell

Honeywell Excel 800 Manuale di installazione e funzionamento

Honeywell

Honeywell 5701 Manuale utente

Honeywell

Honeywell W7080A Manuale utente

Honeywell

Honeywell UMC800 Manuale utente

Honeywell

Honeywell VR8304 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

Honeywell

Honeywell BCS 3600 Manuale utente

Honeywell

Honeywell AUTOMATIC CONTROL SI Edition Manuale di installazione e funzionamento

Honeywell

Honeywell Excel 5000 System Series Manuale utente

Honeywell

Honeywell C7400 Manuale utente

Honeywell

Honeywell Experion LX Manuale utente

Honeywell

Honeywell ComfortPoint Open Manuale di installazione e funzionamento

Honeywell

Honeywell MCBA14C Manuale di servizio

Honeywell

Honeywell touchpoint Pro Manuale utente

Honeywell

Honeywell SPZ-8000 Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente

EMKO

EMKO TRANS-SYNCRO Manuale utente

Dover

Dover TWG GC ELEMENT II Manuale di programmazione