HP JG560A Manuale utente

Installation tools

Introduction to the opacity shield kit

The installation tools are not provided with the switch. Prepare them yourself.

Phillips

screwdriver

ESD-preventive wrist

strap

Spanner

Applicable products

Alcohol-based

cleaning pad

Two-holed mounting bracket

(2 in total)

Hex bolt

(3 in total)

M3 countersunk-head screw (used to

secure the opacity shield, 3 in total)

Tamper evidence

label (30 in total)

Opacity shield

(1 in total)

HP 5800-24G-PoE+ Switch (JC099A/JC099B)

HP 5800-24G-PoE+ TAA Switch (JG254A/JG254B)

HP 5800-48G-PoE+ Switch with 1 Interface Slot (JC104A/JC104B)

HP 5800-48G-PoE+ TAA Switch with 1 Interface Slot (JG257A/JG257B)

M4 countersunk-head screw (used to

secure the mounting brackets, 4 in total)

Installation preparation

HP 5800 switches meet the requirement of FIPS security level 2.

The installation procedures must be performed by qualified personnel.

Installing the opacity shield

Before installation, read the Compliance and Safety Manual for the compatible switch

of the opacity shield kit.

Make sure the operating temperature is not higher than 40°C (104°F).

Wear an ESD-preventive wrist strap, and make sure the wrist strap makes good skin

contact and is well grounded.

The two-holed mounting brackets are not designed to support the weight of the switch.

To mount the switch to the rack, install a rack shelf in a proper position of the rack,

place the switch on the rack shelf, and use screws to secure the two-holed mounting

brackets to the rack posts.

Applying tamper evidence labels

The mounting bracket is installed

at the port side of the chassis.

The mounting bracket is installed at

the power supply side of the chassis.

Make sure the chassis temperature is above 10°C (50°F).

Before applying tamper evidence labels, use alcohol-based cleaning pads to clean the

chassis and air dry the cohesive areas.

Apply tamper evidence labels to all field replacement units

(for example, opacity shields and interface cards), USB ports, and any M3

countersunk-head screw on an opacity shield.

The methods for applying tamper evidence labels are the same when the mounting

brackets are installed at the port side and the power supply side. In the following

example, the mounting brackets are installed at the port side.

M3 countersunk-

head screw

M4 countersunk-

head screw

Hex bolt M4 countersunk-head screw

Hex bolt

countersunk-

head screw

The methods for installing the opacity shields to an HP 5800-24G-PoE+ Switch and an

HP 5800-48G-PoE+ Switch with 1 Interface Slot are the same. This section uses an HP

5800-24G-PoE+ Switch as an example.

Only use the screws and hex bolts that are supplied in the opacity shield kit to secure

the opacity shield.

© Copyright 2015 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice.

Applying tamper evidence labels (chassis front view)

Applying tamper evidence labels (chassis rear view)

5998-3560a

Altri manuali HP Hardware per computer

HP

HP Sangoma 2 Istruzioni per l'installazione

HP

HP P Class 450/500/550/600/650/700/750 Manuale

HP

HP Xw4600 - Workstation - 2 GB RAM Manuale utente

HP

HP MCS G2 Guida all'installazione

HP

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manuale utente

HP

HP 381513-B21 - Smart Array P800 Controller... Manuale utente

HP

HP Vectra VE4 Manuale utente

HP

HP Apollo r2800 Istruzioni per l'installazione

HP

HP E2465A PowerPC 604 PGA Manuale utente

HP

HP MCS-200 Manuale utente

HP

HP AF079A Guida all'installazione

HP

HP HPE LSWM2XGT2PM Manuale utente

HP

HP Integrity rx8620 Manuale utente

HP

HP GbE2c - Blc Layer 2/3 Fiber SFP Option Come usare

HP

HP FlexFabric 12908E LSXM108XFAN Manuale utente

HP

HP Z400 - Workstation Manuale utente

HP

HP 8168E Manuale utente

HP

HP StoreOnce 2700 Manuale dell'operatore

HP

HP 98625A Manuale utente

HP

HP P Class 450/500/550/600/650/700/750 Manuale

HP

HP Smart Array P400 Istruzioni utente

HP

HP Rp5700 - Point of Sale System Istruzioni per l'installazione

HP

HP Xw4600 - Workstation - 2 GB RAM Manuale utente

HP

HP Model 744 - VME Workstation Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente