Honeywell AUTOCUBE 8200 Manuale utente
AutoCube 8200
Quick Start Guide
AUTOC-EN-QS-01 Rev D
6/17
1
Out of the Box
Make sure your shipping box contains these items (full kit):
• AutoCube camera with protective foam
• Stand with cable(s) and clamps
•4cablecovers
• Stand clamp
• Display and display holder (optional accessories)
• Mounting hardware
• Stand base cover
Unpacking the Box Contents
Carefully unpack the box contents.
Caution: Do not remove the protective foam from
the camera during installation.
Caution: Do not open the AutoCube camera! The
warranty and certification is void if this
stipulation is ignored. The device may only
be opened by authorized persons.
2
What You Need
• Drill with a Ø12.5 mm drill bit
•Measuringtape
• Allen wrench, 3 mm and 5 mm
• Adjustable wrench
• Hole saw Ø32 mm (optional)
•Pliers(optional)
• Phillips screw driver (optional)
3
Installation Overview
A
D
H
4
Dimensions
The following are the recommended dimensions for installation.
The camera angle (A) and distance from the pole to the center of
the measurement area (D) vary depending on pole height (H).
Note: If you are not using the pole, the camera height (H),
measured from the front center of the camera, should be
≈1.5 m / ≈5 ft or ≈1.8 m / ≈ 6 ft.
Before You Begin
Determine where you will place the stand and if the cables will
exit through the bottom of the stand (going through the mount-
ing surface) or the side of the stand.
Prepare the Mounting Surface
Use the stand clamp as a template to trace and drill 4 holes (12
mm diameter) in the mounting surface.
Note: If the cables will exit through the bottom of the pole and
through the mounting surface, you must also drill the
center hole of the stand clamp large enough to pull the
cable(s) through.
Pole Height (H) Camera Angle (A) Distance (D)
≈160 cm / ≈5.25 ft ≈30° ≈63 cm / ≈2 ft
≈190 cm / ≈6.25 ft ≈45° ≈133 cm / ≈4.3 ft
5
Hardware Overview
Camera with
protective foam
USB cable
to camera
Pole
Screws used to adjust
stand height (x4)
Display holder
(optional - can be
mounted on any
side of the pole)
Stand cover
Mounting screws (x4)
Stand clamp
USB cable(s)
to PC
Leveling screws (x4)
Stand base
Camera clamp
6
Adjust Pole Height
Pole height (H) is measured from the top of the pole to the top of
the measurement area or scale.
1. Loosen the screws on each side of the pole
(4x) using an Allen wrench.
2. Slide the pole up to the desired height.
3. Tighten screws on each side of the pole to
secure the pole.
4. Pull the camera cable out of the bottom of
the pole until approximately 25 cm (10 in)
remain exposed at the top of the pole so it
can be attached to the camera later.
5. Cut the cable covers to the length needed to
cover the cable channels on the pole. Snap
into cable channels.
Note: Cut the cable cover for the back side of the
pole sightly shorter than the others so that
the camera cable can exit and be
connected to the camera.
Cable
covers
7
Route the Cables
By default the cables are routed out of the bottom of the stand.
To route the cables out of the side:
1. Pull up the stand cover - some resistance is normal.
2. Pull the cables up and through the side exit on the pole.
Cable exit
8
Install the AutoCube Camera
1. Angle the clamp on the top of the pole perpendicular to the
pole. Turn the knob to loosen the clamp.
2. Insert the ball of the camera into the clamp. Make sure the
camera is right side up (Honeywell logo on front right side
up). Adjust the camera to the correct angle (A) from the pole
(see Dimensions at the beginning of this document).
3. Turn the knob to tighten the clamp. Be sure it is tight
enough so that the camera will not move.
4. Attach the USB cable at the top of the pole to the camera.
Secure the cable to the camera by tightening the screws by
hand.
Note: Be sure the camera is horizontal to the measurement area
and aimed directly at the area.
Caution: DO NOT remove the protective foam during
installation.
Knob to tighten or
loosen clamp
9
Note: Keep the protective foam on the camera until installation is
finished.
Mount the Stand
Recommended 2 person operation.
1. Rotate the stand assembly upright on the mounting sur-
face. Align stand base to previously drilled holes.
Note: If cables exit through the bottom of the pole, pull them
through the mounting surface.
2. Place washers on the stand base then the mounting bolts
through the stand base and mounting surface. Thread into
the stand clamp placed under the mounting surface.
Altri manuali per AUTOCUBE 8200
2
Indice
Altri manuali Honeywell Telecamera di sicurezza
Honeywell
Honeywell HBW2PR2 Manuale utente
Honeywell
Honeywell HCC334L Manuale utente
Honeywell
Honeywell 2450Cm Series Manuale utente
Honeywell
Honeywell HD4D Series Manuale utente
Honeywell
Honeywell HDT Manuale utente
Honeywell
Honeywell 2450Cm Series Manuale utente
Honeywell
Honeywell HD4D3X Manuale utente
Honeywell
Honeywell H3D2S2 Manuale utente
Honeywell
Honeywell HD70 Series Manuale utente
Honeywell
Honeywell HDZ302D Manuale utente
Honeywell
Honeywell 2450Cm Series Manuale utente
Honeywell
Honeywell 720P Manuale utente
Honeywell
Honeywell HCCWD484X Manuale utente
Honeywell
Honeywell HEC12 Manuale utente
Honeywell
Honeywell EQUIP HD4DIP Manuale utente
Honeywell
Honeywell HCX13M Manuale
Honeywell
Honeywell HD51 Series Manuale utente
Honeywell
Honeywell 2450Cm Series Manuale utente
Honeywell
Honeywell equIP H2S1P6X Manuale utente
Honeywell
Honeywell HCU484X Manuale utente
