HP D7171A - NetServer - LPr Manuale di installazione e funzionamento
HP NetServer LXr Pro8
200 MHz/1 MB Processor
Board
Upgrade Guide
HP Part Number 5967-2101
Printed in January 1998
ii
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall
not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent of
Hewlett-Packard Company.
Hewlett-Packard Company
Network Server Division
Technical Marketing Department / MS 53U-FJ
5301 Stevens Creek Boulevard
P.O. Box 58059
Santa Clara, CA 95052-8059 USA
© Copyright 1998, Hewlett-Packard Company.
Audience Assumptions
This guide is for the person who installs, administers, and troubleshoots LAN
servers. Hewlett-Packard Company assumes you are qualified in the servicing of
computer equipment and trained in recognizing hazards in products with
hazardous energy levels.
iii
Contents
1 Overview.......................................................................................................1
About This Guide...........................................................................................1
Additional Information................................................................................1
Verify Contents..............................................................................................1
Tools Required...............................................................................................3
2 Plan the Upgrade..........................................................................................5
Determine Where to Place the Processor Board............................................5
3 Perform the Upgrade....................................................................................7
Power Down the HP NetServer......................................................................7
Slide Out the Satellite Chassis.......................................................................9
Lift and Remove Top Cover of Satellite Chassis..........................................11
Remove the Terminator Board.....................................................................12
Install the Processor Board ..........................................................................15
Slide the Satellite Chassis Back Into Place ..................................................15
A Warranty and Support...............................................................................19
Hardware Warranty......................................................................................19
HP Repair and Telephone Support...............................................................19
B Regulatory Information.............................................................................21
Notice for USA: FCC Radio Frequency Emissions Statements.....................21
Class A Product Statement......................................................................21
Notice for EU...............................................................................................22
Index...............................................................................................................23
1
1Overview
About This Guide
This guide describes the installation of the 200 MHz/1 MB Processor Board
Accessory Kit in HP NetServer LXr Pro8 systems. The processor board includes
two 200 MHz/1 MB CPU chips, on which two heat pipes are mounted for
efficient cooling.
Use this guide to install up to three additional processor boards in a system that
already has one 200 MHz/1MB processor board installed.
In addition to the installation instructions, this guide contains regulatory
information.
Additional Information
For other information about your HP NetServer LXr Pro8, refer to the HP
NetServer LXr Pro8 User Guide.
Verify Contents
CAUTION Do not remove the processor board from its bag until you are
ready to install it. Make sure the bag remains sealed. The
CPU chips are sensitive to humidity, so desiccant has been
packed in the bag containing the processor board. When the
processor board has been installed and the HP NetServer is
running, the chips are no longer sensitive to humidity.
Unpack the shipping box and verify that you received the contents listed on the
next page for the 200 MHz/1 MB Processor Board Accessory Kit. If anything is
missing or damaged, or if the bag around the processor board is not sealed, call
your reseller.
Chapter 1 Overview
2
1. Processor board, shown in Figure 1-1, has the following parts mounted on
it:
• Two 200 MHz/1 MB CPU chips
• Two heat pipes
• Two VRMs (voltage regulator modules)
Be sure to keep the bag around the processor board sealed until you are
ready to install the board.
2. HP NetServer LXr Pro8 200 MHz/1 MB Processor Board Upgrade Guide
(this guide).
3. Update Return Kit that explains how to return unused terminator boards
to HP for environmentally safe disposal.
4. HP Navigator CD-ROM. You are not required to use the HP Navigator
CD-ROM to reconfigure your system after installing the new processor
board. However, we recommend that you use it to ensure that you have the
latest drivers and information.
Figure 1-1. 200 MHz/1MB Processor Board
Chapter 1 Overview
3
Tools Required
• An antistatic service kit (3MTM 8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.
• Number 2 Phillips head screwdriver.
5
2 Plan the Upgrade
Up to four processor boards, each with two 200 MHz/1 MB CPU chips, can be
installed in the HP NetServer LXr Pro8 system. All four processor board slots on
the system board must be filled, even when fewer than four processor boards
(eight CPUs) are installed. Each processor board slot must contain one of two
kinds of boards:
• Processor board. The processor board contains two 200 MHz/1MB CPU
chips with two heat pipes and two VRMs (voltage regulator modules).
or
• Terminator board. The terminator board uses the same board blank as
the processor board, but it does not contain the CPU chips, heat pipes, or
VRMs. Each terminator board contains just the components necessary to
terminate the bus.
During start up, the control panel of the HP NetServer LXr Pro8 displays how
many CPUs the system detects.
Determine Where to Place the Processor Board
The system comes standard with one processor board and three terminator
boards. Before you can add a processor board, you must remove a terminator
board.
The HP NetServer LXr Pro8 has two CPU buses: A and B. Bus A, containing
slots A1 and A2, is the primary bus. Bus B, containing slots B1 and B2, is the
secondary bus. Table 2-1 shows how processor boards can be added to the HP
NetServer LXr Pro8 to keep the two buses balanced.
Chapter 2 Plan the Upgrade
6
Table 2-1. Processor Board Configurations
Total Number of CPU
Chips in System Board in
Slot A1 Board in
Slot A2 Board in
Slot B1 Board in
Slot B2
2 CPUs Processor
board Terminator
board Terminator
board Terminator
board
4 CPUs Processor
board Terminator
board Processor
board Terminator
board
6 CPUs Processor
board Processor
board Processor
board Terminator
board
8 CPUs Processor
board Processor
board Processor
board Processor
board
Figure 2-1 shows a diagram of a system board which labels the processor board
slots. You might want to use this diagram to mark or highlight the slot (or slots)
on the system board where you will remove a terminator board to install a
200 MHz/1 MB processor board.
Figure 2-1. System Board of HP NetServer LXr Pro8
Altri manuali per D7171A - NetServer - LPr
117
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali HP Hardware per computer
HP
HP ML570 - ProLiant - G2 Manuale utente
HP
HP t730 Thin Client Manuale utente
HP
HP Z400 - Workstation Manuale utente
HP
HP MPEGscope Portable Guida utente
HP
HP ProLiant DL140 Manuale utente
HP
HP D7171A - NetServer - LPr Manuale utente
HP
HP 64782 Manuale utente
HP
HP C-CLASS BLADESYSTEM 409513-B21 Istruzioni utente
HP
HP Smart Array P400 Istruzioni utente
HP
HP Adaptec ultra p2280a Manuale utente
HP
HP USB 3.0 4-Port SuperSpeed PCIe x1 Card Manuale utente
HP
HP 3000 Series Manuale
HP
HP A4800A Guida
HP
HP SC08Ge Manuale utente
HP
HP Pavilion xl700 - Desktop PC Manuale utente
HP
HP Smart Array 5300A Manuale utente
HP
HP FlexFabric 12908E LSXM108XFAN Manuale utente
HP
HP HP-UX 10.20 Manuale utente
HP
HP Z Turbo Drive Quad Pro Manuale utente
HP
HP 5930-4Slot Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
