Honeywell EIM Guida all'installazione

Altri manuali Honeywell Unità di controllo

Honeywell

Honeywell NOTIFIER M701E Manuale utente

Honeywell

Honeywell RMG 213 Guida

Honeywell

Honeywell NOTIFIER FW-MM Manuale utente

Honeywell

Honeywell Kromschroder TC 1 Manuale utente

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manuale utente

Honeywell

Honeywell Kromschroder GIK Series Manuale utente

Honeywell

Honeywell TC Series Manuale

Honeywell

Honeywell D22 Manuale utente

Honeywell

Honeywell Fire-Lite ECC-RPU Manuale tecnico

Honeywell

Honeywell Notifier XP6-R Manuale utente

Honeywell

Honeywell JADE W7220 Manuale operativo

Honeywell

Honeywell ADEMCO 4204 Manuale utente

Honeywell

Honeywell CentraLine CLIOL822A Manuale operativo

Honeywell

Honeywell R7140G Manuale utente

Honeywell

Honeywell FF-SRS5988 Manuale utente

Honeywell

Honeywell 4219 Istruzioni per il montaggio

Honeywell

Honeywell Velociti Series Manuale utente

Honeywell

Honeywell Ex-Or MLSUC500 Manuale utente

Honeywell

Honeywell S7800A1001 Manuale utente

Honeywell

Honeywell FIRE-LITE ALARMS TS540/1 Manuale utente

Honeywell

Honeywell Hometronic HAV 20 Guida

Honeywell

Honeywell satronic DMG 971 Istruzioni per l’uso

Honeywell

Honeywell V5004TF Manuale utente

Honeywell

Honeywell VR8204 Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

Equipment Interface Module

Training

EIM Module Basics

•Reasons to use EIM Modules:

1.)Not enough wires to thermostat or want to use

wireless thermostat.

2.)Want to monitor system through honeywell

3.)Installing a humidifier, ventilator, dehumidifier

4.)Use of dry contacts for alarms, alerts, unit

protection.

EIM Module Mounting Locations

•1.)Mounting EIM Module on horizontal

applications can be accomplished by mounting to

supply or return air plenums.

•2.)Mounting EIM Module on vertical applications

can be accomplished by mounting to supply

ductwork or walls in closet.

•3.)Mounting EIM Module on package units can be

accomplished by installing anywhere inside unit

where water can not enter. Examples: mount on

splitter inside, interior wall, heat strip

compartment.

EIM Module Wiring

•1.) If wiring 24 volts to thermostat Red and

Common to be connected at R and C at the

(TO THERMOSTAT) terminals on EIM Module.

•2.)Wiring to equipment is standard

connections: example Y to Y, G to G on EIM

Module terminals.

•3.) Wiring of discharge sensor to go to S2

terminals on EIM Module, note does not

matter which wire goes to which.

EIM Module Wiring Cont

•4.) Wiring of return air sensor to be connected to

S1 terminals on EIM Module, note does not

matter what wire goes to which terminal.

•5.)Wiring of condensate safety switch must be

connected to the S3 terminals, again does not

matter which wires.

•6.)Wiring of drain pan sensor (optional) must be

connected to S4 terminals for normally closed

circuit, and 24 volts to Red and Common

Programming Redlink for EIM Module

•1.)Follow instructions that come up on screen when

new thermostat is first installed or reset to factory

default settings then follow instructions.

•2.)Go through thermostat until thermostat reads:T-Stat

Controls an Equip Module:NO switch using arrow keys

to yes. Next hit yes then next says to press connect at

EIM Module. Press connect and wait to see green LED

start flashing then go to thermostat and hit next.

Should say connecting, once connected thermostat will

say connected, hit next and you have now linked

thermostat to Module.

Programming Continued

•3.)Next screen on thermostat says connect

redlink devices, this is where you connect all

wireless devices.

•4.)Continue through set up until thermostat

says:Wired Sensor on S terminals:no. Switch

to yes using arrow keys and hit next.

•5.)Next screen asks if wired remote indoor

sensor:no leave at no these are not remote

indoor sensors.