Honeywell HBT083P Manuale utente

CSHBT083PV1 12/04 Rev.A

HBT083P/MDT083P

HBT083P/MDT083PHBT083P/MDT083P

HBT083P/MDT083P

KSU/PBX Telephone

KSU/PBX TelephoneKSU/PBX Telephone

KSU/PBX Telephone

Distribution Hub/Module

Distribution Hub/ModuleDistribution Hub/Module

Distribution Hub/Module

INSTALLATION GUIDE

Description

The HBT083P and MDT083P Hub and Module provide distribution of four (4) incoming telephone lines to eight

(8) locations via 110 connectors, and One (1) video signal to eight (8) locations. The Hub/Module also includes

a 12dB amplifier and two (2) coax pass through connections for Satellite TV. This Module will requires 6-inches

of space in a QuickNetwork rough-in can.

Features

• Twelve ports

• Four line capability

• RJ31x port

• Labeling space for every port

Important Warnings

♦ Never install or work with telephone wiring during a lightning storm.

♦ Never install telephone jacks in wet locations unless the jack is specifically designed for use in wet locations.

♦ Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at

the network interface.

♦ Use caution when installing or modifying telephone lines.

♦ Have the Electrician connect the AC outlet to branch circuit power. The connection should be in accordance

with the National Electrical Code, Articles 110, 250 and 300.

Installing the Distribution Hub/Module

Connect the service input cable to the center F-type

coax port on the module labeled “CATV/ANT IN”. These

signals can be either Cable TV, Antenna or a modulated

video signal. Connect a coax cable between the “12 V

DC IN” port and the provided DC power module. Once

the input and power cables have been connected the

video signal will be distributed the video signal to all of

the outputs on the module. There are also two Pass

through Aux. ports that can be use to pass satellite

signals.

Connecting TV outlets to outputs

1. Remove the silver terminating caps ONLY from the

ports that will be connected to outlet cables.

Keeping the caps on unused port, will help prevent

unwanted video signals from entering your TV

system.

2. Connect the outlet cables to the module.

3. Connect the incoming cables from the Satellite TV to

the pass-through F connectors on the rear of the

module.

4. Connect the outgoing satellite cables between the

receiver and the front side of the module.

Connecting Telephone Service

Connecting Incoming Phone Lines

1. Trim back the PVC jacket on the incoming phone

cable approximately ¾-inch (be sure to re-label if

necessary) allowing for a bend radius of at least

four times the diameter of the CAT5 telephone

cable.

2. Separate the pairs from each other but do not

untwist the pairs. Be sure to label each

connection on the provided documentation

template painted on the face of the module.

Note: Do not untwist the conductors more than ½-inch from

the point of termination.

3. Following the 568A color code that is printed on

the 110 connectors, punch down the incoming

cables on the module’s 110 connectors. Start with

the blue pair punch the cable down into the slots.

4. Punch down all the Cat5e cables in the same

fashion, positioning and trimming each in order to

maintain neatness.

Note: Make sure that the Tip and Ring are properly

connected to the 110 punch down. In most cases the

blue/white is first and then the white/blue.

5. Once the remaining cables have been connected

(up to four lines) the incoming phone lines will be

distributed to the outlet ports on the top side of

the module.

Connecting outgoing telephone cables

The outgoing RJ45 ports will accept cables with either

RJ45 or RJ11 connectors. RJ45 termination is

recommended so that the four line capability can be

used. When terminating the cables follow the 568A

standard.

If a MDP3 patch module is being installed, connect a

patch cord between the telephone outputs and the

zones on the MDP3 patch module.

Connecting the module to a Security System

After phone service has been connected to the

module, route a CAT5 patch cord between the RJ31x

port and the security system. Cut the RJ45 connector

off at the Security system end and use the following

diagram to connect the phone service to the security

system and to the module.

‡CSHBT083PV1aŠ

CSHBT083PV1 12/04 Rev. A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Honeywell Interruttore

Honeywell

Honeywell B Manuale operativo

Honeywell

Honeywell ZW4103 Manuale utente

Honeywell

Honeywell MICRO SWITCH GSX Manuale utente

Honeywell

Honeywell 39348 Manuale utente

Honeywell

Honeywell RPLS731B Manuale utente

Honeywell

Honeywell Dolphin 7800 Manuale operativo

Honeywell

Honeywell ZW4008 Manuale utente

Honeywell

Honeywell ZW4203 Manuale utente

Honeywell

Honeywell Fema DCM-203-574 Series Manuale utente

Honeywell

Honeywell AML54 Series Manuale utente

Honeywell

Honeywell krom schroder 03250831 Manuale utente

Honeywell

Honeywell WBX Series Manuale utente

Honeywell

Honeywell ZW4005 Manuale utente

Honeywell

Honeywell F300 Manuale di istruzioni

Honeywell

Honeywell 272630D Manuale utente

Honeywell

Honeywell RPLS730B Manuale utente

Honeywell

Honeywell 5869 Manuale utente

Honeywell

Honeywell PLS750C Manuale utente

Honeywell

Honeywell Limitless WGLA Series Manuale utente

Honeywell

Honeywell ZW4009 Manuale utente

Honeywell

Honeywell 88173 Manuale utente

Honeywell

Honeywell C6097 Manuale

Honeywell

Honeywell Krom Schroder DG B Series Manuale utente

Honeywell

Honeywell CX Series Guida rapida

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente