Honeywell SILENT KNIGHT IDP-Control Manuale utente

LABEL

J1 UNDER LABEL

BACK OF

MODULE

K200-09-00 1 I56-2725-003

IDP-Control Supervised

Control Module

INSTALLATION AND

MAINTENANCE INSTRUCTIONS

Before Installing

This information is included as a quick reference installa-

tion guide. Refer to the control panel installation manual

for detailed system information. If the modules will be

installed in an existing operational system, inform the

operator and local authority that the system will be tem-

porarily out of service. Disconnect power to the control

panel before installing the modules.

NOTICE: This manual should be left with the owner/

user of this equipment.

General Description

IDP-Control Supervised Control Modules are intended

for use in intelligent, two-wire systems, where the in-

dividual address of each module is selected using the

built-in rotary switches. This module is used to switch an

external power supply to notification appliances. It also

supervises the wiring to the connected loads and reports

their status to the panel as NORMAL, OPEN, or SHORT

CIRCUIT. The IDP-Control has two pairs of output ter-

mination points available for fault-tolerant wiring and a

panel-controlled LED indicator.

Figure 1A. Controls

and indicators:

Figure 2A. Module mounting with barrier:

C0219-01

C0217-01

Specifications

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 6.5 mA (LED on)

Average Operating Current: 390µA (LED flashing)

Regulated External

Supply Voltage: (between Terminals T3 and T4)

Maximum: 80 Volts (RMS or DC)

Drain on External Supply: 2 mA Maximum (using

internal EOL relay)

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% non-condensing

Dimensions: 41/2˝ H x 4” W x 11/4˝ D

(Mounts to a 4˝ square by

21/8˝ deep box.)

Accessories: SMB500 Electrical Box

Compatibility Requirements

To ensure proper operation, this module shall be con-

nected to a compatible Silent Knight system control pan-

els only (list available from Silent Knight).

Mounting

The IDP-Control mounts directly to 4 square electri-

cal boxes (see Figure 2A). The box must have a mini-

mum depth of 21/8˝. Surface mounted electrical boxes

(SMB500) are available.

Wiring

NOTE: All wiring must conform to applicable local

codes, ordinances, and regulations. When using control

modules in nonpower limited applications, UL require-

ments for the separation of power-limited and nonpower-

limited terminals and wiring must be met. The barrier

must be inserted into a 4˝ × 4˝ × 21/8˝ junction box, and

the control module must be placed into the barrier and

attached to the junction box (Figure 2A). The power-lim-

ited wiring must be placed into the isolated quadrant of

the module barrier (Figure 2B).

56789

TENS

ONES

ADDRESS

LOOP

ISOLATED

QUADRANT

TENS

ONES ADDRESS

LOOP

TENS

ONESADDRESS

LOOP

Figure 1B. Jumper location:

C0458-00

Figure 2B:

C0218-01

MODULE

FROM PANEL OR

(+)

(-)

TO NEXT

(+)

(-)

DEVICE

(+)

(-)

CONTROL

(-)

(+)

47K EOL

RESISTOR

ELR-47K

UL LISTED EOL RELAY

SHOWN ENERGIZED

24 VDC COIL

EOLR-1 TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.

ONE RELAY REQUIRED FOR EACH CIRCUIT.

MODULE POLARITIES ARE

SHOWN IN ALARM

CONNECT MODULES TO LISTED COMPATIBLE

32 VDC MAX.

IS RECOMMENDED

24 VDC CIRCUIT

3 & 4. BREAK WIRE RUN TO PROVIDE

SUPERVISION OF CONNECTIONS.

DO NOT LOOP WIRE ON TERMINALS

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

(-)

(+)

TWISTED PAIR

SILENT KNIGHT CONTROL PANELS ONLY

PREVIOUS DEVICE

(-)

(+)

24 VDC POWER SUPPLY

ISOLATED, REGULATED, POWER

LIMITED PER NFPA 70.

LISTED FOR FIRE PROTECTION WITH

BATTERY BACKUP.

5 4

5 6 7 8 9

TENS

ONES

ADDRESS

LOOP

7 8

SIGNAL LINE CIRCUIT (SLC)

MODULE

FROM PANEL OR

(+)

(–)

TO NEXT

(+)

(–)

DEVICE

(+)

(–)

CONTROL

(–)

(+)

(–)

(+)

UL LISTED EOL RELAY

SHOWN ENERGIZED

24VDC COIL

EOLR-1

MODULE POLARITIES ARE

SHOWN IN ALARM

CONNECT MODULES TO LISTED COMPATIBLE

24 VDC CIRCUIT

3 & 4. BREAK WIRE RUN TO PROVIDE

SUPERVISION OF CONNECTIONS.

DO NOT LOOP WIRE ON TERMINALS

ALL WIRING SHOWN IS SUPERVISED

AND POWER LIMITED

(+)

SILENT KNIGHT CONTROL PANELS ONLY

PREVIOUS DEVICE

EOL RESISTOR IS

INTERNAL AT

TERMINALS 8 & 9

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

(–)

24 VDC POWER SUPPLY

ISOLATED, REGULATED, POWER

LIMITED PER NFPA 70.

LISTED FOR FIRE PROTECTION WITH

BATTERY BACKUP.

TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.

ONE RELAY REQUIRED FOR EACH CIRCUIT.

5 4

5 6 7 8 9

TENS

ONES

ADDRESS

LOOP

7 8

SIGNAL LINE CIRCUIT (SLC)

K200-09-00 2 I56-2725-003

Figure 3. Typical notification appliance circuit configuration, NFPA Style Y:

Figure 4. Typical fault tolerant notification appliance circuit configuration, NFPA Style Z:

C0808-03

C0807-03

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)

state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communi-

cate with the panel before connecting circuits controlled by the module.

1. Install module wiring in accordance with the job draw-

ings and appropriate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer),

as shown in Figure 2A.

IMPORTANT: When using the IDP-Control for fire

fighter telephone applications, remove Jumper (J1) and

discard. The Jumper is located on the back under the

product label as shown in Figure 1B. 7550 Meridian Circle

Maple Grove, MN 55369-4927

763-493-6455; 800-328-0103

Fax: 763-493-6475

http://www.silentknight.com

Altri manuali Honeywell Unità di controllo

Honeywell

Honeywell SILEN KNIGHT IDP-Relay-6 Manuale utente

Honeywell

Honeywell Silent knight 5895XL Manuale utente

Honeywell

Honeywell SG150 Manuale utente

Honeywell

Honeywell Silent knight 5895XL Istruzioni operative

Honeywell

Honeywell LYNXDM-GSM Istruzioni per il montaggio

Honeywell

Honeywell VE4000 Series Manuale utente

Honeywell

Honeywell 9410 Series Manuale di istruzioni

Honeywell

Honeywell V5011N Manuale utente

Honeywell

Honeywell 4219 Istruzioni per il montaggio

Honeywell

Honeywell M5410C1001 Manuale utente

Honeywell

Honeywell EXCEL 5000 OPEN T7460A Manuale utente

Honeywell

Honeywell RV280 Manuale utente

Honeywell

Honeywell 4286 Guida all'installazione

Honeywell

Honeywell D05FS Manuale utente

Honeywell

Honeywell 010690.02 Manuale di istruzioni

Honeywell

Honeywell Notifier XP6-R Manuale utente

Honeywell

Honeywell V48F Manuale operativo

Honeywell

Honeywell SmartPAC 2 Manuale utente

Honeywell

Honeywell FV300 Manuale utente

Honeywell

Honeywell L6190A Manuale utente

Honeywell

Honeywell Maxon SMA11 Manuale utente

Honeywell

Honeywell N-1000 Manuale di servizio

Honeywell

Honeywell 5496 Istruzioni operative

Honeywell

Honeywell Fire-lite FFT Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente